LC-20S2U-S SERVICE MANUAL S73F4LC-20S2U LCD COLOR TELEVISION MODEL LC-20S2U-S In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. CONTENTS Page » IMPORTANT SERVICE SAFETY PRECAUTION .........................................................................................2 » SPECIFICATIONS ........................................................................
LC-20S2U-S IMPORTANT SERVICE SAFETY PRECAUTION Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow: • Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity or measure the AC voltage drop across the resistor.
LC-20S2U-S PRECAUTIONS A PRENDRE LORS DE LA REPARATION Ë Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. conduite électrique ou une prise de terre branchée à la terre. • Utiliser un voltmètre CA d'une sensibilité d'au moins 5000Ω/V pour mesurer la chute de tension en travers de la résistance.
LC-20S2U-S Precautions for using lead-free solder 1 Employing lead-free solder "All PWBs" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder. Example: LFa Indicates lead-free solder of tin, silver and copper. 2 Using lead-free wire solder When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder.
LC-20S2U-S SPECIFICATIONS Items Model LC-20S2U LCD panel 19.7” Advanced Super View & BLACK TFT LCD Number of dots Video color systems TV Standard (CCIR) TV Tuning System TV function STEREO CATV Y/C FILTER Brightness Lamp life (Fluorescent lamp) Viewing angles Audio amplifier Speakers AV-IN1 AV-IN2 Terminals COMPONENT Antenna Headphone OSD language Power supply Weight 921,600 dots VGA N358, N443, PAL, PAL-M, PAL-N, SECAM, PAL-60 NTSC/PAL-M/PAL-N PLL 181 ch. MTS+SAP 125 ch.
Upper control panel 6 * The examples used throughout this manual are based on the LC-20S2U model. A green indicator lights when the power is on and a red indicator lights when in the standby mode (the indicator will not light when the main power is off). POWER indicator The Optical Picture Control indicator lights up green when the BRIGHTNESS is set to AUTO. OPC indicator (Optical Picture Control) Plug the headphone mini-plug into the HEADPHONE jack located on the front of the TV set.
9 8 6 7 2 3 4 5 1 VOL MUTE DISPLAY SLEEP POWER CH AUDIO ONLY CC ENTER BRIGHT FLASHBACK TV/VIDEO MENU PIC. FLIP REMOTE CONTROL 17 15 16 13 14 12 11 10 7 / / (Cursor control) Select a desired item on the screen. / Set the orientation of the picture. Set the channel. 17 Channel Select Return to the previous channel. 16 FLASHBACK Select a Liquid Crystal Television input source. 15 TV/VIDEO Display Closed Caption subtitles. 14 CC Display the menu screen.
LC-20S2U-S DIMENSIONS Unit: inch (mm) 949/64 (248) 119/64 (283) 1821/32 (474) 3 /16 (5) 9 (228.5) 43/64 (103) 1 /32 (1) 185/8 (473) 55/32 (131) 821/32 (220) 8 127/32 ( (47) 315/16 (100) 315/16 (100) 73/16 (182.5) 243/64 (68) 185/8 (473) 1127/32 (300.8) 163/16 (411) 157/8 (403.
LC-20S2U-S REMOVING OF MAJOR PARTS 1. Remove the stand fixing screws (4 pcs.). 2. Remove the terminal cover. 3. Remove the terminal section fixing screws (3 pcs.). 4. Remove the cabinet B fixing screws (9 pcs.). 5. Remove the cabinet B after opening from the direction of an arrow. 6. Remove the reinforcement angle fixing screws (2 pcs.). 8. Detach the connector from each PWB.
LC-20S2U-S 8. Remove the 3 lock screws from the main PWB and undo the hooks a and b. Lifting the other PWBs close to the hooks, draw out the main PWB. 9. Remove the 4 lock screws from the sub PWB and undo the hooks c and d. Detach the chassis frame (right), together with its terminals, from the sub PWB. Undo the hooks e and f in the same way. Detach the chassis frame (left), together with its terminals, from the sub PWB. 10. Remove the 3 lock screws from the inverter PWB and take out the inverter PWB. 11.
