User manual

28
3.
To leave the mute state, press “Unmute” (Left) soft key.
Note: Mute is effective only for the current call. It is automatically turned off
after the call is ended.
Do Not Disturb (Silent Ring)
1. Enter the key sequence MENU – Sounds – Ring Volume, then select “Off”.
This will turn off the ringer until it is turn on again from the menu.
2. For temporary silencing the ringer when an incoming call arrives, press
Silent (Left) soft key.
Key Guard
1. To prevent accidental dialing, you can press Menu (Right) soft key, then
select Key Guard option. The handset keypad is locked. No key entry is
accepted except the power on/off key.
2. To unlock the keypad, press “Unlock” (Left) soft key, then, within 2 seconds,
press the digit “1” to unlock.
3. Key Guard is in effect until unlocked. It is still in effect after a power off-on
cycle.
Battery Recharge and Replacement
1. Charge the battery when one or several of the following happen:
a. Phone beeps 1-long-2-short every 30 seconds.
b. Battery icon is empty.
c. Phone does not respond when a key is pressed.
d. LCD and backlighting become dim.
e. Talk range shortfall is experienced.
2. You can replace the handset battery after placing the call-in-progress on
hold.
3. Battery talk time and standby time vary depending on the talk/standby
pattern and the operating distance. Putting the handset back to charger
cradle as often as possible is recommended for best performance.
Note: Use only manufacturer provided batteries and charger.
29
Advanced Operations
Handset Registration
1. If your handset(s) is purchased as part of a system, it has been pre-
registered with the base station at the factory.
2. You need to register the handset with the base station in the following
situations:
a. If a handset displays a Handset ID “00,” that means it is a new handset
or the ID has been erased.
b. In certain situations, you may want to change a handset’s ID. For
example, you want to change a particular handset from a user to an
administrator (ID 10 or 11), or vice versa. Or in some rare occasions,
you find another handset having the same Handset ID.
3. Registration:
a. Press handset Menu (Right) soft key.
b. Press the number “8” to enter the handset registration menu.
c. Press and hold the base’s Registration (REG) button for 2 seconds until
the L1, L2, L3, and L4 LED come on.
d. Press handset key “1”, this completes the registration process. The
base station will assign a handset ID between 10 and 99. The assigned
ID will be displayed on the handset LCD, indicating successful
registration.
e. Repeat above steps for all additional handsets.
f. The first two handsets registered will be given ID 10 and 11, which gives
them administrator privileges.
4. De-registration:
a. You can de-register a handset from a base. De-registration will reset
the Handset ID to 00, erase the system security code on the handset,
and free up the old ID for future registration.
b. After deregistration, the handset will not be able to use the base to
make or receive phone calls, nor can it intercom other handsets.
c. Press handset Menu (Right) soft key.
d. Press the handset number key “8” to enter the handset registration
menu.
e. Press and hold the base’s REG button for 2 seconds until L1, L2, L3,
and L4 LED come on.
f. Press the handset number key “2”, this completes the de-registration
process. Upon successful de-registration, the handset will show ID “00”.
Notes:
a. The base has a 30 second registration timeout starting from pressing
the REG button. The handset has a 12 second registration timeout
starting from the registration or de-registration option has been
selected. The base and handset will automatically exit registration