ENGLISH DEUTSCH PN-465E FRANÇAIS LCD MONITOR LCD FARBMONITOR MONITEUR LCD МОНИТОР ЖКД 液晶显示器 РУССКИЙ ENGLISH ...... E1 DEUTSCH ..... D1 FRANÇAIS .... F1 РУССКИЙ ..... Р1 汉语 ...............
Authorised representative responsible for the European Union Community Market Autorisierter Repräsentant in der Europäischen Union Représentant autorisé pour le marché de la communauté européenne SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg
LCD MONITOR ENGLISH PN-465E ENGLISH IMPORTANT INFORMATION FOR CUSTOMERS IN U.K.
IMPORTANT INFORMATION (Continued) CAUTION: Use the supplied power cord as it is. This product utilises fluorescent tubes containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eia.org Attention: Your product is marked with this symbol.
DEAR SHARP CUSTOMER SAFETY PRECAUTIONS ENGLISH Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product. Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety.
SAFETY PRECAUTIONS (Continued) 15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorised parts can result in fire, electric shock and/or other danger. 16.
TIPS AND SAFETY INSTRUCTIONS - Do not display a still picture for a long period, as this could cause a residual image. - Never rub or tap the monitor with hard objects. - Please understand that Sharp Corporation bears no responsibility for errors made during use by the customer or a third party, nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognised under law. - This monitor and its accessories may be upgraded without advance notice.
Contents Introduction IMPORTANT INFORMATION............................................1 DEAR SHARP CUSTOMER..............................................3 SAFETY PRECAUTIONS..................................................3 TIPS AND SAFETY INSTRUCTIONS ...............................5 Supplied Accessories......................................................7 Part Names .......................................................................7 Front view.....................................................
Supplied Accessories If any component should be missing, please contact your dealer. � Power cord (Approx. 4 m): 1 � R-6 battery: 2 � CD-ROM (Utility Disk for Windows): 1 � Operation manual: 1 � Blank sticker: 1 Place a blank sticker onto the SHARP logo to cover the logo. � Remote control unit: 1 � Vertical logo sticker: 2 � Temporary stand: 2 � Cable clamp: 2 ENGLISH � Liquid Crystal Display: 1 � Power cord clamp: 1 INPUT * Sharp Corporation holds authorship rights to the Utility Disk programme.
Part Names Rear view 1. 2. 3. 4. 16 15 1 2 6 3 4 5 8 9 7 11 10 14 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Main power switch (See page 14.) AC input terminal (See page 12.) PC/AV output terminal (DVI-D) (See page 11.) PC1 input terminal (DVI-D) (See page 10.) AV1 input terminal (DVI-D) (See page 10.) PC2 input terminal (Mini D-sub 15 pin) (See page 10.) PC3 input terminals (BNC) (See page 10.) AV2 input terminals (BNC) (See page 10.) AV3 input terminal (BNC) (See page 10.
How to Install the Monitor • Since the monitor is heavy, consult your dealer before installation. • Installing or moving the monitor must be done by two or more people. • A stand and mounting bracket compliant with VESA specifications is required. Do not use any screw holes other than VESA holes for installation. • When moving the monitor, be sure to hold it with the handles both on the rear and the unit bottom. Do not hold the LCD panel. This may cause product damage, failure, or injury.
Connecting Peripheral Equipment Caution • Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/ disconnecting cables. Also, read the manual of the equipment to be connected. • Be careful not to mix up the input terminal with the output terminal when connecting cables. Mixing up the input and output terminals may cause malfunctions and the other problems.
Connecting Peripheral Equipment Connecting multiple monitors PC/AV audio output terminals • Audio from the equipment connected to the AV audio input terminals or PC audio input terminal is output. Connect to the audio input terminals of the connected equipment using a commercially available audio cable (RCA). • The audio output varies depending on the input mode selection. (See page 15.) • The volume level can be adjusted using the volume adjustment. (See page 15.
Connecting the Power Cord Caution • Do not use a power cord other than the one supplied with the monitor. 1. Turn off the main power switch. 2. Plug the power cord (supplied) into the AC input terminal. 3. Plug the power cord (supplied) into the AC power outlet. 3 Main power switch 1 For power outlet 2 AC input terminal Power cord (Supplied) Mounting the Temporary Stands Caution • The monitor is heavy. It must be handled by 2 or more people.
Binding Cables ENGLISH Attaching the cable clamp Cable clamp positions The cables connected to the terminals on the back of the monitor can be neatly bundled using the supplied cable clamps as shown in the illustration. Insert the cable clamp into a hole. (any hole available) Cable clamp attachment Cable clamp Caution • Verify the position for attaching a cable clamp in advance. A cable clamp cannot be removed once it is attached.
