By Firstech LLC Version 1.1 www.firstechllc.com www.compustar.
Introduction Thank you for purchasing a Firstech system for your vehicle. In order to truly enjoy the benefits of this system, we recommend that you thoroughly review the following manual. Please note that this manual applies to the 2WG5R-900SH 2 Way - 4 Button LED Remote, regardless of whether you purchased the alarm only, starter only or alarm/starter combination. This manual also supports the 1WG5R-900SH 1 Way remotes that may be included with your system.
Quick Reference r @m Mb @r The only regular maintenance this system requires is remote control battery replacement. No programming is required when replacing the battery. Quick Reference R@w@r @b@f Duration Function LED LED Two Way Remotes: First, remove the small Phillips screw located on the back of the remote. Once the screw has been removed, gently pull the remote apart taking care to not damage the circuit board.
Quick Reference Quick Reference R@w@r @b@f Button(s) Duration Function LED LED 2nd Car Mode Chirp(s) 0.5 second Valet mode (see Valet Mode Section for details) Amber Red Once On / Twice Off 0.5 second Drive lock. Activates ignition controlled door locks. 2.5 seconds Option programming menu 2 - Installers Only.
Wiring Diagram Notes for Wire Connection c @CQ Pin #1 : Red This wire is used as the (+)Constant Power input for the unit. This wire must be connected for the unit to function correctly. Pin #2 : Green/ White This wire is the (+)Positive Parking light output. Connect this wire directly to the (+) trigger wire generally off the parking light switch or found at or behind the fuse box. Pin #3 : Red/ White This wire is used as the (+)Constant Power input for Starter and 2nd Ignition.
Notes for Wire Connection c @C@R Pin #1 : Green/ White This is the low voltage (-) Parking light output 200mA. Some newer vehicles require a (-) parking light output instead of the standard (+) output (reference connector #1) such as the new Jeeps andeven some Fords. Pin #2 : Red/ Black This wire is a (-) 2nd Starter 200mA output. Normally the only vehicle this would be used on Nissan’s and older Ford’s. You may connect this wire to the purple pigtail of the additional relay on CN #1.
Notes for Wire Connection Remote LED Functions and Descriptions c @C@S Pin #1 : Light Blue This needs to be connected to the parking brake. This wire requires a (-) input to activate. This wire serves two functions: 1. To engage Reservation Mode for manual transmissions, reference the users or install guide. 2. To activate the Turbo Timer, reference the users or install guide. Pin #2 : Gray/ Black This is the (-) shutdown for the Hood Trigger. This wire serves two functions: 1.
Notes for Wire Connection Error Number (# of times parking lights flash) Remote LED Functions and Descriptions Tach Learning Error Diagnosis 1 Dip Switch #1 is on alternator sensing. 2 Manual Car Key is in the off position. 3 No signal or the signal is not fast enough. find a different wire ᵉ Alternator Sensing c @C@T Pin #1 : No Connection Pin #2 : Violet/ White This wire is the (-) 200mA trunk release. The following sequence takes place each time the trunk release output is triggered : 1.
Notes for Wire Connection c @C@W The is the data lines to interface Telematic Devices or Interface Modules. ᵉ Tach Learning Switch : This is the small black button on the side of the brain used to program tach. Once you have found the correct wire simply press this button while the vehicle is running and the parking light will flash once to confirm that the tach is learned. If the parking light flash three times the tach source is not valid.
Option Programming for Four Button Remotes for FM or SS Units Step1: For Programming menu 1: Press Buttons (I+II) for 2 seconds. For Programming menu 2: Press Buttons (I+IV) for 2 seconds. The car will chirp once indicating that you are in programming mode. Step2: Within a 2 seconds after pressing (I+II) or (I+IV), press Button IV the number of times to go to the option number you want to change. You have to hear a chirp and see the parking light flash each time when you press Button IV.
Option Programming with Programming Button for AM Units ᶀ Changing Factory Setting to Option Setting. #1 Step1: Turn the key to On position. (Engine Off) Step2: Press PS (Programming Switch) for two seconds until Parking Light flashes once for Option #1-1 to #1-11, then release the switch. Or, press PS for four seconds until Parking Light flashes twice for Option #2-1 to 2-10, then release the switch.
Option Programming for Six Button Remotes Programming Menu Options p@m @CQ@HaMs@@d@l@oI The procedures will be same as the 4 button remotes except the use of the different buttons. Programming 6 Button Remote 4 Button Remote ICON Feature Factory Default Optional OFF ON Programming Menu 1 (Trunk+Start)- (I+II)- Programming Menu 2 (Trunk+Stop)- (I+IV)- Option Selection (Stop)- (IV) 1-2 Door Lock / Unlock Pulse Duration 0.8 sec 2.
Programming Menu Options Note : 1-1 Some vehicles such as Mercedes-Benz and the Lexus ES300 require you to unlock the car to disarm the factory alarm before remote starting the vehicle. Activating this feature will unlock the vehicle for a brief second in order to disarm the factory alarm before auto-starting the vehicle remotely then lock after starting. 1-4 This feature unlocks the driverᴗ s side door lock with the first unlock pulse. A second unlock pulse is need to unlock the rest of the car doors.
Diagnosing Problems with Auto-Start If there is a problem in auto-starting your car, you will see three flashes of the parking lights when you attempt to auto-start the car. Wait for 2 seconds and the cause for the error, will be indicated by the number of times the parking lights flash.
