ITCFDOSAB IN-DASH INSTALLATION KIT FOR 2015-UP FORD MUSTANG SINGLE ZONE MANUAL/ DUAL ZONE AUTOMATIC CLIMATE CONTROLS ADASHMODIFICATION REOUIREDA- Kit Content 1. 2. 3. 4. 5. 6. 7. 8. Face Panel w/ UAC (7773) Right Bracket (7774) Left Bracket (7775) Three Button Switch Trim (777 6) Four Button Switch Trim (7777) Back Cover (7778) PBC Spacer (7779) Pocket(6761) Tools Required Panel Removal Tool Screwdriver Pc,tary Cutting Tool Filing Tool 'j' : ~ =- .
INSTALLATION GUIDE RAD/0D/SASSEMBLY STEP 1 RADIO DISASSEMBLY Image A: Remove the two (passenger and driver side) knee panels on the lower console. Image B: After removing the knee panels, Remove two exposed screws STEP 2 RADIO DISASSEMBLY Image A: Using a panel removal tool, carefully remove the tray located below the USB and 12V socket ports, then remove and retaintwo screws exposed. Image B: Lift and slightly pullback the center console, but do not remove.
INSTALLATION GUIDE STIP ' RAD/00/SASSEMBLY RADIO DISASSEMBLY Remove the four screws securing the OEM panel to the dash; then unplug and remove the panel (see image on the right). ITIP 6 RADIO DISASSEMBLY Remove the OEM display and the CD receiver by unscrewing the four screws for each component (8 screws total, circled). Next, unplug all wiring and remove (see image on the left).
INSTALLATION GUIDE STEP 8 Panel Preparation Panel Preparation Remove fifteen (15) screws and the 12V socket located behind the OEM climate control'panel and retain for later installation; then remove the PCB board back cover. NOTE: The amount of screws may vary with vehicle model. Retain the 12V socket from the OEM panel and place it on the aftermarket panel. STEP 9 Panel Preparation Remove the seven screws securing the PCB board to the panel; then remove from panel.
INSTALLATION GUIDE NOTE Panel Preparation Panel Preparation PCB: 4 BUTTON + START PCB: 3 BUTTON + START STIP 12 Panel Preparation Place the three orfour button drive-train/ ignition control trim (777 6 / 7777) into the face panel (Based on vehicle model type). NOTE: Image image of panel on right is based on three button. STEP 1 S Panel Preparation Place the OEM drive-train/ ignition control buttons (retained in Step 11) into the trim from Step 12.
INSTALLATION GUIDE SJJP 16 Panel Preparation Panel Preparation Place the back cover plate over the PCB and secure it using six screws retained in disassembly. NOTE: Use the screws attained from the OEM PCB cover plate. INSTALLATION GUIDE STEP 17 Radiotnstallation Radio Installation .:, ..."'>. Single DIN Only Attach brackets provided to the pocket (A), " then secure the radioto the brac.kets (B). Lastly, secure radio assembly into dash cavity (C) and proceed to the next step. ..
STEERING WHEEL WIRING CODES Left Screen (Cont'd) FIGURE 1A 1. Prepare SWC steering wheel connector harness by using the chart below 2. Connect the harness to the interface module. 3. For Alpine, Clarion, JVC, Panasonic and Sony car stereos, connect the 3.5mm male steering plug into the steering wheel input jack at the back of the stereo. 4. For Kenwood and newer JVC stereos, connect the BROWN wire from the steering wheel harness to the •Remote in• wire at the back of the stereo.
ITCFDOSAB WIRING DIAGRAM LEGEND FIGURE 2 WIRING DIAGRAM LEGEND A. Connect to the back of the Push-Start module B. Connect to aftermarket radio (See WIRING COLOR CODES below) C. Vehicle Speaker Wires Connector (Color codes below) * If the vehicle has Shaker Audio then the Shaker interface should be connected to Cand L should be plugged into the other end of the interface. D. Connect to vehicle factory radiochassis E. Steering Wheel Controls (See Page 7for more details) F. Connect to the back of the UAC.
ITCFDOSAB WIRING DIAGRAM FIGURE2 o e 00 G e 0 G G> For Shaker Equipped Systems Shaker interface should be ronnected • a: C a: C a: C -0 0 N ~ C 'St' -0 other end of the interface. M. Connect to aftermarket radio (See Color Codes) N. Connect to aftermarket radio's AMP remote (Blue/White) ~~ C to Cand l should be plugged into the 0.