Turning Power On/Off Caution TIPS • Turn on the monitor first before turning on the PC or playback device. Turning on the main power • If the monitor is in the input signal standby mode and you press the POWER button on the remote control unit, the monitor enters standby mode. • You can turn on/off the monitor by pressing the power switch of the monitor. • Setting the SCHEDULE flashes the power LED alternately in red and orange in standby mode.
Basic Operation 1 BRIGHT 2 3 ENGLISH 5. BRIGHT +/- (Backlight adjustment) Pressing or displays the BRIGHT menu when the menu screen is not displayed. 15 Press or to adjust the brightness. * If you do not press any buttons for about 4 seconds, the BRIGHT menu automatically disappears. 4 5 6. SIZE (Screen size selection) The menu is displayed. Press or to select the screen size. (See page 16.) 7. DISPLAY Displays monitor information.
Basic Operation Switching the screen size Even when the screen size is changed, the display may remain the same depending on the input signal. WIDE ZOOM 1 PC input Displays image so it fills the entire screen. AV input An image with a 4:3 aspect ratio is stretched to fill the entire screen. PC input An image with a 4:3 aspect ratio is enlarged to fill the entire screen without changing the aspect ratio. The edges of the image may be cut off.
Menu Items Menu screen display 1 Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 18 to 20 for details of each menu items. SCREEN PICTURE Example of operation (Adjusting CONTRAST in the PICTURE menu) MENU to display the menu screen. 1. Press SCREEN SCREEN 1/1 SETUP PHASE H-POS OPTION V-POS ENLARGE RESET PC2 ANALOG V: 60 Hz END…[MENU] 2. Press or to select PICTURE, and press PICTURE menu is displayed.
Menu Items Menu item details The menu will differ depending on the input mode. SCREEN (PC2/PC3) AUTO The CLOCK, PHASE, H-POS, and V-POS are automatically adjusted. Pressing performs adjustment. Use this automatic adjustment when you use the PC2 input terminal or PC3 input terminals to display a PC screen for the first time or when you change the setting of the PC. (See page 23.) Changes the colour mode on the screen. The colour mode on the screen can also be changed using a remote control unit.
Menu Items POWER ON DELAY Residual images are reduced by moving the screen. PATTERN 1 .... The whole screen moves vertically and horizontally. PATTERN 2 .... A black screen spreads from the bottom of the screen and then shrinks to the bottom of the screen. If the monitor is installed in the vertical orientation, a black screen spreads from the left end of the screen and then shrinks to the left end of the screen. PATTERN 3 .... A black bar moves from the left end to the right end of the screen.
Menu Items ENLARGE (PC input) ENLARGE MODE Sets the number of screen splits used for the enlargement. (See page 21.) ENLARGE POS Specify the split screen to be displayed when the enlargement function is used. (See page 21.) BEZEL H / BEZEL V Sets the frame width of the display when the enlargement function is used. H-POS Adjust the horizontal position of the enlarged screen. TIPS • When WHITE BALANCE is set to THRU, BLACK LEVEL, CONTRAST and GAMMA cannot be set.
Menu Items ENGLISH Enlarge You can align 4, 9, 16, or 25 monitors and integrate them into a single large screen to display. Enlarged views of separated images are displayed in each monitor.
Menu Items SCHEDULE Caution You can set the time to switch the monitor on and off. Set this function with “SCHEDULE” in the OPTION menu. (See page 19.) PC2 ANALOG SCHEDULE XXXX/XX/XX XXX XX:XX:XX No. (1) POWER (2) DAY OF THE WEEK (3) TIME (4) INPUT (5) • Do not switch off the main power after setting the SCHEDULE. • Specify the correct date and time. (See pages 14 and 19.) SCHEDULE does not function unless the date and time are specified. • Check regularly that the set date and time are correct.
Menu Items Automatic adjustment When you use the PC2 input terminal or PC3 input terminals to display a PC screen for the first time, or when you change the setting of the PC, use the automatic screen adjustment. 1. Switch the input to PC2 or to PC3 and display the adjustment pattern. (See the description below.) MENU 2. Press and use or to display the SCREEN menu. 3. Press ENGLISH Adjustments for PC screen display and select “AUTO”. . 4. Press The automatic adjustment is complete in several seconds.
Initialisation (Reset)/Functional Restriction Setting You can return the settings to their factory-preset values and restrict operations. 1. After pressing , SIZE , and for about 5 seconds, press , in that order. FUNCTION 1/1 ALL RESET ADJUSTMENT LOCK OFF OSD DISPLAY ON LED ON RS-232C UNLOCKED END…[MENU] 2. Select and set the items. ALL RESET Resets the settings to the factory default settings. MENU Press , select “ON” and then press .
Controlling the Monitor with a PC PC connection One-to-one connection with a PC Connect with RS-232C straight cable between the PC’s COM port (RS-232C connector) and the RS-232C input terminal on the monitor.