LC-20S2U-S » Precautions in handling the LCD panels 1. Work in a clean room (with humidities below 50%). 2. Be sure to wear an anti-static armband. 3. Handle the panels on an electro-conductive mat. 4. Be careful not to fall, shake and shock the panels. 13. Remove the 3 lock screws from the LCD panel and detach the LCD panel. 14. Remove the reflection/polarization sheet, prism sheet, diffusion sheet and diffusion panel. 15. Detach the lamp holders (top)-A, (top)-B and (bottom) from the lamp unit assembly.
LC-20S2U-S Precautions at the time of the side B(back) service of Main unit. 1. Remove the FFC for connection between Main unit (SC2001) and Sub unit(SC3401), and connect the extended cable (QCNW-A556WJZZ) for service. 2. Remove only SC1204 of the FFC for connection between Main unit (SC1204) and LCD panel unit, and connect the extended cable (QCNW-A553WJZZ) for service. 3.
LC-20S2U-S ADJUSTING PROCEDURE OF EACH SECTION 1. Pre-adjustment preparations Use the specific AC adaptor or a stable DC power supply as power source. LC-13/15/20S2U AC adaptor: UADP-A044WJPZ DC power supply: 12V, 5.0A (1) Entering the adjustment process mode There are two ways to call this mode. » Press "MENU" and "INPUT SELECT" at once, and the power is turned on (inspection process started). Then press "CHANNEL DOWN" and "VOLUME DOWN" at once.
LC-20S2U-S 2. Adjusting procedure (1) Getting initialized 1) Set pins (81) and (82) of the IC2001 microprocessor to GND. Turn on the power. 2) Make sure the model number is A622. * Note: The model number cannot be selected. 3) Select the screen size (13/15/20 inches). Select the inch size according to the 20" model. (2) +B adjustment 1) Receive the standard color bar signal. 2) Rotate R3710 (semi-fixed variable resistor) to adjust the voltage at pin (4) of P3701 on the sub PWB to 5.00V±0.02V.
LC-20S2U-S (5) Factory settings 1) Starting the factory process mode Press "MENU" and "INPUT SELECT" at once, and the power is turned on (inspection process started). Then press "CHANNEL UP" and "VOLUME UP" at once. Note: Once the factory settings have been made, immediately turn off the power switch. (At the next power-on, the set gets started in the "EZ SETUP" mode. If an unnecessary key input is added after the factory settings, the set may malfunction.
LC-20S2U-S 3. Test patterns in adjustment process mode (1) IC801 (Video decoder) test patterns 1) Getting the test patterns displayed Put the screen in AV1, AV2 or COMPONENT but keep out any signal. Call the adjustment process mode, select "TEST PAT MODE" in the 1st line of XVC 1, make the settings 1 thru 12, and the following test patterns show up.
LC-20S2U-S Pin functions of microprocessor IC (IC2001) RH-iXA622WJZZQ Pin No.
LC-20S2U-S Pin No. 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 I/O I O O O I O I O O O O I O O O O O O O O O O I O O O O O O O I I O O O O I I I I I I I O I I/O I I I I Pin Name SSW2 HPMUTE SP MUTE 1 CVBS/Y HP DET SSTBY VSH IN LMUTE V IN/OUT SRESET C IN/OUT HSYNC MIX.
LC-20S2U-S Table of Adjusting Process Defaults Page No. Item Initial Value Function Response precautions on servicing (Do not change other items than designated.) Basic settings 1 MODEL A622 Model name selection (For prevention of malfunction, model name cannot be changed.
