MODEL: MX-C310 MX-C380 MX-C311 MX-C381 MX-C400 DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM Maintenance & Safety Guide Please read first Please read this guide first to ensure safe use of the machine. Before installing this product, be sure to read the "TO ENSURE SAFE USE OF THE MACHINE" and "INSTALLATION REQUIREMENTS" sections.
Each instruction also covers the optional units used with these products. Caution! For complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations. ➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢ The equipment should be installed near an accessible socket outlet for easy disconnection.
EMC (this machine and peripheral devices) Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. For the users of the fax function FAX interface cable and Line cable: These special accessories must be used with the device. The Declaration of Conformity can be viewed at the following URL address. http://www.sharp.de/doc/MX-FXX3.
Contents TO ENSURE SAFE USE OF THE MACHINE . . . . . . . . . . . . . . . . . . 4 Cautions . . . . . . . . . . . . . . . . . . . 4 Warnings . . . . . . . . . . . . . . . . . . 5 Laser information . . . . . . . . . . . . 7 INSTALLATION REQUIREMENTS . . . 8 SUPPLIES. . . . . . . . . . . . . . . . . 10 Storage of supplies. . . . . . . . . . 10 Supply of spare parts and consumables . . . . . . . . . . . . . . 10 REPLACING SUPPLIES AND MAINTENANCE . . . . . . . . . . . . 11 Replacing the toner cartridges .
Note: • Considerable care has been taken in preparing this manual. If you have any comments or concerns about the manual, please contact your dealer or nearest authorised service representative. • This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect or other problem is discovered, please contact your dealer or nearest authorised service representative.
TO ENSURE SAFE USE OF THE MACHINE Cautions • Do not make any modifications to this machine. Doing so may result in personal injury or damage to the machine. • Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from printing by national law. Other items may be prohibited by local law. ● Money ● Stamps ● Bonds ● Stocks ● Bank drafts ● Checks ● Passports ● Driver's licences • Do not use a flammable spray to clean the machine.
TO ENSURE SAFE USE OF THE MACHINE Warnings • Do not touch the transfer belt and the transfer roller. Scratches or smudges on the transfer belt or transfer roller will cause dirty prints. • The fusing unit is extremely hot. Exercise care in this area. • Do not look directly at the light source. Doing so Fusing unit may damage your eyes. • The machine is heavy. To prevent injury when moving the machine, it is recommended that it be moved by four or more persons.
TO ENSURE SAFE USE OF THE MACHINE The machine includes the document filing function, which stores document image data on the machine's hard drive. Stored documents can be called up and printed or transmitted as needed. If a hard drive failure occurs, it will no longer be possible to call up the stored document data. To prevent the loss of important documents in the unlikely event of a hard drive failure, keep the originals of important documents or store the original data elsewhere.
TO ENSURE SAFE USE OF THE MACHINE Laser information Wave length 790 nm ±10 nm Pulse times (North America and Europe) 4.1 µs ±4.1 ns /7 mm Output power Max 0.6 mW (LD1+ LD2) Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 1.
INSTALLATION REQUIREMENTS Improper installation may damage this product. Please note the following during initial installation and whenever the machine is moved. 1. The machine should be installed near an accessible power outlet for easy connection. 2. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded.
INSTALLATION REQUIREMENTS CAUTION: Do not install the machine in a location with poor air circulation. A small amount of ozone is created inside the machine during printing. The amount of ozone created is not sufficient to be harmful; however, an unpleasant odor may be noticed during large copy runs, and thus the machine should be installed in a room with a ventilation fan or windows that provide sufficient air circulation. (The odor may occasionally cause headaches.
SUPPLIES Standard supplies for this product that can be replaced by the user include paper, toner cartridges, and staple cartridges for the finisher. Be sure to use only SHARP-specified products for the toner cartridges, finisher staple cartridge, and transparency film. For best copying results, be sure to use only Sharp Genuine Supplies which are designed, engineered, and tested to maximize the life and performance of Sharp products. Look for the Genuine Supplies label on the toner package.
REPLACING SUPPLIES AND MAINTENANCE This section explains the procedures for replacing supplies such as toner and staple cartridges and routine maintenance. Replacing the toner cartridges Be sure to replace the toner cartridge when the message "Change the toner cartridge." appears. In copy mode Ready to scan for copy. ( Change the toner cartridge.) When the message appears in the message display, replace the toner cartridge for the indicated colour.