Controlling the Monitor with a PC Response code format When a command has been executed correctly O K Return code (0DH, 0AH) A response is returned after a command is executed. * If an ID number has been assigned Return code (0DH, 0AH) Space (20H) O K SPC 0 0 1 Communication interval • After OK or ERR is returned, you must send the following commands. To set a timeout for the command response, specify 10 seconds or longer.
Controlling the Monitor with a PC The command examples shown on this page assume the following connection and ID number set up. ID number: 1 ID number: 2 ID number: 3 ID number: 4 IDLK ........The parameter of this command sets the ID number of the monitor. The monitor is subject to all subsequent commands. Example: IDLK0002 WAIT IDST .........A monitor receiving this command sets its own ID number in the parameter field. Example: IDST0001 OK 001 ← The ID number of this monitor is set to 1.
Controlling the Monitor with a PC Repeater control This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. You can use Repeater control function without assigning ID numbers. [Example] Set 1 Set 2 Set 3 Set 4 * If monitors are connected as shown above, you can execute a command like “Set all monitors’ input settings to PC1 DIGITAL”.
Controlling the Monitor with a PC How to read the command table Command: Command field (See page 25.) Direction: W When the “Parameter” is set in the parameter field (see page 25), the command functions as described under “Control/Response Contents”. R The returned value indicated under “Reply” can be obtained by setting “????”, “ ?” or “???+” (repeater control) in the parameter field (see page 25). Parameter: Parameter field (See page 25.
Controlling the Monitor with a PC PICTURE menu Command Direction AUTO Function AGIN W CONTRAST CONT WR 0-60 0-60 0-127 on PC2/PC3. BLACK LEVEL BLVL WR 0-60 0-60 0-127 on PC2/PC3. TINT TINT WR 0-60 0-60 When the input mode is AV. COLOR COLR WR 0-60 0-60 0-24 SHARPNESS ADVANCED Reply Control/Response contents 1 When the input mode is PC2, PC3.
Controlling the Monitor with a PC Command Direction DATE/TIME SETTING Function DATE WR AABBCCDDEE Parameter AABBCCDDEE Reply AA: Year, BB: Month, CC: Day, DD: Time, EE: Minute Control/Response contents Yes * SCHEDULE SC01SC08 WR ABCDEFFGGH ABCDEFFGGH Schedule of a specified number A: Schedule 0 = Not effective, 1 = Effective B: Power 0 = OFF, 1 = ON C: Day of the week 1 0 = Only once, 1 = Every week, 2 = Every day D: Day of the week 2 0 = Sunday, 1 = Monday through 6 = Saturday, 9 = Not e
Controlling the Monitor with a PC Initialisation/Functional Restriction Setting (FUNCTION) menu Command Direction ALL RESET Functio RSET W Parameter Reply Control/Response contents ADJUSTMENT LOCK ALCK WR 0-2 0-2 0: OFF Yes OSD DISPLAY LOSD WR 0-1 0-1 0: ON, 1: OFF Yes LED OFLD WR 0-1 0-1 0: ON, 1: OFF Yes 0 * No Others Function Command Direction SCREEN SIZE (PC) WIDE WR SCREEN SIZE (AV) WIDE WR 1-5 VOLUME VOLM WR 0-31 0-1 MUTE Parameter Reply 1-5 Control/Respon
Troubleshooting There is no picture or sound. • Is the power cord disconnected? (See page 12.) • Is the main power switch set to “OFF”? (See page 14.) • Is the monitor in standby mode (the power LED illuminating in orange)? (See page 14.) • Make sure correct input mode is selected. (See page 15.) • If any external equipment is connected, make sure the equipment is operating (playing back). Remote control does not work. • Are the batteries inserted with polarity (+,-) aligned? (See page 13.
Specifications Product Specifications Model LCD element Max. resolution (pixels) Max. colours Pixel pitch Viewing angle Screen active area (mm) Computer input signal Sync signal PN-465E 46" wide (116.8 cm diagonal) ASV low-reflection black TFT LCD 1920 x 1080 16.77 M colours (8 bits/colour) 0.53025 mm (H) x 0.53025 mm (V) 176° right/left/up/down (contrast ratio ≥ 10) 1018.1 x 572.7 Digital (DVI 1.0 standard-compliant), Analogue RGB (0.
Specifications ENGLISH Dimensional Drawings Note that the values shown are approximate values. Unit: mm 87 VESA holes 52 200 1113 24 200 Opening height (576) Opening width (1023) 657 581 200 228.5 140 882 When mounting the monitor, be sure to use a wall-mount / ceiling-mount bracket they comply with the VESA-compatible mounting method. SHARP recommends using M6 screws and tighten the screws. Note that screw hole depth of the monitor is 10 mm.
Specifications Power management This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in order for the monitor’s power management function to work.