LC-20S2U-S Page No. SOUND3 Item BASS EQ SET TREB EQ SET EQ LIMIT 00 EQ LIMIT 00 EQ LIMIT 01 EQ LIMIT 01 EQ LIMIT 02 EQ LIMIT 02 EQ LIMIT 03 EQ LIMIT 03 EQ LIMIT 04 EQ LIMIT 04 EQ LIMIT 05 EQ LIMIT 05 EQ LIMIT 06 EQ LIMIT 06 EQ LIMIT 07 EQ LIMIT 07 EQ LIMIT 08 EQ LIMIT 08 EQ LIMIT 09 EQ LIMIT 09 EQ LIMIT 10 EQ LIMIT 10 EQ LIMIT 11 EQ LIMIT 11 EQ LIMIT 12 EQ LIMIT 12 EQ LIMIT 13 EQ LIMIT 13 EQ LIMIT 14 EQ LIMIT 14 EQ LIMIT 15 EQ LIMIT 15 Initial Value Function 0 0 00 +12.0 10 +12.0 20 +12.0 25 +12.
LC-20S2U-S Page No.
LC-20S2U-S Page No.
LC-20S2U-S Page No.
LC-20S2U-S Page No.
LC-20S2U-S Page No.
LC-20S2U-S Page No.
LC-20S2U-S Page No.
LC-20S2U-S Page No. DPS11 Item PAL-N TV COLOR PAL-N AV COLOR Initial Value Function 30 Color depth setting (TV) 30 Color depth setting (Composite, S Video, Response precautions on servicing (Do not change other items than designated.) Not used. Not used. for component 480I) PAL-N TV TINT PAL-N AV TINT 0 Color tone setting (TV) 0 Color tone setting (Composite, S Video, Not used. Not used.
LC-20S2U-S Page No.
LC-20S2U-S Page No.
LC-20S2U-S Page No.
LC-20S2U-S Page No. Item DPS47 NTSC TV LMIX78 NTSC AV LMIX78 DPS48 NTSC TV BLEMODE NTSC AV BLEMODE Initial Value Function 79 Variable mixing mode setting (TV) 79 Variable mixing mode setting (Composite, Response precautions on servicing (Do not change other items than designated.) Not used. Not used. S Video, for component 480I) 3 Black extension setting (TV) 3 Black extension setting (Composite, Not used. Not used.
LC-20S2U-S Page No. DPS52 Item PAL TV BLEMODE PAL AV BLEMODE Initial Value Function 3 Black extension setting (TV) 3 Black extension setting (Composite, Response precautions on servicing (Do not change other items than designated.) Not used. Not used. S Video, for component 480I) PAL TV BGAINREF71 PAL AV BGAINREF71 199 Black extension gain setting (TV) 199 Black extension gain setting (Composite, Not used. Not used.
LC-20S2U-S Page No. DAC DAC 1 DAC 2 DAC 3 TUNER TUNER1 Item V0 H V0 L V7 H V7 L V21 H V21 L V64 H V64 L V112 H V112 L V176 H V176 L V235 H V235 L V255 H V255 L COM H COM L VGL COM H VGL COM L VGL ADJ 240 30 212 52 197 67 181 82 159 100 124 133 20 235 0 255 182 0 215 0 0 AFT UP AFT DOWN LSYNC HSYNC AVSYNC AIR SERCH SYSTEM 1.8 1.2 625 655 5000 1.
LC-20S2U-S PUBLIC MODE SETTING PROCEDURE 1. How to start Public Mode » There are the following two ways to get the public mode setup screen displayed. 1 In the adjustment process mode, turn on "PUBLIC MODE". Also press the [CH UP] and [VOL+] keys on the set at once and turn on the power. 2 1) Press the [MENU] and [VOL+] keys on the set at once and turn on the power. 2) Get the password input screen displayed. Procedure » The input starts with the leftmost digit.
LC-20S2U-S 2. How to exit Public Mode There are the following ways to quit the public mode setup screen. » Turn off "PUBLIC MODE" in the adjustment process mode. (✩) ← This way alone is not for quitting the setup screen, but for quitting the mode itself. » Turn off the power with the power key. (★) » Select "EXECUTE". (★) » Move the cursor to "RESET" and press the "FLASHBACK" key. (Back to the normal mode screen)(✩) ★ ... "PUBLIC MODE" stays on in the adjustment process mode. ✩ ...
