User Manual

ManualsBrandsSentry Industries ManualsAudio EquipmentBluetooth Headset

User Manual

Bluetooth Headset

BT250

FCC ID:2ACP4BT250

Product Parameters

型号

Model

BT250

使用距离

Use

Distance

10 米

10 m

版本

Version

V4.1

电池容量

Battery

Capacity

55mAH

待机时间

Stand-by Time

180 小时

180 hours

通话时间

Talk Time

4.5 小时

4.5 hours

电源输入

Power Input

DC5V/200mA

充电时间

Charging

Time

2 小时

2 hours

降噪

Noise Reduction

CVC6.0

协议

Protocol

HFP HSP A2DP AVRCP APTX

切歌

Skip

支持

Support

语音提示

Voice

Prompt

支持

Support

功能

Function

来电报号，线控接听/挂断/拒接/开关机，电话重拨，音量调节，中

英文切换，智能一拖二，听音乐暂停/播放，上下切换歌曲

Caller report, line control answer/hang up/rejection/on-off, redial,

volume adjustment, Chinese-English shifting, intelligent one-driving-

two, music pause/play, up and down song switching

产品应用

Product Application

支持任何带蓝牙设备类型的手机，ipad 平板电脑，台式电脑。不自

带蓝牙功能的台式电脑可配合蓝牙适配器使用。

Support any mobile phones with Bluetooth device, iPad and desktop

computer. The desktop computer without Bluetooth function can be used

by matching with the Bluetooth adapter.

配对与连接

Pairing and Connection

1 使手机与耳机的距离保持在一米以内，越近越好。

1. Keep the distance between the mobile phone and the headset within 1 m; the closer, the better.

2 按住“ ” 键约 5 秒看到红蓝灯交替闪烁时松开，此时耳机已进入配对模式。

2. Press and hold the key for about 5 seconds, and then release it when the red and the blue

lamps alternately blink. At this time, the headset has entered the paring mode.

3 开启手机蓝牙功能，搜索蓝牙设备，选择‘BT250’ 序号名即可配对连接，当连接成功后，

耳机蓝色指示灯慢闪

3. Enable the Bluetooth function of the mobile phone, search the Bluetooth equipment, select

‘BT250’ sequence name for paring and connection. After connection is successful, the blue

indicating lamp of the headset slowly blinks.

注意：

Notes:

若手机提示输入配对密码，请输入‘0000’并确认

If the mobile phone prompts to enter the pairing password, please enter ‘0000’ and confirm.

配对模素会维持 5 分钟，超过 2 分钟仍未成功配对连接时，耳机会自动切换到待机模式

The pairing mode will be maintained for 5 minutes. If pairing and connection are unsuccessful

beyond 2 minutes, the headset will automatically switch to the stand-by mode.

完成配对后，耳机和手机会相互记住对方，下次使用时无需再次配对。耳机再次开机

After pairing iscompleted, the headset and the handset will remember eachother, without pairing

Summary of content (4 pages)

PAGE 1
User Manual Bluetooth Headset BT250 FCC ID:2ACP4BT250 Product Parameters 型号 Model 版本 Version 待机时间 Stand-by Time 电源输入 Power Input 降噪 Noise Reduction 切歌 Skip 功能 Function 产品应用 Product Application 使用距离 10 米 Use 10 m Distance V4.1 55mAH 电池容量 Battery Capacity 180 小时通话时间 4.5 小时 180 hours Talk Time 4.5 hours DC5V/200mA 充电时间 2 小时 Charging 2 hours Time CVC6.
PAGE 2
线控器按键功能 Key functions of line controller （随手机品牌，型号，系统版本不同而有所差异，请消费者自行验证，恕不一一列举） (Vary with the brand, mode and system version of the mobile phone. The consumers shall make verification by themselves.) 在开/关机:长按“ ”键 5 秒开/关机 On/off: Press and hold the key for 5 seconds to turn on/off. 暂停音乐或视频：短按“ ”键暂停播放，再按一下恢复播放 Music or video pause: Press the key to pause playing, and press the key again to resume playback.
PAGE 3
Step III: connect the first mobile phone with the headset again 1.打开手机 A 的蓝牙功能 1. Enable the Bluetooth function of the mobile phone A. 2.找到手机蓝牙菜单下，之前连接过的‘BT250’序号名记录，重新点击连接 2. Find out the record of ‘BT250’ sequence name’previously connected under the Bluetooth menu of the mobile phone, and then click “Connect” again. 3.至此手机 A，手机 B 同时连接上蓝牙耳机 3. At this point, the mobile phone A and the mobile phone B are simultaneously connected to the Bluetooth headset.
PAGE 4
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.