Package Contents Package Contents Package Contents Handset (AQUOS ea) ・Battery is built into handset. ・Handset back cover is not removable.
Parts & Functions Handset (Front) Handset (Back and Sides) Handset Keys Handset (Front) Name Receiver Proximity/Light Sensor Display Front Camera Description Hear the other party's voice here. Proximity Sensor prevents Touchscreen misoperation during calls. Light Sensor adjusts Display brightness according to ambient light. Touchscreen-type display; operate with your fingers on Display. Use to shoot photos or videos of yourself.
Handset (Back and Sides) Name EarphonesMicrophone Jack Mobile Light Use as a camera flash, flashlight, etc. FeliCa mark Hold up to reader/writer to use NFC/Osaifu-Keitai®. External Connection Jack Mic (Recorder Mic) Connect AC Adaptor or Micro USB Cable here. Use while recording videos or when talking through Speakerphone. Camera Shoot photos or Card Slot videos. Insert/remove SD Card and USIM Card. Speaker 3 Description Connect TV Antenna Cable or Earphones with Mic (optional accessory) here.
Handset Keys Name (Power Key) Volue Up Key Volume Down Key 4/15 『aquos-xx3-mini_01_Getting Started.docx』 4 Description Turn Display off/on. Long Press for power on/off or reboot. Increase volume. Decrease volume. Long Press in lock screen to activate/cancel Manner mode.
USIM Card USIM Card is an IC card containing phone number and other customer information. Handling USIM Card Inserting USIM Card Removing USIM Card Handling USIM Card See instructions included with USIM Card for handling. Avoid applying labels. May damage USIM Card. USIM is replaceable (at cost) in case of loss/damage. Wipe clean with a dry, soft cloth. Always keep the IC (gold) chip clean. ① IC (gold) chip USIM Card Cautions About USIM Card Observe the following when using USIM Card.
Inserting USIM Card Always power off beforehand. Set USIM Card in USIM Tray beforehand. Do not insert USIM Card without setting it in USIM Tray.
Pull out USIM Tray Do not pull USIM Tray forcefully or at an angle; damage may result. Gently pull it out horizontally by hooking a finger on it. Set USIM Card in USIM Tray Place gently, noting orientation of USIM Card (notch/IC (gold) chip facing up). Make sure USIM Card is in USIM Tray. Inserting USIM Tray with USIM Card on its edge may cause damage.
Insert gently all the way horizontally, noting orientation of USIM Tray. Do not insert USIM Tray upside down. Close Card Slot Cap Push Card Clot Cap as shown ( area (○) to hinge as shown ( and ) to close, then push it firmly all the way from circled ) so that there is no gap between handset and Card Slot Cap. Removing USIM Card Always power off beforehand.
Pull out USIM Tray Do not pull USIM Tray forcefully or at an angle; damage may result. Gently pull it out horizontally by hooking a finger on it.
Insert USIM Tray into USIM Card Slot (right opening) Do not insert USIM Tray at an angle; damage may result. Insert gently all the way horizontally, noting orientation of USIM Tray. Do not insert USIM Tray upside down. Close Card Slot Cap Push Card Clot Cap as shown ( and ) to close, then push it firmly all the way from circled ) so that there is no gap between handset and Card Slot Cap.
Charging Handset Battery is built into handset. Internal Battery About Charging Charging with AC Adaptor Charging by PC Internal Battery A lithium-ion battery is built into handset; it is not removable. Recycling This product requires a lithium-ion battery. Lithium-ion batteries are recyclable. To recycle a used lithium-ion battery, take it to any shop displaying the recycling symbol.
Bulges of Internal Battery Depending on use, bulges may appear near end of battery life; this does not affect safety. Internal Battery Replacement Internal Battery is a consumable item; may need to be replaced if operating time shortens noticeably. Internal Battery is not user replaceable; its replacement incurs fees and requires handset submission to a SoftBank Shop or other appropriate servicer. For details, contact a SoftBank Shop or SoftBank Customer Support, General Information.
About Charging Abroad SoftBank Corp. is not liable for problems resulting from charging handset abroad. Charging with AC Adaptor Purchase and use ZSDBA4 (Micro USB Quick ChargeTM 2.0 AC Adaptor)1 or ZSDBA6 (Micro USB 1.0 A AC Adaptor)2. For information on other peripheral devices, see SoftBank Website. The following explains how to charge handset using ZSDBA4 (Micro USB Quick Charge TM 2.0 AC Adaptor). 1 SB-AC12-HDQC (SoftBank SELECTION Qualcomm® Quick ChargeTM 2.