LC-20S2U-S 5. On Setting Items * "EZ-SETUP" discussed below indicates "EZ-SETUP after the first power-on". (1) MAXIMUM VOLUME Selection Default Function Exception Remarks Adjustable from 1 to 60 (no loop) 60 The volume control is limited to an adjusted level (for the main speakers and headphones). » The VOLUME setting can be freely adjusted to a desired level in the adjustment process mode. » The volume can be preset from -60 to 0 in the line output regardless of the adjusted setting.
LC-20S2U-S (5) MENU BUTTON Selection Default Function Exception Selection between "RESPOND" and "NO RESPOND" (loop provided) RESPOND Disabling the MENU key both on the set and the remote controller » The MENU button is operative at a start of inspection process and public password regardless of this setting. (See Note in (4) above.
LC-20S2U-S (8) INPUT MODE FIXED Selection Default Function Selection between "VARIABLE" and "FIXED" (loop provided) VARIABLE In the "FIXED" setting, the "START MODE" setting is forced up, which disables the switching to other channels and input sources.
LC-20S2U-S Sound only mode function specifications 1 Behavior of the remote control BRIGHT button. BRIGHTNESS [BRIGHT]→BRIGHTNESS [NORMAL]→ BRIGHTNESS [DARK]→BRIGHTNESS [AUTO]→BRIGHTNESS [OFF]→BRIGHTNESS [BRIGHT] (The "OFF" setting is added while the remote control BRIGHT button is effective. With "YES" selected in "SOUND ONLY MODE".) 2 When the "OFF" mode is selected, the screen becomes mute, the following message appears and the time is counted down.
LC-20S2U-S Table of Key Allocation in Sound Only Mode (Unit keys/Remote control keys) Unit keys Remote control Key POWER TV/VIDEO MENU CH VOL POWER PIC.
Check IC801 and its peripheral circuits. Check the IC801 signal input line. No Check the related lines, IC801 itself and its peripheral circuits. Are the waveforms at pins (8), (9), 26), and (27) of IC1201 as specified? Yes No No Check IC1201 and its peripheral circuits as well as the LCD panel voltage and waveform. Check the IC801 signal output line, IC801 itself and its peripheral circuits.
Are inputs and outputs of IC801 as specified? Yes No Check IC3402 and its peripheral parts. Check IC801 and its peripheral circuits. Does the video decoder No test pattern appear? Yes Check IC1201, its peripheral circuits and the LCD panel. Does the LCD controller test No pattern appear? No picture at all No 43 Check IC3402 and its peripheral parts.
No No Check SC OUT1LINE and IC8201, Q8205, IC811, Q8202 No No S-VIDEO color No color Check S4053 and connection cable. Replace F3701. Check SC3411, SC3412, SC line and peripheral parts. No Is input at Pin (116) of IC801 as specified? No No Interlace No COMPONENT color Replace the fluorescent lamp and check the oscillation waveform again.
Check the speakers and their peripheral parts. Yes Are inputs at pins (2) and (4) as well as outputs at pins (8) and (12), all of IC3305, as specified? Yes Are outputs at pins (1) and (7) of IC3302/ IC3303/IC3304 as specified? Yes Are input and output of IC3301 as specified? Yes Is pin (53) of IC2001 at “L”? No sound from speakers No No No No Check the line in question, IC3305 and its peripheral parts. Check IC3302, IC3303, IC3304 and their peripheral parts.
