AN KS1 CZZ MODEL AR-C260 AR-C260M DIGITAL FULL COLOR COPIER/PRINTER (AR-C260) DIGITAL FULL COLOR MULTIFUNCTIONAL SYSTEM (AR-C260M) OPERATION MANUAL (for general information and copier operation) Page • BEFORE USING THE PRODUCT • MANAGING THE MACHINE • PERIPHERAL DEVICES • BEFORE MAKING COPIES • BASIC PROCEDURE FOR MAKING COPIES • CONVENIENT COPY FUNCTIONS • MACHINE MAINTENANCE (FOR COPYING) • SPECIFICATIONS 1-1 2-1 3-1 4-1 5-1 6-1 7-1 8-1 Be sure to become thoroughly familiar with this manual to gain
00-08.book 1 ページ 2002年11月8日 金曜日 午前9時39分 The power switch positions are marked " I " to indicate power "ON" and " " to indicate stand-by. In the stand-by position, power is being supplied to a drying heater within the optical system of the copier. Caution: For complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. FOR YOUR RECORDS ...
00-08.
00-08.
00-08.book 1 ページ 2002年11月8日 金曜日 午前9時39分 NOTES ● Considerable care has been taken in preparing this manual. If you have any comments or concerns about the manual, please contact your nearest SHARP Service Department. ● This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect or other problem is discovered, please contact your dealer or nearest SHARP Service Department.
00-08.book 2 ページ 2002年11月8日 金曜日 午前9時39分 INSTALLATION REQUIREMENTS Improper installation may damage this product. Please note the following during initial installation and whenever the machine is moved. 1. The machine should be installed near an accessible power outlet for easy connection. 2. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded.
00-08.book 3 ページ 2002年11月8日 金曜日 午前9時39分 INSTALLATION REQUIREMENTS Moving this machine Pull out the four handles as shown below, grasp them firmly, and keep the machine horizontal while moving it. Left side Exit tray Handles Before lifting the machine, fold up the exit tray and tape it securely to the machine. Right side Bypass tray Handles Before lifting the machine, fold up the bypass tray and tape it securely to the machine. Caution Two people are required to lift and carry this machine.
00-08.book 4 ページ 2002年11月8日 金曜日 午前9時39分 CAUTIONS 1. Do not touch the photoconductive drum. Scratches or smudges on the drum will cause dirty prints. 2. The fusing unit is extremely hot. Exercise care in this area. 3. Do not look directly at the light source. Doing so may damage your eyes. Fusing unit 4. Four adjusters are provided on all optional stand/ paper drawer units. These adjusters should be lowered until they contact the floor.
00-08.book 5 ページ 2002年11月8日 金曜日 午前9時39分 CONTENTS PRODUCT CONFIGURATIONS.....................................0-1 OPERATION MANUALS.................................................0-1 INSTALLATION REQUIREMENTS.................................0-2 ● Moving this machine ....................................................0-3 CAUTIONS......................................................................0-4 CHAPTER 1 BEFORE USING THE PRODUCT INTRODUCTION........................................................
00-08.book 6 ページ 2002年11月8日 金曜日 午前9時39分 CONTENTS CHAPTER 4 BEFORE MAKING COPIES ● Pamphlet copy........................................................... 6-25 JOB PROGRAM MEMORY .......................................... 6-26 ● Storing a job program ................................................ 6-26 ● Recalling a job program ............................................ 6-27 ● Deleting a stored job program ................................... 6-27 INTERRUPTING A COPY RUN ............................
00-08.book 1 ページ 2002年11月8日 金曜日 午前9時39分 CHAPTER 1 BEFORE USING THE PRODUCT This chapter contains basic information that should be read before using the product. Page INTRODUCTION ...........................................................................................1-2 MAIN FEATURES ..........................................................................................1-2 PART NAMES AND FUNCTIONS .................................................................1-4 ● Exterior.....................
00-08.book 2 ページ 2002年11月8日 金曜日 午前9時39分 INTRODUCTION To gain the maximum benefits in using this product, it is recommended that the user read this manual to become familiar with all the features and functions of the basic product and the precautionary information contained in the manual. This product is a high speed Digital full color copier / printer that can be expanded to become multifunctional through the installation of optional peripheral devices.
00-08.book 3 ページ 2002年11月8日 金曜日 午前9時39分 MAIN FEATURES 2 A range of optional units to enhance productivity A range of optional equipment is available to enhance productivity, such as duplex units for producing two-sided output, additional paper feed units to increase the number of available paper sizes and paper capacity, and paper output units that are capable of stapling and saddle stitch binding.
00-08.book 4 ページ 2002年11月8日 金曜日 午前9時39分 PART NAMES AND FUNCTIONS Exterior Without the duplex bypass/inverter unit installed. Left tray (See page 5-5) Bypass tray Finished sheets are deposited here. Left side cover Special papers (including transparency film) and copy paper can be fed from the bypass tray. Stand/1 x 500 sheet paper drawer * (See page 2- Open this cover when a paper misfeed occurs in the fusing unit or the transfer unit.
00-08.book 5 ページ 2002年11月8日 金曜日 午前9時39分 PART NAMES AND FUNCTIONS Interior 1 Fusing unit Toner cartridge Toner images are fused here. The toner cartridge must be replaced when indicated on the operation panel. (See page 2-15) Right side cover CAUTION The fusing unit is hot. Take care in removing misfed paper. Open when a misfeed has occurred in the paper feed area. Right cover of paper drawer Open this cover to remove paper misfed in the paper drawer.
00-08.book 6 ページ 2002年11月8日 金曜日 午前9時39分 PART NAMES AND FUNCTIONS Part names and functions of peripheral devices Reversing automatic document feeder (AR-RF3) Stand/3 x 500 sheet paper drawer (AR-D18) This automatically feeds originals to be scanned. The feeder can turn the original over and scan the back side as well as the front side for support of two-sided originals. This stand has three paper trays. Each tray can hold approximately 500 sheets of the recommended paper for color (20 lbs.
sec_whale_01_1.fm 7 ページ 2002年11月13日 水曜日 午前8時46分 PART NAMES AND FUNCTIONS ■ Other optional equipment Peripheral equipment used when the machine is connected as a computer printer ● Print controller (AR-P16) This is required to add printing or network scanning capability to a machine not equipped for printing as standard. This board also functions as a printer controller that is required for use of the network scanner function.
00-08.book 8 ページ 2002年11月8日 金曜日 午前9時39分 PART NAMES AND FUNCTIONS Operation panel Touch panel Numeric keys The machine status, messages and touch keys are displayed on the panel. The display will change to show the status of printing, copying or network scanning according to which mode is selected. For details see the next page. Use to enter number values for various settings. Mode select keys and indicators [#/P] key Use to change modes and the corresponding display on the touch panel.