Insert Micro USB plug in correct orientation; otherwise, External Connection Jack may be damaged. Check contours and orientation of Micro USB plug, then insert it with tabs (○) facing down. Raise plug on AC Adaptor and plug into household AC outlet Charging/Notification Lamp illuminates once charging starts. Charging/Notification Lamp goes out when charge is full.
Insert Micro USB plug in correct orientation; otherwise, External Connection Jack may be damaged. Check contours and orientation of Micro USB plug, then insert it with tabs (○) facing down. Insert USB plug of Micro USB Cable into USB port on PC Charging/Notification Lamp illuminates once charging starts. Charging/Notification Lamp goes out when charge is full.
Specifications Handset TV Antenna Cable Materials Handset Handset specifications are as follows. Times in the table vary with location, status, settings, etc. Display employs precision technology; however, some pixels may remain on/off. Item Description Dimensions (W x H x D) Approx. ●● mm x ●●● mm x ●.● mm (without protruding parts) Weight Approx. ●●● g Maximum Output 3G: ●.●● W GSM (850 MHz, 900 MHz): ● W GSM (1800 MHz, 1900 MHz): ● W 4G: ●.
SoftBank 3G: ●● Mbps in downlink, ●.● Mbps in uplink 1 2 3 4 5 6 7 8 9 Average measured with handset fully charged, in strong signal conditions at rest. Average measured with handset fully charged, without calls or operations, in strong signal conditions at rest, and with data communication and Urgent News disabled. May vary with battery strength, ambient temperature, settings, etc.
Power Key PC resin/coating, hard coating, printing Volume Up/Down Key PC resin/coating, hard coating, printing Camera Panel Acrylic resin + PC resin/AF coating + AR coating Camera Ornament Aluminum/anodizing Earpiece Screen Polyester resin/water-repellent treatment External Connection Jack (metal part) Copper alloy + SUS/gold plating, tin plating External Connection Jack (resin part) PA resin Card Slot Cap PC resin/coating, hard coating Card Slot Cap Hinge Elastomer resin Card Slot Cap Gas
Warranty & After-Sales Service Warranty After-Sales Service Warranty Handset purchase includes warranty. Check shop name and purchase date. Read warranty and keep in a safe place. Warranty period is given in warranty. Cautions Damages SoftBank Corp. is not responsible for any damages for user or third party resulting from lost opportunities to make a call, etc. due to breakage, malfunction, or trouble of product.
After the warranty period, if handset can be repaired, repairs will be made at cost. Further inquiries For more information on after-sales service, contact a nearby SoftBank Shop or Customer Service.
Customer Service For SoftBank handset or service information, call General Information. For repairs, call Customer Assistance.
Safety Precautions Read Safety Precautions before using handset. Observe precautions to avoid injury to self or others, or damage to property. Safety Precautions Handset, USIM Card, TV Antenna Cable, AC Adaptor (Sold Separately), Micro USB Cable (Optional Accessory), SD Card (Sold Separately) (Common) Handset AC Adaptor (Sold Separately) USIM Card TV Antenna Cable Handset Use & Electronic Medical Devices Safety Precautions These labels show degree of risk from improper use.
Prohibited actions Disassembly prohibited Exposure to liquids prohibited Use with wet hands prohibited Compulsory actions Unplug from outlet Handset, USIM Card, TV Antenna Cable, AC Adaptor (Sold Separately), Micro USB Cable (Optional Accessory), SD Card (Sold Separately) (Common) Do not use, store, or leave in extreme heat or where heat collects, such as fire, heat sources, under a kotatsu (blanketed warming table) or blanket, direct sunlight, inside vehicles in the hot sun, etc.
Do not charge handset while it is wet with water or other liquids (drinking water, sweat, sea water, pet urine, etc.). May cause fire, burns, injury, electric shock, etc. For details on water and dust resistance, see "Water & Dust Resistance." Do not disassemble or modify. May cause fire, burns, injury, electric shock, etc. Do not wet with water or other liquids (drinking water, sweat, sea water, pet urine, etc.). May cause fire, burns, injury, electric shock, etc.