LC-20S2U-S CHASSIS LAYOUT INVERTER Unit H SUB Unit G F E D C B R/C, LED Unit A 1 2 3 4 5 6 46 7 8 9 10
LC-20S2U-S MAIN Unit 10 11 12 13 14 15 47 16 17 18 19
LC-20S2U-S BLOCK DIAGRAM H G F E D C B A 1 2 3 4 5 6 48 7 8 9 10
LC-20S2U-S 10 11 12 13 14 15 49 16 17 18 19
LC-20S2U-S OVERALL WIRING DIAGRAM H G F E D C B A 1 2 3 4 5 6 50 7 8 9 10
LC-20S2U-S 10 11 12 13 14 15 51 16 17 18 19
LC-20S2U-S DESCRIPTION OF SCHEMATIC DIAGRAM VOLTAGE MEASUREMENT CONDITION: 1. The voltages at test points are measured on exclusive AC adaptor and the stable supply voltage of AC 120V. Signals are fed by a color bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester. INDICATION OF RESISTOR & CAPACITOR: RESISTOR 1. The unit of resistance “Ω” is omitted. (K=kΩ=1000 Ω, M=MΩ). 2. All resistors are ± 5%, unless otherwise noted. (J= ± 5%, F= ± 1%, D= ± 0.5%) 3.
LC-20S2U-S SCHEMATIC DIAGRAM Ë R/C, LED Unit H G F E D C B A 1 2 3 4 53 5 6
LC-20S2U-S ËMAIN Unit-1/6 H G F E D C B A 1 2 3 4 5 6 54 7 8 9 10
LC-20S2U-S 10 11 12 13 14 15 55 16 17 18 19
LC-20S2U-S ËMAIN Unit-2/6 H G F E D C B A 1 2 3 4 5 6 56 7 8 9 10
LC-20S2U-S 10 11 12 13 14 15 57 16 17 18 19
LC-20S2U-S ËMAIN Unit-3/6 H G F E D C B A 1 2 3 4 5 6 58 7 8 9 10
LC-20S2U-S 10 11 12 13 14 15 59 16 17 18 19
LC-20S2U-S ËMAIN Unit-4/6 H G F E D C B A 1 2 3 4 5 6 60 7 8 9 10
LC-20S2U-S 10 11 12 13 14 15 61 16 17 18 19
LC-20S2U-S ËMAIN Unit-5/6 H G F E D C B A 1 2 3 4 5 6 62 7 8 9 10
LC-20S2U-S 10 11 12 13 14 15 63 16 17 18 19
LC-20S2U-S ËMAIN Unit-6/6 H G F E D C B A 1 2 3 4 5 6 64 7 8 9 10
LC-20S2U-S 10 11 12 13 14 15 65 16 17 18 19
LC-20S2U-S ËSUB Unit-1/4 H G F E D C B A 1 2 3 4 5 6 66 7 8 9 10
LC-20S2U-S 10 11 12 13 14 15 67 16 17 18 19
LC-20S2U-S ËSUB Unit-2/4 H G F E D C B A 1 2 3 4 5 6 68 7 8 9 10
LC-20S2U-S 10 11 12 13 14 15 69 16 17 18 19
LC-20S2U-S ËSUB Unit-3/4 H G F E D C B A 1 2 3 4 5 6 70 7 8 9 10
LC-20S2U-S 10 11 12 13 14 15 71 16 17 18 19
LC-20S2U-S ËSUB Unit-4/4 H G F E D C B A 1 2 3 4 72 5 6
LC-20S2U-S ËINVERTER Unit H G F E D C B A 1 2 3 4 73 5 6
LC-20S2U-S PRINTED WIRING BOARD ASSEMBLIES H G F E D C B A MAIN Unit (Side-A) 1 2 3 4 74 5 6
LC-20S2U-S H R2120 TP2002 SC2001 TP2053 R2041 R2017 FDC001 R2063 IC2001 R2118 Q2009 R2019 R2021 R2112 Q2003 R2027 R2022 R2093 C702 C705 C720 C713 R717 P701 C712 IC704 C861 C1231 C1235 C708 C709 C1232 P1201 C864 R1213 R1210 C1208 C833 R859 IC807 R1227 C1212 C1214 IC1201 C1211 C1213 C825 R1224 TP2001 C802 R1267 C1217 R1228 C1216 C823 R1231 C1215 R1232 R1268 C1242 R1236 C1223 C1222 C1221 C1220 C1218 R1235 R2012 R2043 R2047 R2025 Q703 C736 R1215 R
