BB- II -10-E Z-ray II Instruction Manual IMPORTANT SAFETY GUIDLINES FOR SPORT BOAT USE Please read & understand prior to using your boat 1
TABLE OF CONTENTS Introduction ……….……...…………..…….……………..…….… 3 Important Safety Guideline …….……..…….…………………..… 4-5 Sketch Map ………...……………………………………………… 6 Information (Basic data & Accessories)………..……..…………… 7 Installation Illustration …………...........…………………………... 8-11 Operating instructions ………...................………………………… 12-13 General Maintenance ..................................……………………… ..14 Disassembly ………………..……………………………………… 14 Repairs ………………..…………………………………………… 15 Trouble Shooting Guide …………………………...
Introduction We thank you for your purchase of our Z-ray II series. We think you will find it quite simple to install and use efficiently. Please read the following instruction carefully before using this inflatable boat and keep the instruction for future reference. If you re-sell the craft, please hand this manual over to the new buyer. ThisZ-ray II inflatable boat has been manufactured to the highest quality standards.
Important Safety Guideline Please read & understand prior to using boat To enhance the enjoyment of your boat and protect the safety of the operator using the product, ALWAYS STRICTLY OBSERVE the following important safety points. These should be read and understood prior to use: 1. WARNING: Boat designed for voyages in sheltered water only. Please only use the craft on small lakes, rivers and canals where conditions up to a wind force of level 4 and wave height up to 0.5m. 2.
8. WARNING: Beware of offshore winds and under-currents. These could be unsafe conditions. 9. WARNING: The total number of persons and total weight shall not exceed the information printed on the boat. Do not exceed the maximum recommended capacities. Overloading violates regulations 10. WARNING: It is the responsibility of the boat operator to identify and obey all local and state laws pertaining to boat safety and required safety equipment. Please consult your local authorities to ensure compliance.
Sketch Map High Strengh Nylon Safecy Grab Rope High Pressure Valve Quick Assembly Wooden Bench Seat System PVC-Anti-Bump Protective Strake Heavy Duty PVC Swivel Oarlock Durable And Stronge Aluminum Floor Board Drain Valve Compliance Plate Marine Ply Motor Transom Carring Handle PVC Cpne 6
Basic data Item No. JL007013-2N Z-ray II Model No. 500 365 x 205cm (144˝ x 81˝) Deflated Size Inflatable Size Max. Power of motor Capacity (Person) Max. Load Weight(kg) 360 x 170 x 44cm (142˝ x 67˝ x 17.5˝) 9.9 HP 7.4 kw 5 600 kg 1321 Lbs Accessories Ref.
Installation 1. Find a flat area and make sure that the surface you have selected to set up the boat is completely free of stones, sticks, sharp objects or other foreign debris. 2. Carefully unfold the boat, spreading out the tubes and floor to make them as smooth as possible. NOTE: For ease of install, it is preferable to set up the boat on a warm and sunny day.
4. Wooden bench seat installation: Insert the plastic (or wooden) rods into the seat retaining tubes (E). Side the seat into position by inserting the retaining tubes into the grooves located at each end of bench seat. Insert into both ends of the seat at the same time (F) and (G). Position the seat to be in the middle of the retaining tubes. 5. Inflate the boat’s chambers in numbered sequences (1) and (2) then (3), (4).
a) Inflation: Unscrew the Valve Cap A, Assemble the Inflation Adaptor with the Inflating Mouth B, Air pressure Meter and the air pump (Please see the below detailed illustration!). Air Pressure Meter Assembled with Assembled with Inflating Mouth B Air Pump After the inflation adapter is assembled completely, you can inflate the boat by number sequence. Do not over inflate. After inflating, screw the Valve Cap A in clockwise direction by hand. Caution: Do not over inflate or use high-pressure pump.
。 counter-clockwise direction by 90 . The deflation will stop when the valve is released. 6. Oars Assembly: Assemble the section of the oar by depressing the spring loaded pin and inserting the sections of oar until the pins lock into their retaining holes. 7. Oars Installation: Insert the bolt on the swivel oarlock into the central hole on the oar shaft. Screw the retaining nut onto the end of the bolt and position the oar into the oar holder. 8.
Operating Instruction I) Preparation before departing: 1. Acquire necessary information and inform other passengers: A) Get information on local laws, regulation and hazards related to water activities and boat operation. B) Check weather forecast, local currents, tides and wind conditions. C) Advise someone on land of the time you plan to be back. D) Explain basic boat operation to all passengers. E) Be sure that at least one of your passengers can operate the boat in case of emergency.
II) Rules to observe during navigation: 1. Be responsible and strictly follow the safety rules. Do not neglect the safety rules. This could hazard your life and the lives of other passengers. 2. Learn to always keep control of your boat. 3. Respect local regulations and practices. 4. Remember weather conditions can rapidly deteriorate. Always be sure that you can reach a shelter rapidly. 5. Each person on boat always wears a personal flotation device. 6.
General Maintenance 1. Depending on the parts usage, keep some spare available, all parts suggest must consult local agent for factory authorized parts when servicing system. 2. Clean your boat after a trip to prevent damage from sand, salt water or such exposure. 3. No lubrication or regular mechanical maintenance is needed. 4. Wash outside of the boat with a mild detergent and water, or use the sponge and mild soap. It can clean most dirt. 5.
Repairs Little holes or punctures can be repaired with the repair kit come along with the boat. 1. Find the leak on the boat first. 2. Thoroughly clean the area surrounding the leak to remove any dirt or grime. 3. Cutting a piece of repair material in round shape, that should be larger than the damaged area. 4. Using a pencil, trace the outline of the patch lightly. 5. Apply adhesive to the underneath side of the patch and around the area to be repaired.
LIMITED WARRANTY ATTENTION CUSTOMER - Please read this statement carefully and keeps your original store receipt along with this warranty certificate at all times. Your receipt is required as proof of purchase and to verify the length of your product ownership. We warrant all components contained in this product against defects in materials and workmanship under normal use and service, for a period of 730 days from the date of purchase for the original owner only.