REPLACING SUPPLIES AND MAINTENANCE Open the front cover. Locations of colour toner cartridges 1 (Y) (M) (C) (Bk) (Y): Yellow (M): Magenta (C): Cyan (Bk): Black Pull the toner cartridge toward you.
REPLACING SUPPLIES AND MAINTENANCE Take out the new toner cartridge, hold it with both hands, and shake 5 or 6 times horizontally. Protective material 3 • When shaking the toner cartridge, be sure to shake with the protective material inserted in the cartridge. If you shake the cartridge after removing the protective material, toner may spill out. • Shake the toner cartridge only in the horizontal direction. If shaken in any other direction, toner may collect in one part of the cartridge.
REPLACING SUPPLIES AND MAINTENANCE Insert the new toner cartridge horizontally and push it firmly in. The shape of the toner cartridge varies by colour. Insert in the same location as the toner cartridge that was removed.
REPLACING SUPPLIES AND MAINTENANCE Close the front cover. 6 • After the toner cartridge is replaced, the machine automatically enters image adjustment mode. Image adjustment will not take place if the cover is not closed. • Take care that your fingers are not pinched when closing the cover. Caution • Do not throw a toner cartridge into a fire. Toner may fly and cause burns. • Store toner cartridges out of the reach of small children.
REPLACING SUPPLIES AND MAINTENANCE Replacing the toner collection container The toner collection container collects excess toner that is produced during printing. When the toner collection container becomes full, "Replace used toner container." will appear. Follow the procedure below to replace the toner collection container. It is also necessary to remove the toner collection container in order to replace the transfer unit.
REPLACING SUPPLIES AND MAINTENANCE Remove the toner collection container. 3 • If the toner collection container is tipped forward too far, it will not be possible to remove it. • Do not point the holes down as used toner will spill out. • Hold the container by both hands and lift it up slowly. • Do not discard the toner collection container. Place it in a plastic bag and keep it until your service technician comes to perform maintenance. Your service technician will collect the toner collection container.
REPLACING SUPPLIES AND MAINTENANCE Turn the lock lever on the toner collection container to the left. Turn the lock lever to the left until it stops. 5 If the lock lever does not turn, check if the toner collection container is installed correctly. In particular, make sure that the top left corner of the toner collection container is correctly in place. Close the front cover. 6 Take care that your fingers are not pinched when closing the cover.
REPLACING SUPPLIES AND MAINTENANCE Replacing the developer cartridge / drum cartridge Before replacing the developer cartridge or drum cartridge, turn off the main power of the machine and wait briefly. Replacing the developer cartridge Your service technician will replace the developer cartridge. Only replace the cartridge as explained below if your service technician instructs you to. Follow the instructions carefully.
REPLACING SUPPLIES AND MAINTENANCE Open the main charger cover. (1) Turn the main charger cover lock levers in the direction of an arrow below. When the lock levers are horizontal, the lock is released. 3 (2) Grasp the lock levers and tip the cover forward.
REPLACING SUPPLIES AND MAINTENANCE Remove the developer cartridge. (1) Grasp the developer cartridge lock and pull it forward and down. (2) Squeeze the lever on the developer cartridge. (3) Pull the developer cartridge out horizontally. (3) 4 (2) (2) (4) Support the developer cartridge near the middle with your hand and completely remove the developer cartridge. Roller • When removing the developer cartridge, grasp it with both hands at the middle.
REPLACING SUPPLIES AND MAINTENANCE Shake the new developer cartridge 5 or 6 times as shown. Hold the developer cartridge firmly as shown below and shake forward and back, left and right. Remove the protective material after shaking the developer cartridge. Protective material 5 • The part of the developer cartridge shown in the next illustration is easily deformed or damaged. Do not touch this part when handling the cartridge. • Do not touch the roller in the developer cartridge.
REPLACING SUPPLIES AND MAINTENANCE Insert the new developer cartridge horizontally. Insert the new developer cartridge in the same location as the cartridge that was removed. 6 • Do not tilt the developer cartridge or insert it in the wrong direction or orientation. This may damage the developer cartridge or drum cartridge and cause failure. • When inserting the developer cartridge, grasp it with both hands at the middle.