Do not cover/wrap with a blanket, etc. while using or charging. May cause fire, burns, etc. If charging continues even after specified Charging Time, stop charging. Failure to do so may cause fire, burns, injury, etc. due to overcharge or for other reasons. Before entering an area with a risk of flammable gas generation (e.g., a gas station) or where dust is generated, be sure to power off handset and stop charging. Failure to do so may cause explosion, fire, etc.
temperatures. May cause fire, burns, electric shock, etc. For details on water and dust resistance, see "Water & Dust Resistance." For use by a child, explain instructions and supervise use. Failure to do so may cause injury, etc. Do not leave within the reach of small children. May cause accidental swallowing, injury, electric shock, etc. Handset may become hot if used continuously for an extended period or while charging. Be careful of prolonged contact even by accident such as falling asleep.
doctor immediately. Eye contact with substances in Internal Battery may cause loss of sight or other physical harm. If substances in Display get in eyes or mouth, do not rub; rinse with clean water and consult a doctor immediately. Substances in Display may cause loss of sight or other physical harm. Do not shine Mobile Light close to eyes. Maintain a safe distance, especially from small children.
Power off handset or activate Airplane mode before boarding an airplane. Handset use on airplanes is restricted; follow the instructions given by the respective airlines. Handset use may adversely affect an airplane's electronic devices. If you engage in a prohibited activity while using handset on an airplane, you may be punished by law. Regarding handset use in a hospital, follow the instructions given by the respective medical institution. Power off handset where handset use is prohibited.
If Display or Camera lens breaks, be careful with shards of broken tempered glass and exposed handset parts. Touching the broken or exposed parts may cause burns, injury, electric shock, etc. If Internal Battery leaks or there is abnormal odor, discontinue use immediately and keep sources of flame away. Leaked fluid may catch fire, causing the battery to ignite, burst, etc. Do not let your pet bite handset. Internal Battery may ignite, burst, overheat, or leak, causing fire, burns, injury, etc.
May cause fire, burns, injury, etc. due to ignition; may adversely affect the environment. When handset is no longer needed, take it to a SoftBank shop, or follow the local regulations regarding handset collection. If substances in Internal Battery leak, do not let them come into contact with skin (face, hands, etc.) or clothes. May cause loss of sight, skin damage, etc. If internal substances get in eyes or mouth or if they come into contact with skin or clothes, rinse with clean water immediately.
AC Adaptor (Sold Separately) Do not use AC Adaptor if the cord is damaged. May cause fire, burns, electric shock, etc. Do not use AC Adaptor in high humidity (e.g., in bathrooms). May cause fire, burns, electric shock, etc. Do not touch AC Adaptor if thunder is audible. May cause electric shock, etc. Do not short-circuit charging terminals when AC Adaptor is plugged into the outlet. In addition, keep your hands and other body parts away from charging terminals.
When AC Adaptor is connected to handset, do not apply excessive force to the connection. May cause fire, burns, injury, electric shock, etc. Do not touch AC Adaptor cord, charging terminals, or power plug with wet hands. May cause fire, burns, electric shock, etc. Use at the specified power supply voltage. When charging handset overseas, use AC Adaptor designed for overseas use. Use at other power supply voltages may cause fire, burns, electric shock, etc.
May cause fire, burns, injury, electric shock, etc. due to short-circuiting of charging terminals. Unplug AC Adaptor from the outlet when not in use. Leaving it plugged in may cause fire, burns, injury, electric shock, etc. If water or other liquids (drinking water, sweat, sea water, pet urine, etc.) enter, unplug from the outlet immediately. Failure to do so may cause fire, burns, electric shock, etc. Before cleaning, unplug AC Adaptor from the outlet.
If there is abnormal odor/sound, smoke, overheating, discoloration, distortion, or other abnormalities, disconnect TV Antenna Cable. Failure to do so may cause fire, burns, injury, electric shock, etc. When disconnecting TV Antenna Cable from handset, grasp plug and pull, without forcefully pulling cord. Pulling the cord may damage the cord, causing fire, burns, electric shock, etc. Do not touch TV Antenna Cable if thunder is audible. May cause electric shock, etc.
Handset Use & Electronic Medical Devices If you are using an electronic medical device (implanted pacemaker, implanted defibrillator, etc.), carry or use handset at least 15 cm away from where the device is. Radio waves may adversely affect operation of electronic medical devices. Before using an electronic medical device other than an implanted pacemaker or implanted defibrillator outside a medical institution (for home treatment, etc.), check with its manufacturer on radio wave effects.
Important Product Information General Use Heat from Handset Use Camera TV In-Call/Transmission Cautions Urgent News (Application) Technical Regulations Conformity Certification Voluntary Control of Radio Interference General Use If your USIM Card or handset (with USIM Card inserted) is lost or stolen, suspend your service immediately. For details, contact SoftBank Customer Support, General Information.