00-08.book 9 ページ 2002年11月8日 金曜日 午前9時39分 PART NAMES AND FUNCTIONS Touch panel Using the touch panel Selection of function [Example 1] [Example 1] JOB QUEUE COPY SETS / PRO 003 / 00 SHARP001 003 / 00 0666211221 010 / 00 Beep tone Items on the touch panel are easily selectable by touching the key associated with the item with a finger. Selection of an item will be accompanied with a beep tone to confirm the item was selected.
sec_whale_01_1.fm 10 ページ 2002年11月13日 水曜日 午後10時3分 PART NAMES AND FUNCTIONS Job status screen (common to print, copy and network scan) This screen is displayed when the [JOB STATUS] key on the operation panel is pressed. A job list showing the current job at the top of the job queue or a list showing completed jobs can be displayed. The contents of jobs can be viewed or jobs can be deleted from the queue.
00-08.book 11 ページ 2002年11月8日 金曜日 午前9時39分 AUDITING MODE When the account counter function is turned on, a count is kept of the number of copy sheets used by each account (maximum of 200 accounts). The counts can be displayed and totaled as needed. "A key operator program can be used to enable the auditing mode individually for the copy, network scanner or the printer modes.
00-08.book 12 ページ 2002年11月8日 金曜日 午前9時39分 AUDITING MODE your account number (5 digits) with 1 Enter the numeric keys. the appropriate steps to perform 2 Follow the copy job. As you enter your account number, the hyphens ( ) change to asterisks ( ). If you enter an incorrect digit, press the key and reenter the correct digit. When a correct account number is entered, the following message will appear. When copying is begun, the following message will appear.
00-08.book 1 ページ 2002年11月8日 金曜日 午前9時39分 CHAPTER 2 MANAGING THE MACHINE This chapter explains how to load paper, replace the toner cartridge, and remove paper misfeeds. It also contains information about supplies. Page LOADING PAPER..........................................................................................2-2 ● Loading paper in paper tray 1 ................................................................2-2 ● Changing the paper size in paper tray 1 ........................................
00-08.book 2 ページ 2002年11月8日 金曜日 午前9時39分 LOADING PAPER The message "ADD PAPER" or "OPEN TRAY AND ADD PAPER" will appear when paper runs out during operation. Follow the procedure below to load paper. NOTES ● Do not use curled or folded paper. Doing so may cause a misfeed. ● For best results use paper supplied by SHARP. (See pages 2-9, 2-17.) ● When you change the paper type and size in paper tray 1, you must change the paper type and size settings as explained in "Setting the paper type" (page 2-11).
00-08.book 3 ページ 2002年11月8日 金曜日 午前9時39分 LOADING PAPER 4 Load paper into the tray. the paper type of the paper that was 6 Set loaded in the 1st tray. If you loaded a different type of paper from the previous paper, be sure to set the new paper type as explained in "Setting the paper type" (page 211). paper size in paper tray 1 is now 7 Changing complete. 2 5 Gently push tray 1 into the machine. Push the tray firmly all the way into the machine.
00-08.book 4 ページ 2002年11月8日 金曜日 午前9時39分 LOADING PAPER Loading paper in the bypass tray The bypass tray can be used to feed the same paper specified for paper tray 1 or for special papers. For paper types that can be used in the bypass tray, see the specifications for the bypass tray in the paper tray specifications (page 2-9). Up to 250 sheets of SHARP standard paper or up to 100 postcards can be set in the bypass tray.
00-08.book 5 ページ 2002年11月8日 金曜日 午前9時39分 LOADING PAPER NOTES ● Be sure to load 5-1/2" x 8-1/2" paper, A5 paper, and postcards as shown in the diagram below. 2 Post cards. 5-1/2" x 8-1/2" paper, A5 paper. ● When loading plain paper other than paper recommended for color, SHARP standard paper, special media other than postcards, SHARPrecommended transparency film, or paper to be printed on the back, the paper must be loaded one sheet at a time. Loading more than one sheet at a time will cause misfeeds.
00-08.book 6 ページ 2002年11月8日 金曜日 午前9時39分 LOADING PAPER ■ Setting envelopes or postcards When setting envelopes or postcards in the bypass tray, set them in the orientation shown below. Loading postcards Insert the postcard with the side to be printed on facing up. The postcard should be oriented as shown in the diagram. Loading envelopes Only the front side of envelopes can be printed. Insert the envelope with the front side facing up.
00-08.book 7 ページ 2002年11月8日 金曜日 午前9時39分 LOADING PAPER the duplex bypass/inverter unit 1 Unlatch and slide it to the left. close the duplex bypass/inverter 3 Gently unit. Unlatch the unit and gently move it away from the machine. If the machine is not equipped with a duplex bypass/ inverter unit, open the side cover similarly. If the machine is not equipped with a duplex bypass/inverter unit, close the side cover.
00-08.book 8 ページ 2002年11月8日 金曜日 午前9時39分 LOADING PAPER Loading paper in the duplex module/2 x 500 sheet paper drawer Upper tray: The upper tray contains a duplex module that automatically turns print paper over for automatic two-sided printing. Middle and lower paper trays: The middle and lower trays are paper trays. Up to 500 sheets of paper recommended for color or SHARP recommended plain paper can be loaded in these trays. The method of loading paper is the same as for paper tray 1 in the main unit.
00-08.book 9 ページ 2002年11月8日 金曜日 午前9時39分 LOADING PAPER Specifications of paper trays The specifications for the types and sizes of paper that can be loaded in the paper trays are shown below. Paper tray type A Paper tray 1 Tray No. (tray name) Applicable paper types Applicable paper sizes Remarks Paper recommended for color 11"x17", 8-1/2"x14", 8-1/2"x13", 8-1/2"x11", 8-1/2"x11"R, 5-1/2"x8-1/2", Extra.
00-08.book 10 ページ 2002年11月8日 金曜日 午前9時39分 LOADING PAPER ■ More information on plain paper The following restrictions apply to plain paper. Be sure to load the paper correctly. Incorrect loading may result in skewed feeding or misfeeds. Plain paper SHARP paper standard Restrictions on paper other than SHARP standard paper Paper in inch system Paper in AB system 5-1/2"x8-1/2" - 12"x18" A5 - A3W 20 lbs. 80g/m2 17 to 28 lbs.
00-08.book 11 ページ 2002年11月8日 金曜日 午前9時39分 LOADING PAPER Setting the paper type (except the bypass tray) Setting the paper size when an extra size is loaded Follow these steps to change the paper type setting when the paper type has been changed in a paper tray. For the paper types that can be used in each tray, see page 2-9. To change the paper type setting for the bypass tray, see page 2-12. When a paper tray is set to "extra", this informs the machine that an extra size is being used.
00-08.book 12 ページ 2002年11月8日 金曜日 午前9時39分 LOADING PAPER Setting the paper type and paper size in the bypass tray Follow the steps below to set the type and size of the paper loaded in the bypass tray. 1 Touch the [PAPER SELECT] key. (When copy mode is selected) Touch the [PAPER SELECT] key in the AUTO 8½x11 main screen of the copy PAPER SELECT mode. [HEAVY PAPER 1] 3 Touch PAPER 2], and go to step 6. HEAVY PAPER1 28+lbs. 54 lbs. HEAVY PAPER2 54+lbs. 80 lbs.
sec_whale_02-1.fm 13 ページ 2002年11月13日 水曜日 午後10時18分 CUSTOM SETTINGS The items that can be set with the custom settings are shown below. ● Total count ................................... The number of pages processed by the machine and optional equipment can be displayed. (See page 2-14.) ● Display contrast ........................... Used to adjust the contrast of the operation panel display. (See page 2-14.) ● List print*1 ..................................... Used to print a list of machine settings.