REPLACING SUPPLIES AND MAINTENANCE Hold the developer cartridge with one hand and slowly remove the seal with the other hand. Slowly pull the seal straight and horizontally out. 8 If excessive force is used or the seal is pulled out diagonally, it may tear. There is a mark (red belt) on the end of the seal. After removing the seal, be sure to verify that the mark (red belt) is on the end of the seal. If the seal has been cut on the developer cartridge, the cartridge cannot be used.
REPLACING SUPPLIES AND MAINTENANCE Install the toner collection container. ☞ Replacing the toner collection container (page 16) 10 (2) (1) Close the front cover. 11 Take care that your fingers are not pinched when closing the cover.
REPLACING SUPPLIES AND MAINTENANCE Turn on the power. Switch the main power switch "ON" and press the [POWER] key ( operation panel to turn on the operation panel power. ) on the 12 Caution • Do not throw the developer cartridge into a fire. Toner may fly and cause burns. • Store the developer cartridge out of the reach of small children. • When replacing the developer cartridge, be aware that it may soil your clothes or the immediate surroundings.
REPLACING SUPPLIES AND MAINTENANCE Replacing the drum cartridge Your service technician will replace the drum cartridge. Only replace the cartridge as explained below if your service technician instructs you to. Follow the instructions carefully. • Do not leave the drum cartridge outside of its package for a long time, and do not remove cartridge from its package in a location where there is bright sunlight or bright light. This may cause a failure.
REPLACING SUPPLIES AND MAINTENANCE Remove the protective material from the drum cartridge and slowly insert the drum cartridge along the guides. Make sure that the mark on the drum cartridge is aligned with the on the machine as you insert the drum cartridge. 3 mark Drum • To remove the protective material, slowly pull it straight out so that it does not tear. • When installing the drum cartridge, do not touch or damage the drum. This may cause a failure.
REPLACING SUPPLIES AND MAINTENANCE Replacing the staple cartridge in the finisher When the staple cartridge runs out of staples, a message will appear in the operation panel. Follow the procedure below to replace the staple cartridge. Open the cover. 1 While pressing the lever over to the left, slide the finisher to the left until it stops. Gently slide the finisher until it stops 2 Lower the staple case release lever and remove the staple case. Pull the staple case out to the right.
REPLACING SUPPLIES AND MAINTENANCE Remove the empty staple cartridge from the staple case. Gently grasp the right side of the staple cartridge as shown and lift to the left and up. The lock will release easily. After the lock releases, continue lifting the staple cartridge to the left and up to remove it. 4 • Even when a message appears in the operation panel, staples may occasionally remain in the staple cartridge. • If staples remain, the lock will not release easily.
REPLACING SUPPLIES AND MAINTENANCE Replace the staple case. Push the staple case in until it clicks into place. 6 Slide the finisher back to the right. Gently slide the finisher back to the right until it locks into its original position. 7 Close the cover. 8 Take care that your fingers are not pinched when closing the cover. Make a test print or copy in staple sort mode to verify that stapling takes place correctly.
REPLACING SUPPLIES AND MAINTENANCE Regular maintenance To ensure that the machine continues to provide top quality performance, periodically clean the machine. Warning Do not use a flammable spray to clean the machine. If gas from the spray comes in contact with hot electrical components or the fusing unit inside the machine, fire or electrical shock may result. • Do not use thinner, benzene, or similar volatile cleaning agents to clean the machine. These may degrade or discolour the housing.
REPLACING SUPPLIES AND MAINTENANCE Scanning area If coloured lines or white lines appear in images scanned using the automatic document feeder, clean the scanning area (the thin long glass next to the document glass). Cleaning the main charger of the photoconductive drum If black lines or coloured lines appear even after you have cleaned the document glass and automatic document feeder, use the charger cleaner to clean the main charger.
REPLACING SUPPLIES AND MAINTENANCE Release the lock levers and open the main charger cover. ☞ Replacing the developer cartridge (page 19) 3 Remove the charger cleaner. (1) Flip down the charger cleaner lock (A) in the direction of the arrow, and lift the left end of the charger cleaner. (1) 4 (2) (A) (2) Move the charger cleaner to the left and pull it out.