CLIMATE & CONVENIENCE CONTROLS SINGLE ZONE Left screen The Scosche Touch Screen Interface replaces the Factory climate, convenience and personalization controls built into the Factory Ford Radio/Dash panel. This solution provides improved ergonomics while adding touch screen capabilities unique to this system. Read the following sections to familiarize yourself with the operating controls and settings. FIGURE 3 LEn TOUCHSCREEN ~[llifill ~[3 ~~ BUTION LAYOUT 1. 2. 3. 4. 5. 6. 7. 8. 9. 1o. 11.
CLIMATE & CONVENIENCE CONTROLS SINGLE ZONE LeftscreenrconrdJ TEMPERATURE CONTROL (Page 10 Fig. 3, 18-10) Use the UP and DOWN arrows (Page 10 Fig.3 #8 &110) on the color TFT touch screen to adjust vehicle air temperature.Touch the Red arrow to increase air temp. Touch the Blue arrow to decrease air temp. The temperature indicator will move up or down indicating the current temperature level. The temperature range is color-coded: Red indicates warmer air and Blue indicates cooler air.
CLIMATE & CONVENIENCE CONTROL DUAL ZONE Left screen The Scosche Touch Screen Interface replaces the Factory climate, convenience and personalization controls built into the Factory Ford Radio/Dash panel. This solution provides improved ergonomics while adding touch screen capabilities unique to this system. Read the following sections to familiarize yourself with the operating controls and settings. FIGURES LEFT TOUCHSCREEN ~~~~'um BUTION LAYOUT 1. DriverAir Temp Warm 2. Driver lemp Reading Air Temp.
CLIMATE & CONVENIENCE CONTROLS DUAL ZONE Rightsc,een FIGURE 6 RIGHT TOUCHSCREEN ~ ~llU ~IBYl\'iID'.5 BUTION LAYOUT 1. 2. 3. 4. s. 6. 7. 8. 9. ['nwrr button Air Conditioning (On/Off) f1(:c1culat1on (On/Ott) Max A'C (On/Off) rront Dr.frost (On/Off) Rrar )drost (On/Off) Irri1p. Read ng Arld1t:on Control ~1enu Sctt1n~s Menu C) * ~ Press the Power Button (Fig.6, t1) to toggle the climate controls On or Off. Press the Air Conditioning Button (Fig.6, t2) to tum On/Off the air conditioner.
CLIMATE & CONVENIENCE CONTROLS DUAL ZONE Right screen FIGURE 7 RIGHT TOUCHSCREEN [OODLiJl1 ~ [ 3 ~ ' u 1 E BUTION LAYOUT 1. Power Button 2. A/C Button 3. Jrivcr A/C (Cooled) Seat 4. Driver Heated Seat s. User Temp Preset Settings 6. 7. 8. 9. Pass. Heated Seat Pass. A/C (Cooled) Seat Return to Previous Screen Menu C) * d &} MyTemp j +l MENU ~ seas~ Time/Temp Press the Power Button (Rg.7, 11) to toggle the dimate controls On or Off. Press the Air Conditioning Button (Fig.
MENU INTERFACE NAVIGATION Press the MENU button on the display to access Configuration Menu/Vehicle/lnterface/LanguageNersion Settings. The following figures (7-9) are,5ample menu screen displays to help you navigate and understand the menu user interface f the module. Use the (Return arrow) to go back to the previous menu. Press the Xto close the menu window and return to the TFT color touch screen home screen.
Vehicle Settings TIME / DATE SETIINGS Time/ Date Feature lime SetlimeFormat Date Format Sub-Menu Option 1 Option 2 Option 3 Hours Minutes - - Minutes 0-59Min. - - Year 2000-2099 - Month 1-12 Day 1-31 - - - 12 Hr. 24Hr. - DD.MM.YY'IY MM.DD:f'r"IY YY'IY.MM.DD - D~STANCE SE1TINGS Distanc.e Feature Sub-Menu Option 1 Option 2 Option 3 Distance Units - Miles Km.
ITC/ LANGUAGE/ VERSION SETTINGS ITC SETTING$ ntSETTINGS Feature ITC Settillgs Sub-Menu Option1 Option2 Option3 Brightness (Day) 0-100% Auto - Brightness (Night) 0-100% Auto - Day/ Night / Auto Day Night Auto Touch Volume 0-100% - - Display External Temp.