00-08.book 14 ページ 2002年11月8日 金曜日 午前9時39分 CUSTOM SETTINGS the year, month, day, hour or 3 Touch minute key, and then use the or key to adjust the setting. If you select a non-existent date (for example, Feb. 30), the [OK] key will gray out to prevent entry of the date. 4 Touch the [OK] key. finish the setting operation, touch the 5 To [EXIT] key.
sec_whale_02-2.fm 15 ページ 2002年12月2日 月曜日 午後4時41分 REPLACING THE TONER CARTRIDGES When toner runs low, "[ ] TONER SUPPLY IS LOW" appears in the display. Check the message to see which color of toner needs replacement, and then promptly obtain a replacement toner cartridge. READY TO COPY. ([ ]TONER SUPPLY IS LOW.) Promptly obtain a replacement toner cartridge. If you continue to use the toner cartridge, the toner will eventually run out, the machine will stop and the following message will appear.
sec_whale_02-2.fm 16 ページ 2002年12月2日 月曜日 午後4時41分 REPLACING THE TONER CARTRIDGES the protective material from the 5 Remove new toner cartridge. 8 Return the cartridge lock lever. 9 Close the front cover. 6 Insert the new toner cartridge. Align the insert holes as shown and then push the cartridge in. NOTE A toner cartridge of a different color cannot be installed. For instance, a yellow cartridge cannot be installed in the cyan position. the cartridge in until it locks securely 7 Push in place.
00-08.book 17 ページ 2002年11月8日 金曜日 午前9時39分 STORAGE OF SUPPLIES Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for the finisher. For best copying results, be sure to use only Sharp Genuine Supplies which are designed, engineered, and tested to maximize the life and performance of Sharp products. Look for the Genuine Supplies label on the toner package. GENUINE SUPPLIES 2 ■ Proper storage 1.
sec_whale_02-2.fm 18 ページ 2002年11月13日 水曜日 午後10時2分 MISFEED REMOVAL When a misfeed has occurred during printing, the message "MISFEED HAS OCCURRED." will appear in the touch panel display of the operation panel and printing output will stop.The approximate locations of possible misfeeds are indicated by " " in the illustration below. The page numbers for detailed information for misfeed removal for each are also shown.
sec_whale_02-2.fm 19 ページ 2002年11月13日 水曜日 午後8時4分 MISFEED REMOVAL Misfeed in the paper feed area NOTE Paper misfed from a paper tray may be extending out of the tray into the right side cover area. In this case if the tray is drawn out of the machine, the paper may become torn and difficult to remove. To prevent this from happening, always open the right side cover first and remove the misfed paper if it is extending into that area. Misfeed in the 500 sheet paper drawer 1 Open the upper side cover.
00-08.book 20 ページ 2002年11月8日 金曜日 午前9時39分 MISFEED REMOVAL Misfeed in the transport area, fusing area, and exit area Transport area 1 Fusing area Open the upper side cover and check for a misfeed. 1 Open the duplex bypass/inverter unit. Grasp the finger hold and gently open the unit. Grasp the finger hold and gently open the cover. NOTE If paper is loaded in the bypass tray, temporarily remove the paper and close the bypass tray before opening the side cover.
00-08.book 21 ページ 2002年11月8日 金曜日 午前9時39分 MISFEED REMOVAL Misfeed in the stand/1 x 500 sheet paper drawer NOTE Paper misfed from a paper tray may be extending out of the tray into the right side cover area. In this case if the tray is drawn out of the machine, the paper may become torn and difficult to remove. To prevent this from happening, always open the right side cover first and remove the misfed paper if it is extending into that area. 1 Open the upper and lower side covers.
00-08.book 22 ページ 2002年11月8日 金曜日 午前9時39分 MISFEED REMOVAL Misfeed in the duplex bypass/inverter unit and duplex module/2 x 500 sheet paper drawer NOTE Paper misfed from a paper tray may be extending out of the tray into the right side cover area. In this case if the tray is drawn out of the machine, the paper may become torn and difficult to remove. To prevent this from happening, always open the right side cover first and remove the misfed paper if it is extending into that area.
00-08.book 23 ページ 2002年11月8日 金曜日 午前9時39分 MISFEED REMOVAL the misfed paper from the duplex 10 Remove module. Be careful not to tear the misfed paper during removal. ■ Misfeed in the upper or lower tray To remove misfed paper from the upper tray or lower tray, follow steps 1 through 5 of "Misfeed in the stand/1 x 500 sheet paper drawer" on page 221. 2 11 Gently close the duplex module. Push the tray firmly all the way into the machine. close the duplex bypass /inverter 12 Gently unit.
00-08.book 24 ページ 2002年11月8日 金曜日 午前9時39分 TROUBLESHOOTING Problems related to general functions of the machine are described in this section. For problems related specifically to copying, see page 7-4. For problems related to network scanner functions, see the operation manual for that function. For problems related to the saddle stitch finisher refer to page 3-12 of this manual.
00-08.book 25 ページ 2002年11月8日 金曜日 午前9時39分 TROUBLESHOOTING Problem Check Solution or cause The displayed paper size differs from the loaded paper size. The display of the tray's paper size slide differs from the paper size in the tray. When you change the paper size in the tray, be sure to adjust the paper size slide on the tray to the new paper size.
00-08.
00-08.book 1 ページ 2002年11月8日 金曜日 午前9時39分 CHAPTER 3 PERIPHERAL DEVICES This chapter explains procedures for using the Saddle Stitch Finisher (AR-F13) and Large Capacity Tray (AR-LC5). Page SADDLE STITCH FINISHER .........................................................................3-2 ● Part names.............................................................................................3-2 ● Specifications .........................................................................................
00-08.book 2 ページ 2002年11月8日 金曜日 午前9時39分 SADDLE STITCH FINISHER The saddle stitch finisher can automatically place two staples for centerline binding of prints or copies and fold them along the centerline. An optional hole punching unit is available for installation into the finisher. Part names Stapler compiler Paper to be stapled is stacked temporarily. When printing on post cards or envelopes, remove the output from here. Offset tray Output which is stapled or offset will be delivered to this tray.
00-08.book 3 ページ 2002年11月8日 金曜日 午前9時39分 SADDLE STITCH FINISHER Upper tray: Page weight Lower tray 17 to 80 lbs. or 64 to 300 g/m2 for face up output 17 to 54 lbs. or 64 to 200 g/m2 for face down output 17 to 28 lbs.