REPLACING SUPPLIES AND MAINTENANCE Clean the main charger. (1) Gently push the charger cleaner all the way in. (2) Gently pull the charger cleaner out. (3) Repeat the above (1) to (2) three times. 5 • Take care not to let the tip of the charger cleaner become soiled by toner. • Clean with the mark ( ) on the charger cleaner facing down. • Holes to be cleaned by the charger cleaner are indicated by labels similar to (A).
REPLACING SUPPLIES AND MAINTENANCE Repeat step 5 with each of the other main chargers. 6 Main charger There are a total of 4 places to be cleaned in the machine as shown. Replace the charger cleaner in its original position. Insert the tip of the charger cleaner in toward the right and then press down on the end of the charger cleaner. The charger cleaner will lock into place. 7 (2) (1) Close the main charger cover and rotate the lock levers in the direction of the arrows to lock the cover.
REPLACING SUPPLIES AND MAINTENANCE Install the toner collection container. ☞ Replacing the toner collection container (page 16) 9 (2) (1) Close the front cover. 10 Take care that your fingers are not pinched when closing the cover. Turn on the power. Switch the main power switch "ON" and press the [POWER] key ( operation panel to turn on the operation panel power.
REPLACING SUPPLIES AND MAINTENANCE Cleaning the bypass tray rollers If you find that paper fed from the bypass tray misfeeds or is soiled by the roller, remove and clean the roller. If misfeeds or soiling continue to occur, replace the roller. Before starting, remove the paper from the bypass tray. Press the [POWER] key ( ) on the operation panel to turn off the panel power, and then switch the main power switch to the off position. 1 Remove the roller cover from the bypass tray.
REPLACING SUPPLIES AND MAINTENANCE To clean the rollers, wipe the roller with a clean cloth. 3 Caution When cleaning the rollers, be careful not to injure your hands. Do not touch the surface of the roller if your hands are dirty. If the dirt is difficult to remove, moisten the cloth with a small amount of water or neutral detergent, and then wipe with a clean, dry cloth until no moisture remains. Attach the roller cover on the bypass tray. (1) Tilt the front of the cover slightly to attach it.
REPLACING SUPPLIES AND MAINTENANCE Turn on the power. Switch the main power switch "ON" and press the [POWER] key ( operation panel to turn on the operation panel power.
REPLACING SUPPLIES AND MAINTENANCE Cleaning the automatic document feeder rollers If you find that originals fed through the automatic document feeder misfeed or are soiled by the rollers, remove the rollers and clean them. If misfeeds or soiling continue to occur, replace the rollers. Before starting, remove any originals from the automatic document feeder. Press the [POWER] key ( ) on the operation panel to turn off the panel power, and then switch the main power switch to the off position.
REPLACING SUPPLIES AND MAINTENANCE To clean the rollers, wipe each roller with a clean cloth. 3 Caution When cleaning the rollers, be careful not to injure your hands. Do not touch the surface of the roller if your hands are dirty. If the dirt is difficult to remove, moisten the cloth with water or a neutral detergent. After wiping, wipe the roller dry with a clean cloth. Close the document conveyor cover on the automatic document feeder.
REPLACING SUPPLIES AND MAINTENANCE Turn on the power. Switch the main power switch "ON" and press the [POWER] key ( operation panel to turn on the operation panel power. ) on the 5 After turning on the power, make sure that an error message regarding replacement of the roller does not appear.
REPLACING SUPPLIES AND MAINTENANCE Cleaning the laser unit When the laser unit inside the machine becomes dirty, line patterns (coloured lines) may form in the printed image. Follow the steps below to clean the laser unit. Identifying lines (coloured lines) caused by a dirty laser unit • Coloured lines always appear in the same place. (The lines are never black.) • The coloured lines are parallel to the direction of paper feeding.
REPLACING SUPPLIES AND MAINTENANCE Open the front cover and remove the toner collection container. ☞ Replacing the toner collection container (page 16) 2 Remove the cleaning tool for the writing unit from the front cover.
REPLACING SUPPLIES AND MAINTENANCE Make sure that the cleaner at the tip of the cleaning tool is not dirty. 4 Cleaner If the cleaner is dirty, remove the cleaner and replace it with a clean one. For the procedure for replacing the cleaner, see steps 5 through 7. If the cleaner is not dirty, go to step 8. Pull out the replacement cleaner from the toner collection container.
