Operating instructions
Using a PC
RS-232C Port Specifications
When "?"
is
input for some
commands, the
present setting
value responds.
7
/~
Command 4-digits Parameter 4-digits Return code
Command 4-digits: Command. The text of four characters.
Parameter 4-digits: Parameter
0-9,
x,
blank, ?
• Parameter
Input the parameter values, aligning left, and
fill
with
blank(s) for the remainder. (Be sure that 4 values are
input for the parameter.)
When the input parameter
is
not within
an
adjustable
range,
"ERR"
returns. (Refer to "Response code format".)
Any numerical value can replace the "x" on the table.
• Command format
Eight
ASCII
codes +
CR
~
~
L:TIIITJ
• Response code format
Normal response Problem response (communication
~
error or incorrect command)
~
~
~
Return code
(ODH)
~
Return code
(ODH)
None
None
8 bits
1 bit
9,600 bps
;ao,l
• Communication procedure
Send the control commands from the
PC
via
the
RS-
232C connector.
The
1V
operates according to the received command
and sends a response message to the
PC.
Do
not send multiple commands at the same time.
Wait until the
PC
receives the OK response before
sending the next command.
• Command table
• Commands not indicated here are not guaranteed to operate.
• PC control of the TV
• Attach
an
RS-232C cable cross-type (commercially
available)
to
the supplied Din/D-Sub RS-232C for the
connections.
mm
• This operation system should be used by a person who
is
accustomed to using computers.
• Communication conditions
Set the RS-232C communication settings on the PC to
match the
1V's
communication conditions.
The
1V's
communication settings are as follows:
CONTROL ITEM
COMMAND
PARAMETER
CONTROL CONTENTS
POWER ON COMMAND SETTING
R:
S , P
:w
1-'0,-,-"
_=-,,-,:
_~''-=-1f''0",ff
-+T",h:::.e.:,.Po",w-,-,e,,-r
O",-n"-c",o",m",rna"""nd",r""e'",ec,,,ted=-.
---------------1
. ,
~
1:
: : On The Power On command accepted.
POWER SETTING P
'0
'w' R
0·
_'
, Power Off
It
shiffs
to
standby.
1-,'-'""':
=-+'=-+'O-f=p-"-ow-e'--r-=O-n------------+P=-'o'--w--'er'-:O"'n..:..cc--'-'-"----------------------1
INPUT SELECTION A TOGGLE I
~
T
~
G : D x
~
(Tooole)
It
inout-switches by the toggle.
It
is the same as an input change
key)
lV
I : T : V :
DO:
_ ' _
It
input-switches to
lV,
(A
channel remains as it is, (Last memory))
INPUTl-8
I:
A : V : D _ Input terminal number (1-8)
It
input-switches to INPUT1-INPUT8.
INPUT SELECTION B
f"IN-::P""U=T_=l--+I'--'--'N'-'~_=P--'~_=l+---'-=---'-=~+:-'O:.:.,A=ut:.::O.:,.,
1:,:.:
.:.,VI""D:=;EO",.-=Z,:,,:
C=O",M",P--,O",N:.:::E:::N=-T
,.,.,..,.,..,-----1An input change
is
also included.
INPUT Z I
,N,
P , 2
0:
Auto, 2: COMPONENT,
3:
S-TERMINAL
AV
MODE SELECTION A
~
V
,M
~
D , _ : _
,_
0:
(Toggle),
1:
STANDARD,
2:
MOVIE,
3:
GAME.
4:
USER,
5:
DYNAMIC
(Fixed),
6:
DYNAMIC,
7:
PC.
100:
AUTO
Although it can choose now, it
is
toggle operation
in
inside.
VOLUME
V'O'L'M
:.
:
Volume (0-60)
POSITION
H-POSITION
H:
P : 0 : S
.,
The screen position variable ranges depend on the View Mode or the
I-V'-:_P"cO::.,:S"'IT"cIO::..cN-+'-V"",f-'-P...;,-=O'-+,-=S+--+--+--+-=+---------------lsignal
type. The ranges can be seen on the position-setting screen.
CLOCK
C,L,C,K
. _ Onlv PC mode.
(0-
180)
PHASE P , H ' S : E Only PC mode, (0-40)
VIEW MODE
WID
E
0:
(Toggle)
(AV],
1:
Side Bar
(AV],
2:
S,Stretch
IAV]
3: Zoom
IAV].
4:
Stretch
[AV].
5:
Normal [PC]
6: Zoom
[PC).
7:
Stretch [PC].
8: Dot by Dot (PC]
(AV].
9: Full Screen
[AV]
0: Although it can choose now, it
is
toggle operation in inside.
1:
Only available when 4:3 signal is being input.
5.
6:
Only available when 4:3 signal
is
being input.
8: [PC] Available except when UXGA is being input.
IAV]
Only available when I0B0Vp is being input.
9: Only available when 720p is being input.
If
it is not
lV
displav, it will input-switch
to
lV,
(same function as
CHV)
DIGITAL Cable (Two-Part numbers. 3-digit plus 3-digit)
Front half of DIGITAL CABLE CHANNEL NO, (Desianate rna'or
channeQ
If
it is not
lV
display.
it
will input-switch to
lV,
(same function as
CH/\)
DIGITAL Cable (One-Part numbers 5-diQrt. less than 10,0001
DIGITAL Air wo-Part numbers. 2-di it olus 2-di
it
DIGITAL Cable One-Part numbers, 5-diait. more than 10.0001
DIGITAL Cable (Two-Part numbers. 3-digit plus 3-digit)
Rear half of DIGITAL CABLE CHANNEL NO, (Designate minor channel)
An
input change
is
included if
it
IS
not TV display.
In
Air,
2-69ch
is
effective.
In
Cable, 1-13Sch
is
effective.
The
channel
number
of
lV
-1
(0-6383)
The channel number of 1V +1
(0-9999)
(0-999)
The channel number of TV
(1-135)
0:
Off.
1:
OFF
TIMER
-
30
MIN
.•
2:
OFF
TIMER
-
60
MIN
..
3:
OFF
TIMER
- 90
MIN
..
4:
OFF
TIMER
-
'20
MIN.
0: (Toggle). 1: On.
2:
Off
0: (Toggle).
1:
On.
2:
Off
(Toqgle)
-
-:-
x:
:
.:
: :
C:H:O:W
x:
A:C:S:U
D:C~C~H
M'U,T'E
CHDOWN
DIRECT
CHANNEL
(DIGITAL)
DIRECT
CHANNEL
(ANALOG)
CHUP
MUTE
AUDIO SELECTION
SLEEP TIMER
SURROUND
CHANNEL
CC
(Tooole) Toaale operation of a closed caotion.
ImD
• If
an
underbar U appears
in
the parameter column, enter a space.
• If
an
asterisk
(*)
appears, enter a value
in
the range indicated
in
brackets under CONTROL CONTENTS.
• Any numerical value can replace the "x" on the table.
@-
41