00-08.book 4 ページ 2002年11月8日 金曜日 午前9時39分 SADDLE STITCH FINISHER Saddle stitch finisher functions ■ Sort mode Sorted sets will be delivered. Original Printouts ■ Group mode Groups of copies of the same page will be delivered. Original Printouts ■ Offset mode Offset mode Non-offset mode Sets will move from side to side so that each set or group will be offset from the previous set or group for easy separation. (The offset function only operates in the offset tray.) Stapled sets will not be offset.
00-08.book 5 ページ 2002年11月8日 金曜日 午前9時39分 SADDLE STITCH FINISHER ■ Saddle stitch function The saddle stitch finisher can automatically place two staples for centerline binding of prints or copies and fold them along the centerline. 6 4 2 7 9 11 ■ Hole punching (only if a punch module is installed) If the saddle stitch finisher is equipped with a hole punch module, printed paper can be hole punched and delivered to the offset tray.
00-08.book 6 ページ 2002年11月8日 金曜日 午前9時39分 SADDLE STITCH FINISHER Using the saddle stitch finisher Touch the [Output] key on the main screen of copy mode to display the screen that allows selection of sort, staple sort, centerline stapling, group function, and the output tray. OUTPUT SORT OK OFFSET FINISHER TRAY CENTER TRAY STAPLE SORT SADDLE STITCH PUNCH GROUP [GROUP] key (See page 3-4.) [OK] key When Group is selected, all copies of the same original will be grouped.
00-08.book 7 ページ 2002年11月8日 金曜日 午前9時39分 SADDLE STITCH FINISHER Staple cartridge replacement and staple jam removal When the staple cartridge becomes empty or staples become jammed, a message will appear in the message display of the operation panel. Follow the procedure below to replace the staple cartridge or remove jammed staples. ■ Staple cartridge replacement 1 Open the front cover. a new 5 Insert staple box.
00-08.book 8 ページ 2002年11月8日 金曜日 午前9時39分 SADDLE STITCH FINISHER ■ Staple jam removal the saddle stitch finisher and slide 1 Unlatch it away from the main unit. 2 Open the front cover. roller rotating knob C as shown in the 3 Turn illustration until the blue indication is seen. 6 Remove the misfed paper. Be careful not to tear the misfed paper during removal. 7 Close the saddle stitch section cover. 8 Pull out the stapler section. Roller rotating knob C Blue the 4 Remove compiler.
00-08.book 9 ページ 2002年11月8日 金曜日 午前9時39分 SADDLE STITCH FINISHER 11 Raise the lever at the end of the staple box. the 14 Push finisher. stapler section back into the Remove the top staple if it is bent. If bent staples remain, a staple jam will occur again. 12 Return the lever to its original position. 15 Close the front cover. 3 13 Reinstall the staple box. Push the staple box in until it clicks into place. the 16 Push finisher.
00-08.book 10 ページ 2002年11月8日 金曜日 午前9時39分 SADDLE STITCH FINISHER Misfeed in the saddle stitch finisher When a misfeed occurs in the saddle stitch finisher, remove the misfed paper following the procedure below. the saddle stitch finisher and slide 1 Unlatch it away from the main unit. 5 Close the top cover. the misfed paper from the main 2 Remove unit. saddle stitching was selected, open the 6 Iffront cover.
00-08.book 11 ページ 2002年11月8日 金曜日 午前9時39分 SADDLE STITCH FINISHER 10 Remove the misfed paper. 13 Close the saddle stitch section cover. Be careful not to tear the misfed paper during removal. roller rotating knob in the direction of 11 Turn the arrow. 14 Close the front cover. 3 any misfed paper from the saddle 12 Remove stitch tray. the saddle stitch 15 Push against the main unit. finisher back Be careful not to tear the misfed paper during removal.
00-08.book 12 ページ 2002年11月8日 金曜日 午前9時39分 SADDLE STITCH FINISHER Troubleshooting saddle stitch finisher problems Check the list below before calling for service. Problem Stapling position is not correct (including saddle stitch). The saddle stitch finisher does not operate. Stapling cannot be performed (including saddle stitch). The punch hole positions are not correct*1 Check Solution or cause Stapling position not set properly? Check the stapling position setting. (See pages 3-4, 3-13 and 3-14.
00-08.book 13 ページ 2002年11月8日 金曜日 午前9時39分 SADDLE STITCH FINISHER Stapling position quick reference guide for duplex output The orientation of the copy paper, original, scanned original data, and binding position selection are all interrelated. The table below shows these relationships. Orientation of original or original data Page 1 Page 2 Page 1 & Page 2 Duplexed Output result One-position stapling Two-position stapling Left binding Two-position stapling along the shorter edge is not possible.
00-08.book 14 ページ 2002年11月8日 金曜日 午前9時39分 SADDLE STITCH FINISHER Relation between print image and saddle stitch The orientation of the copy paper, original, scanned original data, and binding position selection are all interrelated. The table below shows these relationships.
00-08.book 15 ページ 2002年11月8日 金曜日 午前9時39分 LARGE CAPACITY TRAY The large capacity tray provides the added convenience of having 3,000 additional sheets of 8-1/2" x 11" (A4) paper available. Part name Paper tray control button 3 Specifications Paper size 8-1/2" x 11" (A4) Page weight 17 to 28 lbs. (64 to 105 g/m2) Paper capacity 3,000 sheets (20 lbs. (80 g/m2)) Weight Approximately 71.7 lbs. (32.
00-08.book 16 ページ 2002年11月8日 金曜日 午前9時39分 LARGE CAPACITY TRAY Loading paper The large capacity tray will automatically lower when the tray runs out of paper. the paper tray control button on the 1 Press large capacity tray. The button lamp will blink while the feed table is lowering and will go out when the tray is ready to be opened. the button lamp goes out, pull the 2 When paper tray out. Do not pull the paper tray out before the button lamp goes out. 3 Fan the copy paper.
00-08.book 17 ページ 2002年11月8日 金曜日 午前9時39分 LARGE CAPACITY TRAY Misfeed removal When a misfeed occurs in the large capacity tray, remove the misfed paper, following the procedure below. holding the tray release lever, 1 While carefully slide the large capacity tray away 5 Remove the misfed paper. from the main unit until it stops. Release lever any misfed paper from the main 2 Remove unit and the large capacity tray. Upper right side cover ● Be sure not to tear the misfed paper during removal.
00-08.
00-08.
00-08.
00-08.book 1 ページ 2002年11月8日 金曜日 午前9時39分 CHAPTER 4 BEFORE MAKING COPIES This chapter provides basic information necessary for using the copier functions of the machine. Please read this chapter before making copies. Page PART NAMES AND FUNCTIONS (The Reversing Automatic Document Feeder) ....4-2 ● Exterior...................................................................................................4-2 ● Operation Panel .................................................................................
00-08.book 2 ページ 2002年11月8日 金曜日 午前9時39分 PART NAMES AND FUNCTIONS (The Reversing Automatic Document Feeder) Exterior [ ]Original reminder (page 4-6) *RADF exit area cover (page 7-2) Indicates an original is still on the document glass. Open to remove misfed originals. Document feeding area cover (page 7-2) *RADF exit area Open to remove misfed originals in this area. Finished originals are output here. Original guides (page 4-6) Document cover Adjust to the size of the originals.