LC-20S2U-S H G F E D C B A MAIN Unit (Side-B) 1 2 3 4 76 5 6
1 2 Q1206 R1261 3 77 R1256 D1202 D1204 R1257 4 R854 R1255 R1254 R1204 C1239 R1250 R1265 C1240 R1266 R845 C876 R1122 R850 R849 R2001 R2003 C2005 C2007 R1111 R1115 Q1101 R1113 5 TL2051 TL2046 TL2049 R2130 TL2052 TL2045 TL2048 TL2047 TL2050 R1110 C1113 C1112 Q1104 C739 R1108 L8209 R2005 R2002 R8227 R8223 Q8205 TL2044 R8215 R1127 C801 R1109 C2009 L8204 Q8207 TP8201 TP8202 C8238 C8235 R8222 C8219 Q8210 R8231 R2057 R1128 TL1212 TL1220 TL1209 TL1276 TL1216 TL1222 D
LC-20S2U-S H G F E D C B A 1 2 3 4 5 6 78 7 8 9 10
LC-20S2U-S SUB Unit (Side-A) 10 11 12 13 14 15 79 16 17 18 19
LC-20S2U-S R4051 D4050 H R4050 SW4052 SW4051 SW4055 SW4050 TP3003 SW4054 C3710 R3337 D4051 R3336 R3339 J3401 R3762 R3761 S4053 R4052 R3335 D3711 C3727 R3737 L3202 C3716 L3701 C3325 C3731 R3338 L3704 R3774 T3701 D3708 R3707 C3738 C3732 R3738 L3301 IC3702 C3740 R3734 C3737 C3744 Q3711 C3304 R3766 C3742 R3755 R3387 C3385 C3387 R3368 R3386 R3311 C3389 R3398 Q3713 R3310 C3305 R3388 R3312 R3343 R3753 R3751 C3739 C3201 L3702 R3764 R3756 C3743 L8402
LC-20S2U-S R4053 SW4056 D4052 SW4055 0 P6500 R4052 T6500 P6501 Q6501 C6510 Q6500 R6510 R6501 Q6506 L3703 R6509 Q6502 R6512 C3734 R3733 C6505 Q6507 R6516 L6503 Q6504 C6508 Q6503 R6515 R6506 R6514 C3736 R6504 C6512 R6513 R3777 P3604 P3701 C3737 R3771 R3767 R3750 R3768 R3770 R3769 Q3714 L3302 C3757 FH6501 C3339 FH6503 C3343 C3341 C3342 C3344 C3345 C3350 C3346 C3349 C8466 C3024 D3304 C3356 C3338 C3333 C3337 D3305 R3357 R3304 IC3301 C3348 C3357 D33
LC-20S2U-S H G F E D TL6018 TL6707 R6714 R6746 R6750 R6756 IC6702 R6738 R6736 R6735 R6739 R6737 R6741 R6704 D6701 R6751 D6702 C6713 R6717 A Q6708 C6714 Q6709 R6713 R6712 R6709 R6706 C6708 Q6705 C6706 C6715 R6716 R6715 Q6703 Q6704 R6705 R6745 R6707 R6755 IC6701 C6710 R6711 C6702 Q6702 82 10 9 8 7 6 5 4 C6707 R6710 Q6706 IC6700 R6744 R6701 Q6701 Q6700 D6703 R6708 D6704 R6700 C6711 C6701 R6749 R6702 R6754 C6703 TL6021 D6700 R6703 TL6
LC-20S2U-S INVERTER Unit (Side-A) TL6716 TL6715 TL6712 TL6713 TL6031 TL6714 TL6720 TL6030 TL6717 TL6721 TL6032 TL6722 TL6027 TL6022 R6729 R6732 C6727 R6728 Q6716 Q6717 R6733 C6719 C6720 Q6712 R6720 R6721 R6726 R6727 R6734 Q6710 Q6711 C6726 C6729 Q6714 Q6715 R6730 R6719 R6723 D6710 D6711 C6718 D6705 R6725 Q6707 Q6708 C6714 Q6709 R6716 R6715 Q6713 C6713 R6717 C6722 TL6026 C6725 R6748 R6731 R6718 R6747 IC6703 R6757 R6752 D6707 R6722 D6709 C6723 R671