Export control regulations in the United States provide that an export license granted by the US government is required to carry handset into Cuba, Iran, North Korea, Sudan or Syria. Heat from Handset Use Handset internal temperature may increase depending on usage or environment, causing handset to become warm. (Handset may stop charging or Display brightness may be adjusted for safety.) If handset continues to be used while warm, warning appears and handset powers off after approximately 3 minutes.
Urgent News (Application) Urgent News is enabled by default (handset receives alerts). Alert tones are muted in Manner mode. Alerts are not received during calls/transmissions or in poor signal conditions. (Alerts can be received during voice calls over VoLTE.) Depending on usage/situation, handset may receive alerts for other areas or no alerts. Standby Time may decrease when Urgent News is enabled. SoftBank Corp.
Handset & Hardware Care Handset & Hardware Care USIM/SD Card Insertion/Removal Display (Touchscreen) TV Antenna Cable Earphones-Microphone Self Check Forcing Power Off Bluetooth® Function Wi-Fi (Wireless LAN) Handset & Hardware Care Use handset within 5oC - 35oC and 35% - 90% humidity. For use in bathrooms, see "Cautions for Use in a Bathroom." Avoid extreme temperature or direct sunlight.
operation. If your hair is between Earpiece and your ear during calls, Proximity Sensor may not function properly. Display may remain on; touching Display accidentally may end the call. Do not cover Light Sensor or place a sticker/label over it; may hinder ambient light detection, resulting in malfunction of Light Sensor. Handset Earpiece is located at the center of Display upper end.
Insert USIM Card and SD Card into correct openings in correct orientation. USIM Card Insertion/Removal ・Always power off before insertion/removal. ・Set USIM Card in USIM Tray beforehand. Do not insert USIM Card without setting it in USIM Tray. ・Place USIM Card in USIM Tray, noting its orientation; align notches with IC (gold) chip facing up. ・Make sure USIM Card is in USIM Tray. Inserting USIM Tray with USIM Card on its edge may cause damage. ・Do not insert USIM Tray upside down.
・When removing SD Card, lightly push it in and release finger (SD Card pops out slightly); gently pull it out horizontally. Close Card Slot Cap Push Card Slot Cap as shown ( and ) to close, then push it firmly all the way from circled area (○) to hinge as shown ( ) so that there is no gap between handset and Card Slot Cap. Display (Touchscreen) Handset Display is Touchscreen. If Display is wet, wipe it with a soft cloth.
・Place a sticker or shield (commercially-available protective film, privacy protector shield, etc.) on Display In the following cases, Press to turn off Display, Press again to turn on Display and then operate handset. ・Handset operates automatically without touch input ・Handset does not respond to touch input TV Antenna Cable To view or record TV, connect TV Antenna Cable to Earphones-Microphone Jack.
Self Check If handset is unstable, diagnose the cause as follows. In Home Screen, flick hot sheet up (Settings) Useful prompts Self check Follow onscreen Forcing Power Off If handset has stopped processing or won't respond to operation, power off forcibly as follows. (Long Press for at least 8 seconds) Release finger after vibration; handset powers off. Bluetooth® Function SoftBank Corp. is not liable for any damages resulting from data/information leakage due to use of handset Bluetooth® function.
Wi-Fi (Wireless LAN) Wireless LAN (hereafter "Wi-Fi") uses radio waves to enable communication between compatible devices within range. However, it is advisable for the user to configure security settings to avoid risk of data interception. Do not use Wi-Fi near electrical appliances, audiovisual equipment or office automation equipment; may affect Wi-Fi transmission speed, availability, clarity, etc. (Especially when a microwave oven is in use.
General Notes "606SH" here refers to this mobile phone "AQUOS ea." Portrait Rights Copyrights Open Source Software Regulatory Information Description of Accessories Frequency Range of Supported Bands in EU Maximum Transmit Power Battery Cautions Volume Level Caution Stand-by Mark FCC Notice Portrait Rights Portrait rights protect individuals' right to refuse to be photographed or to refuse unauthorized publication/use of their photographs.
rights are protected by copyright laws. Do not copy, modify, alter, disassemble, decompile or reverse-engineer the software; do not separate it from hardware in whole or part. Open Source Software Handset contains software based on GNU General Public License (GPL), GNU Lesser General Public License (LGPL), and other licenses.