00-08.book 3 ページ 2002年11月8日 金曜日 午前9時39分 PART NAMES AND FUNCTIONS (The Reversing Automatic Document Feeder) Operation Panel Touch panel (Details are on the next page 4-4) [CA] key (clear all key) Messages and touch keys are displayed here. Selections are made by touching the displayed keys. Selections made with the keys are confirmed by a "beep"* that is sounded when a key is touched, and highlighting of the selection key. * If a key that cannot be selected is touched, doublebeep will sound.
00-08.book 4 ページ 2002年11月8日 金曜日 午前9時39分 PART NAMES AND FUNCTIONS (The Reversing Automatic Document Feeder) Touch Panel (main screen of copy mode) The main screen of copy mode shows messages and keys necessary for copying and settings that can be selected. Touch a key to make a selection. The main screen of the copy mode will be displayed when the [COPY] key is pressed.* * Except when the custom settings screen is displayed. READY TO COPY.
00-08.book 5 ページ 2002年11月8日 金曜日 午前9時39分 REVERSING AUTOMATIC DOCUMENT FEEDER Originals set in the optional reversing automatic document feeder will be automatically fed and copied sequentially. The optional reversing automatic document feeder will handle 5-1/2" x 8-1/2" to 11" x 17" originals. Two-sided originals can be copied automatically without having to manually turn them over. Acceptable originals A stack of up to 100 original sheets (8-1/2" x 11" (A4) size, 20lbs.
00-08.book 6 ページ 2002年11月8日 金曜日 午前9時39分 SETTING ORIGINALS ■ When using the reversing automatic document feeder the document cover, make sure that 1 Open an original has not been left on the document glass, and then gently close the document cover. If an original is left on the document glass, the original reminder indicator ( ) will blink. Remove the original from the document glass.
00-08.book 7 ページ 2002年11月8日 金曜日 午前9時39分 SETTING ORIGINALS ■ Standard original setting orientation [Example 1] Document feeder tray Document glass Top Place originals in the document feeder tray or on the document glass so that the top and bottom of the original is positioned as shown in the illustration. If not, staples will be incorrectly positioned and some special features may not give the expected result.
00-08.
00-08.book 1 ページ 2002年11月8日 金曜日 午前9時39分 CHAPTER 5 BASIC PROCEDURE FOR MAKING COPIES This chapter explains the procedures for using basic copy functions, including making normal copies and enlarging/reducing copies. Page NORMAL COPYING ......................................................................................5-2 ● Copying from the reversing automatic document feeder .......................5-2 ● Automatic two-sided copying from the reversing automatic document feeder...
00-08.book 2 ページ 2002年11月8日 金曜日 午前9時39分 NORMAL COPYING This section describes the normal copying procedure. Copying from the reversing automatic document feeder NOTE Certain restrictions exist depending on the amount of memory installed and the copy settings. (See "Copy mode output restrictions" and "Specifications for memory capacity and maximum number of originals" on page 5-4.). ■ 1-sided copies of 1-sided originals Original Copy the originals in the document feeder 1 Place tray.
00-08.book 3 ページ 2002年11月8日 金曜日 午前9時39分 NORMAL COPYING the desired output mode (see page 7 Select 5-5). 2-SIDED COPY OUTPUT The sort mode is the default mode. To select the group mode, touch the [OUTPUT] key, then touch the [GROUP] key on the output setting screen, and then touch the [OK] key on the setting screen. the numeric keys to set the desired 8 Use number of copies. Up to 999 can be set. If you are only making a single copy, the copy can be made with the copy number display showing "0".
00-08.
00-08.
00-08.book 6 ページ 2002年11月8日 金曜日 午前9時39分 NORMAL COPYING Automatic two-sided copying from the reversing automatic document feeder When a duplex module/2 x 500 sheet paper drawer and a duplex bypass/inverter unit are installed, the following automatic two-sided copy functions are possible. The copy paper is turned over automatically, allowing easy twosided copying. NOTE Certain restrictions exist depending on the amount of memory installed and the copy settings.
00-08.book 7 ページ 2002年11月8日 金曜日 午前9時39分 NORMAL COPYING Copying from the document glass When copying originals which cannot be fed from the reversing automatic document feeder such as thick originals, open the document cover and copy the originals from the document glass. NOTE Certain restrictions exist depending on the amount of memory installed and the copy settings. (See "Copy mode output restrictions" and "Specifications for memory capacity and maximum number of originals" on page 5-4.).
00-08.book 8 ページ 2002年11月8日 金曜日 午前9時39分 NORMAL COPYING the desired output mode. (See page 4 Select 5-5.) the [COLOR COPY START ( 6 Press or [BLACK COPY START ( )] key. When a document is detected on the 2-SIDED COPY document glass, the group mode will be automatically selected. OUTPUT To select sort copy, touch the [OUTPUT] key, then touch the [SORT] key on the displayed screen, and then touch the [OK] key.
00-08.book 9 ページ 2002年11月8日 金曜日 午前9時39分 NORMAL COPYING Automatic two-sided copying from the document glass When a duplex module/2 x 500 sheet paper drawer and a duplex bypass/inverter unit are installed, the following automatic two-sided copy function is possible. The copy paper is turned over automatically, allowing easy two-sided copying. NOTE Certain restrictions exist depending on the amount of memory installed and the copy settings.
00-08.book 10 ページ 2002年11月8日 金曜日 午前9時39分 EXPOSURE ADJUSTMENTS Exposure selections for this copier should be selected according to the type of originals being copied: TEXT/PRTD. PHOTO, TEXT/PHOTO, TEXT, PHOTO, PRINTED PHOTO or MAP. If the original image type is TEXT/PRTD. PHOTO, TEXT or TEXT/PHOTO, the exposure can be adjusted automatically or manually. If the original image type is PHOTO, PRINTED PHOTO or MAP, the exposure can be adjusted manually only.
00-08.book 11 ページ 2002年11月8日 金曜日 午前9時39分 EXPOSURE ADJUSTMENTS a setting other than "AUTO" has been 3 Ifselected in step 2, manually adjust the copy exposure. MANUAL 1 3 TE 5 PRIN PHOT Touch the key to make darker copies. Touch the key to make lighter copies. To return to the automatic exposure mode, touch the [EXPOSURE] key and select [AUTO]. NOTE The exposure level for automatic exposure adjustment can be changed using the key operator program on page 13 of the key operator's guide.
00-08.book 12 ページ 2002年11月8日 金曜日 午前9時39分 REDUCTION/ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected either automatically or manually as described in this section. Automatic selection (auto image) The reduction or enlargement ratio will be selected automatically based on the original size and the selected paper size. the original in the document feeder 1 Place tray (when a reversing automatic 0 ORIGINAL 8½x11 document feeder is installed) or on the document glass.