REPLACING SUPPLIES AND MAINTENANCE Remove the dirty cleaner. Firmly grasp the tool close to where the cleaner is attached. Use your other hand to press down on the hook that secures the cleaner and remove the cleaner. 6 Return the removed cleaner to the toner collection container. Attach the new cleaner to the cleaning tool. Firmly grasp the tool close to where the cleaner is attached. Use your other hand to press down on the hook that secures the cleaner and remove the cleaner.
REPLACING SUPPLIES AND MAINTENANCE Clean the laser unit. (1) Point the cleaner down and slowly insert the tool into the hole that you wish to clean. The parts of the writing unit that require cleaning are indicated by labels similar to (A). (A) (2) Insert the cleaning tool all the way into the hole and then pull it back out. 8 Pull the cleaning tool out until you feel the tip of the tool leave the cleaning surface of the laser unit.
REPLACING SUPPLIES AND MAINTENANCE Repeat step 8 to clean all holes in the laser unit. 9 Holes to be cleaned There are a total of 4 holes to be cleaned in the laser unit. If the cleaner becomes dirty during cleaning, replace with a new cleaner. For the procedure for replacing the cleaner, see steps 5 to 7. Replace the cleaning tool. 10 Install the toner collection container.
REPLACING SUPPLIES AND MAINTENANCE Close the front cover. 12 Take care that your fingers are not pinched when closing the cover. Turn on the power. Switch the main power switch "ON" and press the [POWER] key ( operation panel to turn on the operation panel power.
REPLACING SUPPLIES AND MAINTENANCE Cleaning the PT charger of the primary transfer belt unit If black or coloured lines still remain after the document glass / automatic document feeder and main charger have been cleaned, use the PT charger cleaner to clean the PT charger. Press the [POWER] key ( ) on the operation panel to turn off the panel power, and then switch the main power switch to the off position. 1 Open the front cover and remove the toner collection container.
REPLACING SUPPLIES AND MAINTENANCE Clean the PT charger. (1) Slowly pull the PT charger cleaner out until you feel a slight resistance. 3 (2) Slowly push the PT charger cleaner back in. (3) Repeat the above (1) to (2) three times. Install the toner collection container.
REPLACING SUPPLIES AND MAINTENANCE Close the front cover. 5 Take care that your fingers are not pinched when closing the cover. Turn on the power. Switch the main power switch "ON" and press the [POWER] key ( operation panel to turn on the operation panel power.
SPECIFICATIONS Machine specifications / copier specifications Name Digital Full Colour Multifunctional System MX-C310/MX-C311/MX-C380/MX-C381/MX-C400 Type Desktop Display MX-C310/MX-C380/MX-C400: 4.3 inch colour LCD MX-C311/MX-C381: 8.
SPECIFICATIONS Machine specifications / copier specifications (Continued) Warm-up time 90 seconds or less (This may vary depending on the ambient conditions.) First-copy time Colour copy time:8.9 seconds or less Black and white copy time: 8.0 seconds or less (This may vary depending on the status of the machine.) Copy ratios Variable: 50% to 200% in increments of 1%, total 151 increments Fixed presets: 50%, 70%, 81%, 86%, 100%, 115%, 122%, 141% and 200% for AB sizes.
SPECIFICATIONS Machine specifications / copier specifications (Continued) Paper sizes: A4, B5, A5, 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 7-1/4" x 10-1/2", 5-1/2" x 8-1/2", envelopes, 16K (Includes automatic paper size detection function. Paper sizes from 100 mm x 148 mm (3-15/16" x 5-53/64") to 216 mm x 356 mm (8-33/64" x 14-1/64") can be entered.) Bypass tray Paper weights: Thin paper (55 g/m2 to 59 g/m2 (15 lbs. to 16 lbs.
SPECIFICATIONS Machine specifications / copier specifications (Continued) Interface port LAN connectivity: 10Base-T / 100Base-TX / 1000Base-T USB connectivity: Type A connector supports USB 2.0 (Hi speed)* Compatibility requirements of USB 2.0 Memory Capacity: Max. 32 GB Disk Format: FAT32 only Type B connector supports USB 2.0 (Hi speed) Required power supply Local voltage ±10% (For the power supply requirements, see the name plate in the lower corner of the left side of the machine.