Frequency Range of Supported Bands in EU Item Description GSM 900 Tx 880.2 to 914.8 MHz Rx 925.2 to 959.8 MHz DCS 1800 Tx 1710.2 to 1784.8 MHz Rx 1805.2 to 1879.8 MHz WCDMA FDD I Tx 1922.4 to 1977.6 MHz Rx 2112.4 to 2167.6 MHz WCDMA FDD VIII Tx 882.4 to 912.6 MHz Rx 927.4 to 957.6 MHz LTE Band 1 Tx 1922.5 to 1977.5 MHz Rx 2112.5 to 2167.5 MHz LTE Band 3 Tx 1710.7 to 1784.3 MHz Rx 1805.7 to 1879.3 MHz Bluetooth Tx 2402 to 2480 MHz Rx 2402 to 2480 MHz WLAN 2.
Battery Cautions Use specified Charger only. Non-specified equipment use may cause Internal Battery to leak, overheat, burst or ignite, and may cause Charger to overheat, ignite, malfunction, etc. Battery is built into handset. Do not dispose of handset with ordinary refuse; take it to a SoftBank Shop for appropriate disposal. Charge handset in ambient temperature 5oC - 35oC; Internal Battery may leak/overheat and performance may deteriorate outside this range.
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Radio Wave Exposure and Specific Absorption Rate (SAR) Information 【606SH】 here refers to this mobile phone 【AQUOS ea】. Specific Absorption Rate (SAR) for This Product (for Japan) European RF Exposure Information/FCC RF Exposure Information Specific Absorption Rate (SAR) for This Product (for Japan) This mobile phone 【606SH】 meets the Japanese technical regulations* and international guidelines for exposure to radio waves.
* The technical regulation is provided in Article 14-2 of the Ministry Ordinance Regulating Radio Equipment. ** International Commission on Non-Ionizing Radiation Protection *** The value is ●●● under simultaneous transmission use conditions. The World Health Organization has announced that "A large number of studies have been performed over the last two decades to assess whether mobile phones pose a potential health risk.
Hereby, SHARP CORPORATION declares that the radio equipment type 【606SH】 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.sharp.co.jp/k-tai/. ■FCC RF Exposure Information Your handset is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.
World Health Organization http://www.who.int/emf List of Specific Absorption Rates (SAR) for radio waves by smartphone/3G model http://www.softbank.
Water & Dust Resistance Handset Water & Dust Resistance Precautions Cautions for Use in a Bathroom Charging Cautions Care & Maintenance Washing Handset Drying Handset Handset Water & Dust Resistance Handset complies with IPX51 and IPX82 water protection standards as well as IP6X3 dust protection standard, with Card Slot Cap closed firmly. 1 IPX5 compliant means that a handset continues to function as a phone after being subjected to a water jet (approximately 12.5 liters/min.
If handset is wet, wipe it with a dry cloth. Never open/close Card Slot Cap with wet hands or while handset is wet or has a foreign object adhered to it. Do not use Earphones-Microphone Jack or External Connection Jack while it is wet or obstructed by sand/dirt; may affect water and dust resistance or may cause malfunction, burns or fire due to electric shock, short-circuiting, etc. o o Handset is only water resistant against fresh/tap water between 5 C - 35 C.
If handset gets exposed to liquids other than tap water or falls in a bathtub, wash it in the specified way. Use handset at 5oC - 40oC with humidity of 99% or less, for up to 2 hours. Note that this does not guarantee continuous operation of all functions. After exposing handset to water, be sure to remove moisture and let it dry naturally in the way specified in "Drying Handset." Let handset dry naturally after using it in a bathroom or when condensation occurs inside Camera lens, etc.
To maintain water and dust resistance, it is recommended to replace Card Slot Cap every 2 years regardless of its condition. Customer-requested Card Slot Cap replacement incurs fees and requires handset submission. For details, contact a SoftBank Shop or SoftBank Customer Support, General Information. Washing Handset Wipe off dirt, sand, beverage, etc., gently with a cloth. Then hold handset approximately 10 cm below faucet or shower head and wash with low-pressure tap water (6 liters/min.
When shaking handset, hold it firmly so as not to drop it. Pat against dry cloth to remove moisture from openings and grooves Water may be trapped in openings; pat against a dry cloth to remove it.
Leave handset on dry cloth for approximately 2 - 3 hours at room temperature Cautions When Removing Moisture Do not put a cotton swab, cloth, etc. into openings; may affect water and dust resistance. After Drying Procedure Do not use handset in wet conditions. Calls may fail, or moisture may transfer to clothes, bag, etc. Moisture may short-circuit Earphones-Microphone Jack, External Connection Jack or other parts. Exposure to cold may freeze moisture and cause malfunction.