00-08.book 13 ページ 2002年11月8日 金曜日 午前9時39分 REDUCTION/ENLARGEMENT/ZOOM Manual selection Manual selections can be made in the range of 25% to 400%. There are four preset reduction ratios (25%, 50%, 64% and 77%) and four preset enlargement ratios (121%, 129%, 200% and 400%) available for the inch system. There are six preset reduction ratios (25%, 50%, 64%, 70%, 81% and 86%) and five preset enlargement ratios (115%, 122%, 141%, 200% and 400%) available for the AB system.
00-08.book 14 ページ 2002年11月8日 金曜日 午前9時39分 REDUCTION/ENLARGEMENT/ZOOM that the desired paper size has 6 Ensure been automatically selected based on the selected copy ratio or select another size as needed. 0 INTERRUPT ORIGINAL PLAIN 8½x11 11x17 AUTO EXPOSURE Auto paper select display AUTO 8½x14 PAPER SELECT 8½x11 DUPLEX 8½x11 8½x14 77% COPY RATIO NOTE If the auto paper select display does not appear, no appropriate paper size for the selected ratio is available.
00-08.book 15 ページ 2002年11月8日 金曜日 午前9時39分 REDUCTION/ENLARGEMENT/ZOOM XY ZOOM The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed independently. If this feature is selected, the copy ratios can be set from 25% or 45% to 400%.
00-08.book 16 ページ 2002年11月8日 金曜日 午前9時39分 REDUCTION/ENLARGEMENT/ZOOM the 7 Use ZOOM ([ reduction, enlargement, and ], [ ]) keys to change the copy ratio in the vertical (Y) direction. 77% A fixed ratio key will not become highlighted when touched. X A 64% all other desired settings such as 10 Make exposure, paper size and number of copies and then press the [COLOR COPY START ( )] or [BLACK COPY START ( )] key.
sec_whale_05-2.fm 17 ページ 2002年12月2日 月曜日 午後3時35分 SPECIAL PAPERS Special papers including transparency film, postcards and envelopes must be fed through the bypass tray. the original in the document feeder 1 Place tray (when a reversing automatic document feeder is installed) or on the document glass. (page 4-6) 2 Load the special paper in the bypass tray. See pages 2-6 and 2-9 for the specifications of paper that can be used in the bypass tray.
00-08.
00-08.book 1 ページ 2002年11月8日 金曜日 午前9時39分 CHAPTER 6 CONVENIENT COPY FUNCTIONS This chapter explains special-purpose functions, storing of copy settings, and other convenient functions. Please select and read sections of this chapter as needed. Page SPECIAL MODES..........................................................................................6-2 ● Common operation procedure for using the special functions ...............6-3 ● Margin shift ..........................................................
00-08.book 2 ページ 2002年11月8日 金曜日 午前9時39分 SPECIAL MODES When the [SPECIAL MODES] key on the main screen of the copy mode is touched, the special modes screen containing eight special function touch keys will appear. These functions are shown below. Touch the [SPECIAL MODES] key in the main screen READY TO COPY.
00-08.book 3 ページ 2002年11月8日 金曜日 午前9時39分 SPECIAL MODES Common operation procedure for using the special functions 1 Touch the [SPECIAL MODES] key. SPECIAL MODES 2-SIDED COPY 2 Touch mode. the key for the desired special MARGIN SHIFT Example: To set the margin shift function TRANSPARENCY INSERTS If you touch the menu keys for color adjustment or image editing, you will go to the menu screen for selection of the corresponding functions.
00-08.book 4 ページ 2002年11月8日 金曜日 午前9時39分 SPECIAL MODES Margin shift The margin shift function will automatically shift the text or image on the copy paper approximately 1/2" (10 mm) in its initial setting. One-sided copying Image shifted to the right Original Margin Image shifted to the left ● The shift direction can be selected from right or left shift as shown in the illustration.
00-08.book 5 ページ 2002年11月8日 金曜日 午前9時39分 SPECIAL MODES Erase The erase function is used to erase the shadow lines on copies produced when copying thick originals or books. The erase modes that can be selected are shown below. The erase width is approximately 1/2" (10 mm) in it’s initial setting. Original Copy EDGE ERASE Eliminates shadow lines around the edges of copies caused when heavy paper or a book is used as an original.
00-08.book 6 ページ 2002年11月8日 金曜日 午前9時39分 SPECIAL MODES Dual page copy The dual page copy function produces separate copies of two documents placed side by side on the document glass. It is especially useful when copying books and other bound documents. [Example] Copying right and left pages of a book Book original Dual page copy ● The dual page copy function can be used with reduction copying but cannot be used with enlargement copying.
00-08.book 7 ページ 2002年11月8日 金曜日 午前9時39分 SPECIAL MODES Centering When the original and copy paper are of different sizes, CENTERING is used to shift the image to the center of the copy paper but only in the left to right direction. [Example] Original the [CENTERING] 1 Touch SPECIAL MODES screen. OK PAGE Y ENTS CENTERING IMAGE EDIT the [OK] 2 Touch MODES screen.
sec_whale_06-1.fm 8 ページ 2002年11月13日 水曜日 午後9時50分 SPECIAL MODES Transparency film with insert sheets 2 4 When copying onto transparency film, blank insert sheets can be placed between transparent sheets. Example: Inserting insert sheets between transparencies ●Insert sheets cannot be copied on in any mode. Originals (1-sided) ●This mode can be selected only in the 1-sided to 14 sided and 2-sided to 1-sided modes. 3 2 ●A multiple number of copies cannot be selected in 1 4 this mode.
00-08.book 9 ページ 2002年11月8日 金曜日 午前9時39分 SPECIAL MODES Covers The COVERS mode is used to place covers on the front, back, or both the front and back of multipage documents. To use the COVERS mode, an optional reversing automatic document feeder must be installed.
00-08.book 10 ページ 2002年11月8日 金曜日 午前9時39分 SPECIAL MODES the [COVERS] key on the SPECIAL 1 Touch MODES screen. FT D P ERASE ENCY 2 C ADJU COVERS The COVERS setting screen will appear. The covers icon ( , etc.) will also appear in the upper left of the screen to indicate that the function is turned on. Select cover placement. OK SPECIAL MODES CANCEL COVERS FRONT BACK FRONT+BACK OK PRINT ON FRONT COVER? YES NO Select [FRONT], [BACK] or [FRONT+BACK] on the touch panel.
00-08.book 11 ページ 2002年11月8日 金曜日 午前9時39分 COLOR ADJUSTMENTS MENU The [COLOR ADJUSTMENTS] menu in [SPECIAL MODES] enables the following parameters to be adjusted to modify the characteristics of a color copy. Settings adjusted with the color adjustments menu do not affect black and white copying. OK SPECIAL MODES MARGIN SHIFT TRANSPARENCY INSERTS ERASE COVERS DUAL PAGE COPY CENTERING COLOR ADJUSTMENTS IMAGE EDIT Touch the [COLOR ADJUSTMENTS] key in the SPECIAL MODES screen.
sec_whale_06-1.fm 12 ページ 2002年11月13日 水曜日 午後9時50分 COLOR ADJUSTMENTS MENU RGB adjust Strengthens or weakens one of three primary colors, red (R), green (G), or blue (B). the [RGB ADJUST] key on the 1 Touch COLOR ADJUSTMENTS menu screen. OLOR ADJUSTMENTS RGB ADJUST SH COLOR BALANCE BR The COLOR ADJUSTMENTS setting screen will appear. a color from R (RED), G (GREEN), 2 Select and B (BLUE). OK COLOR ADJUSTMENTS CANCEL RGB ADJUST OK ONLY ONE COLOR CAN BE ADJUSTED.