LC-20S2U-S H G F R/C, LED Unit (Side-A) (QPWBSB982WJN1) E D P4001 P4003 D4007 R4002 D4001 R4007 Q4002 R4005 D4002 R4003 D4006 B Q4003 R4001 R4008 Q4001 Q4004 D4004 J4021 R4009 IC4201 D4005 C4001 RMC4001 C4203 C4201 C R4006 D4008 C4202 R/C, LED Unit (Chip Parts Side-A) (QPWBSB982WJN1) A 1 2 3 4 84 5 6
LC-20S2U-S Ref. No. Part No. ★ Description Code PARTS LIST Ref. No. ★ Part No. Description LISTE DES PIECES Code PARTS REPLACEMENT CHANGE DES PIECES Replacement parts which have these special safety characteristics identified in this manual ; electrical components having such features are identified by å and shaded areas in the Replacement Parts Lists and Schematic Diagrams.
LC-20S2U-S Ref. No. ★ Part No. Description Code Ref. No.
LC-20S2U-S Ref. No. Part No. ★ Description Code Ref. No.
LC-20S2U-S Ref. No. ★ Part No. Description Code Ref. No.
LC-20S2U-S Ref. No. Part No. ★ Description Code Ref. No.
LC-20S2U-S Ref. No. FB8202 FB8203 FB8204 FB8206 FB8210 FB8211 P701 P1201 P2001 SC1202 SC1203 SC1204 SC2001 TP2002 TP2052 TP2053 Part No. ★ Description Code Ref. No. ★ Part No.
LC-20S2U-S Ref. No. ★ Part No. Description Code Ref. No.
LC-20S2U-S Ref. No. ★ Part No. Description Code Ref. No.
LC-20S2U-S Ref. No. Part No. ★ Description Code Ref. No.
LC-20S2U-S Ref. No. ★ Part No. Description Code Ref. No. ★ Part No.
LC-20S2U-S Ref. No. ★ Part No. Description Code Ref. No. DUNTKB983WJ03 INVERTER Unit (Continued) C6727 VCKYCY1CB333KY J 0.
LC-20S2U-S Ref. No. Part No. ★ Description Code Ref. No.
LC-20S2U-S CABINET AND MECHANICAL PARTS H 1 1-2 A 1-3 13 1-4 M A 1-1-4 1-1-6 1-1-1 D 1-1-3 G 1-1-2 1-1-5 5-3-5 5-3-4 B E 1-4 5-3-2 1-3 5-3-1 5-3-7 C 5-3-6 1-1-3 5-3-3 O 1-1 13 F K 5-3-8 A A 26 F R/C,LED 5-3-4 B Q 5-4 5-2 5-2-1 B 5-3 5-2 5-2-1 E 5-2 5-2-1 5-10 5-2 5-2-1 5-2 5-2-1 G 6 4-4 5-5 5-13 D 2-4 5-9 5-11 5-8 5-1 H I 2-7 2-10 5-6 5-12 10 4 20 2-5 4-1 5-7 B 12 A 5 22 2-1 5-13 2-2 4-8 14 25 4-2 4-7 4-6 4-5 J C 4-3 N 16 11
LC-20S2U-S Ref. No. Part No. ★ Description Code Ref. No.
LC-20S2U-S PACKING OF THE SET Operation Manual (TiNS-A966WJZZ) Cable Clamp (2pcs.) (LHLDWA002WJSB) Questionnaire Card (TCADEA028WJZZ) ★ "AAA" size Battery (2pcs.
LC-20S2U-S COPYRIGHT © 2003 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. TQ1614-S Sep. 2003 Printed in Japan Design and Production Information Design : Japan Production : SEMEX MI.