00-08.book 13 ページ 2002年11月8日 金曜日 午前9時39分 COLOR ADJUSTMENTS MENU Sharpness Sharpens or softens image outlines. the [SHARPNESS] key on the 1 Touch COLOR ADJUSTMENTS menu screen. T SHARPNESS SUPP BACK NCE BRIGHTNESS IN The SHARPNESS setting screen will appear. The color adjustments icon ( ) will also appear in the upper left of the screen to indicate that the function is turned on. the [SOFT] key to soften image 2 Touch outlines or touch the [SHARP] key to sharpen them.
00-08.book 14 ページ 2002年11月8日 金曜日 午前9時39分 COLOR ADJUSTMENTS MENU Color balance This function is used to adjust the color, tone, and density of color copies. the [COLOR BALANCE] key on the 1 Touch COLOR ADJUSTMENTS menu screen. RGB ADJUST SH COLOR BALANCE BRI The COLOR BALANCE setting screen will appear. the keys indicated in the illustration 2 Use below to adjust the color balance settings.
sec_whale_06-1.fm 15 ページ 2002年11月13日 水曜日 午後9時51分 COLOR ADJUSTMENTS MENU Brightness This copier allows the level of brightness of images to be adjusted. the [BRIGHTNESS] key on the 1 Touch COLOR ADJUSTMENTS menu screen. the [OK] key (inside [OK] key) on 3 Touch the BRIGHTNESS setting screen. The BRIGHTNESS setting screen will appear. Return to the COLOR ADJUSTMENTS menu screen. T SHARPNESS SUPP BACK NCE BRIGHTNESS IN the [OK] key on the 4 Touch ADJUSTMENTS menu screen.
00-08.book 16 ページ 2002年11月8日 金曜日 午前9時39分 IMAGE EDIT MENU To use the following convenient copy functions, touch the [IMAGE EDIT] key in [SPECIAL MODES]. OK SPECIAL MODES MARGIN SHIFT TRANSPARENCY INSERTS ERASE COVERS DUAL PAGE COPY COLOR ADJUSTMENTS Touch the [IMAGE EDIT] key on the SPECIAL MODES screen.
00-08.book 17 ページ 2002年11月8日 金曜日 午前9時39分 IMAGE EDIT MENU Single color Produces copies with a selected single color. the [SINGLE COLOR] key on the 1 Touch IMAGE EDIT screen. IMAGE EDIT M I SINGLE COLOR FULL-BLEED The SINGLE COLOR setting screen will appear. MULT ENLA Return to the IMAGE EDIT menu screen. the [OK] key on the IMAGE EDIT 4 Touch menu screen. Return to the SPECIAL MODES screen. the [OK] 5 Touch MODES screen. 2 Select the desired color.
00-08.book 18 ページ 2002年11月8日 金曜日 午前9時39分 IMAGE EDIT MENU Photo Repeat PHOTO REPEAT is used to produce repeated images of a photo on a single sheet of copy paper. ● Up to 24 repeats can be made on a single copy sheet. The number of copies on a single sheet depends on the original size and copy paper size. ● Reduction or enlargement cannot be selected with this function. If reduction or enlargement has been selected, the copy ratio will be reset to 100% when this function is selected.
00-08.book 19 ページ 2002年11月8日 金曜日 午前9時39分 IMAGE EDIT MENU the [PHOTO REPEAT] key on the 1 Touch IMAGE EDIT menu screen. R GE NT PHOTO REPEAT MU EXTRA SIZE PAMP The PHOTO REPEAT setting screen will appear. Return to the SPECIAL MODES screen. the [OK] 5 Touch MODES screen. key on the SPECIAL Return to the main screen of copy mode. the key for the desired combination 2 Touch of original type and paper size.
00-08.book 20 ページ 2002年11月8日 金曜日 午前9時39分 IMAGE EDIT MENU the [MULTI SHOT] 1 Touch IMAGE EDIT menu screen. OK AT MULTI SHOT E PAMPHLET COPY key on the The MULTI SHOT setting screen will appear. The multi shot icon ( , etc.) will also appear in the upper left of the screen to indicate that the function is turned on. the number of originals to be 2 Select copied onto one sheet of copy paper on the multi shot selection screen.
00-08.book 21 ページ 2002年11月8日 金曜日 午前9時39分 IMAGE EDIT MENU 11" x 17" (A3) Full-bleed In other copy modes, image loss will occur along the copy edges. When the 11" x 17" (A3) FULL-BLEED function is used, the full image of an 11" x 17" (A3) size original will be copied onto 12" x 18" (A3W) size copy paper. Reduction or enlargement cannot be selected with this function. If reduction or enlargement has been selected, the copy ratio will be reset to 100% when this function is selected.
sec_whale_06-2.fm 22 ページ 2002年11月13日 水曜日 午後9時51分 IMAGE EDIT MENU Multi-page enlargement This function is used to enlarge an original image to a size larger than 11" x 17" (A3) and print divided images onto multiple sheets of copy paper. [Example] Copy (enlarged image on 8 sheets of 11" x 17" (A3) paper) Original (8-1/2" x 11" (A4) size) Overlap of sections of image ● There will be a margin around the edges of each copy. ● The original image will be divided and copied onto multiple sheets of paper.
sec_whale_06-2.fm 23 ページ 2002年11月13日 水曜日 午後10時8分 IMAGE EDIT MENU the placement orientation and the 4 Check number of copies Example: Enlargement size = 22" x 17" (A2), original size = 8-1/2" x 11" (A4) OK IMAGE EDIT CANCEL MULTI-PAGE ENLARGEMENT ENLARGEMENT SIZE (INCH) 22x34 22x17 34x44 44x68 key on the SPECIAL Return to the main screen of copy mode. About the steps that follow See pages 5-7 and 5-8. OK ORIGINAL SIZE & ORIENTATION 11x17 8½x14 the [OK] 8 Touch MODES screen.
00-08.book 24 ページ 2002年11月8日 金曜日 午前9時39分 IMAGE EDIT MENU Extra size The EXTRA SIZE function provides a method for entering the dimensions of non-standard size copy paper and nonstandard size originals for the purpose of automatic enlargement or reduction of the image (page 5-12) for a best fit onto the copy paper. the original in the document feeder 1 Place tray (when a reversing automatic the [OK] 6 Touch MODES screen. document feeder is installed) or on the document glass.
00-08.book 25 ページ 2002年11月8日 金曜日 午前9時39分 IMAGE EDIT MENU Pamphlet copy The pamphlet copy function is used to arrange copies in proper order for eventual center-stapling and folding into a booklet. Two original pages are copied onto each side of copy paper. Four pages are, therefore, copied onto one sheet. This function is convenient for arranging copies into an attractive booklet or pamphlet. The pamphlet copy function can only be used for black and white copying.
00-08.book 26 ページ 2002年11月8日 金曜日 午前9時39分 JOB PROGRAM MEMORY Frequently used job programs can be stored in each of ten storage registers. This is convenient for quick job recall without losing time manually reprogramming each aspect of a job. Job programs can be recalled with ease, and the programs are retained even when the power is turned off. By programming frequently used copy settings, you can eliminate the bother of selecting the settings each time you use them for a copy job.
00-08.book 27 ページ 2002年11月8日 金曜日 午前9時39分 JOB PROGRAM MEMORY Recalling a job program 1 Press the [#/P] key. the number of copies as needed and 3 Set press the [COLOR COPY START ( )] or [BLACK COPY START ( )] key. Copying will start with the settings of the recalled job program. the desired storage register 2 Touch number key to recall the job from memory. When a number key is touched, the selection screen will be closed and the stored job program will be recalled.
00-08.book 28 ページ 2002年11月8日 金曜日 午前9時39分 INTERRUPTING A COPY RUN INTERRUPT can be used to temporarily stop a long copy run so that another copy job can be run. It is not possible to interrupt an automatic two-sided copy job. 1 Touch the [INTERRUPT] key. 0 INTERRUPT ORIGINAL 8½x11 PLAIN 5½x8½ AUTO EXPOSURE all other desired settings such as 3 Make exposure, paper size and number of If the [INTERRUPT] key does not appear, interrupt copying is not possible.
00-08.book 1 ページ 2002年11月8日 金曜日 午前9時39分 CHAPTER 7 MACHINE MAINTENANCE (FOR COPYING) This chapter explains procedures for removing misfeeds in a reversing automatic document feeder, cleaning the machine, and troubleshooting. Page REMOVING AN ORIGINAL MISFEED ..........................................................7-2 ● Removing a misfed original from the reversing automatic document feeder .....7-2 USER MAINTENANCE..................................................................................
00-08.book 2 ページ 2002年11月8日 金曜日 午前9時39分 REMOVING AN ORIGINAL MISFEED Removing a misfed original from the reversing automatic document feeder If an original misfeed occurs in the reversing automatic document feeder, follow the steps below to remove the misfed original. NOTES ● For misfeed removal in the main unit and other peripheral devices, see page 2-18. ● When a misfeed occurs, touch the [INFORMATION] key to display detailed information for misfeed removal.
00-08.book 3 ページ 2002年11月8日 金曜日 午前9時39分 USER MAINTENANCE The document glass, document cover and the transport belt of the optional reversing automatic document feeder must be kept clean to avoid dirty areas from being copied onto the copies. Wipe the document glass, document cover and the transport belt of the optional reversing automatic document feeder with a soft, clean cloth. NOTE If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents.
00-08.book 4 ページ 2002年11月8日 金曜日 午前9時39分 TROUBLESHOOTING Whenever the machine stops or operation is not possible, check the operation panel display for messages. In most cases, these messages will give sufficient information to return the machine to an operating condition. In cases where this information is not enough, check the list below for more information. This section describes problems concerning copier features.
00-08.book 5 ページ 2002年11月8日 金曜日 午前9時39分 TROUBLESHOOTING Problem Order of copies incorrect Check Is the order of originals correct? Color copies are being made on special paper such as heavy paper 2, transparency film, or envelopes (paper that can only be output face up). Job cancelation needed Scanning of originals is incomplete.
00-08.
00-08.book 1 ページ 2002年11月8日 金曜日 午前9時39分 CHAPTER 8 SPECIFICATIONS This chapter provides specifications for the items indicated below. For the specifications of the peripheral devices, see Chapter 3. For the specifications of the stand with paper drawers, see the section that explains how to load paper in the stand with paper drawers. For the specifications of the printer controller and network scanner, see the printer controller and network scanner manuals. Page SPECIFICATIONS ..........................
00-08.book 2 ページ 2002年11月8日 金曜日 午前9時39分 SPECIFICATIONS Copier and Main unit Type Desktop (can be upgraded to console type if an optional stand is installed.
00-08.book 3 ページ 2002年11月8日 金曜日 午前9時39分 SPECIFICATIONS Continuous copying speed (when the offset function is not used) Black and white copying Copy paper size 100% / Reduced / Enlarged 11" x 17" (A3) 15 copies/min. 12" x 18" (A3 wide) 7 copies/min. 8-1/2" x 14" (B4) 17 copies/min. 8-1/2" x 11" : 32 copies/min. 8-1/2" x 11" (A4) A4 : 33 copies/min. 8-1/2" x 11"R (A4R) 22 copies/min. 7-1/4" x 10-1/2"R (B5R) 22 copies/min. 8-1/2" x 5-1/2" (A5) 33 copies/min.
00-08.book 4 ページ 2002年11月8日 金曜日 午前9時39分 SPECIFICATIONS Reversing automatic document feeder (optional) Original feed system Automatic continuous feeding Original transport system RADF: sheet through type (reference position: center), document glass: reference position is left rear Original setting direction Face up Original sizes 5-1/2" x 8-1/2" to 11" x 17" (A5 to A3) Original weight One-sided original : 14 to 54 lbs. (50 to 200 g/m2) Two-sided original : 14 to 42 lbs.
00-08.book 5 ページ 2002年11月8日 金曜日 午前9時39分 INDEX [#/P] key ................................................................. 4-3 [ ] key ................................................................... 4-3 1-sided copies ................................................. 5-2, 5-7 ■ A ACC.#-C................................................... 1-11 to 1-12 Acceptable originals ............................................... 4-5 Account number ...................................................
00-08.book 6 ページ 2002年11月8日 金曜日 午前9時39分 INDEX ■ I Icon ........................................................................ 1-9 If the machine is to be left unused for a long time.. 0-3 Image edit menu ........................................... 6-2, 6-16 Image send ............................................................ 1-8 Information ........................................................... 2-18 Insert sheets...........................................................
00-08.book 7 ページ 2002年11月8日 金曜日 午前9時39分 INDEX ■ R RADF exit area....................................................... 4-2 RADF exit area cover...................................... 4-2, 7-2 Read-end ............................................................... 5-8 Recalling a job program ....................................... 6-27 Reduction/enlargement ........................................ 5-12 Registration adjustment ....................................... 2-24 Replacing the toner cartridges .
00-08.
00-08.
00-08.
00-08.book 1 ページ 2002年11月8日 金曜日 午前9時39分 NOTICE BE SURE TO ASK YOUR AUTHORIZED SHARP DEALER ABOUT THE WARRANTY THAT YOUR SELLING DEALER EXTENDS TO YOU. In order to assure you, the end-user, of warranty protection, Sharp extends a limited warranty to each of its authorized dealers and, in turn, requires each of its authorized dealers to extend its own warranty to you on terms that are no less favorable than those given to the dealer by Sharp.
AR-C260/AR-C260M (for general information and copier operation) SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135.