SPECIFICATIONS Continuous copying speeds* MX-C310/ MX-C311 Model Copy ratio MX-C380/ MX-C381 MX-C400 100% / Reduced / Enlarged Copy mode Colour B/W Colour B/W Colour B/W A4 31 copies/ min. 31 copies/ min. 38 copies/ min. 38 copies/ min. 38 copies/ min. 38 copies/ min. B5, 8-1/2" x 11", 7-1/4" x 10-1/2", 16K 31 copies/ min. 31 copies/ min. 40 copies/ min. 40 copies/ min. 40 copies/ min. 40 copies/ min.
SPECIFICATIONS Acoustic noise emission (measurement according to ISO7779) MX-C310/ MX-C311 MX-C380/ MX-C381 MX-C400 Colour : 6.9 B Printing mode (continuous printing) B/W : 6.9 B Colour : 7.0 B B/W : 7.1 B Colour : 7.0 B B/W : 7.1 B Standby mode 5.3 B 5.3 B Model Sound power level LwA 5.
SPECIFICATIONS Automatic document feeder specifications Original sizes A4 to A5, 8-1/2" x 14" to 5-1/2" x 8-1/2", long paper (max. width 216 mm (8-1/2") x max. length 500 mm* (19-5/8"), scanning in mono 2 mode of one side only is possible in fax and image scan modes) Original weight One-sided 35 g/m2 to 128 g/m2 (9 lbs. to 32 lbs.) (Paper weights from 35 g/m2 (9 lbs.) to 49 g/m2 (13 lbs.) require the use of slow scan mode.) Two-sided 50 g/m2 to 105 g/m2 (13 lbs. to 28 lbs.
SPECIFICATIONS Business card feeder specifications Model Business card* MX-BTX1 Sizes 51 mm x 89 mm to 55 mm x 91 mm (2-1/64" x 3-33/64" to 2-11/64" x 3-19/32") Thickness 0.1 mm to 0.2 mm (0.004" to 0.008") Scanning Single-sided (face-up) Capacity Stack height 3.5 mm (9/64") maximum Dimensions 115 mm (W) x 88 mm (D) x 25 mm (H) (4-17/32" (W) x 3-15/32" (D) x 63/64" (H)) Weight Approx. 40 g (0.09 lbs.
SPECIFICATIONS 500-sheet paper feed unit specifications Model MX-CSX1 (tray 2) Paper sizes A4, B5, A5*, 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 7-1/4" x 10-1/2", 5-1/2" x 8-1/2"*, 16K Paper weight Plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.)) Paper capacity 500 sheets (80 g/m2 (21 lbs.
SPECIFICATIONS Finisher specifications Model MX-FN12 Paper sizes A4, B5, A5, 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 7-1/4" x 10-1/2", 5-1/2" x 8-1/2", envelopes, 16K Paper weight Thin paper (55 g/m2 to 59 g/m2 (15 lbs. to 16 lbs.)) plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.)) heavy paper (106 g/m2 to 209 g/m2 (28 lbs. bond to 110 lbs.
SPECIFICATIONS Finisher specifications (Continued) Maximum number of sheets for stapling*3 30 sheets *1 The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of paper, and the storage conditions of the paper. *2 Up to 20 envelopes can be output. *3 The maximum number of sheets for stapling assumes a paper weight of 90 g/m2 (24 lbs.) and includes two cover sheets of 106 g/m2 to 209 g/m2 (28 lbs. bond to 110 lbs. index).
SPECIFICATIONS Printer specifications Type Built-in Continuous printing speed Same as continuous copying speed (When printing same document continuously on A4 (8-1/2" x 11") plain paper in non-offset mode, excluding processing time.) Printing resolution 600 x 600 dpi / 1200 x 1200 dpi Printer driver type PCL5c, PCL6, PostScript 3 compatible*1, XPS*2 Supported protocols TCP/IP, IPX/SPX, NetBEUI, EtherTalk Supported client See "VERIFYING SYSTEM REQUIREMENTS" in the Software Setup Guide.
SPECIFICATIONS Network scanner / Internet Fax*1 specifications Type Built-in Scanning resolution (dpi) 100 x 100, 200 x 200, 300 x 300, 400 x 400, 600 x 600 Internet Fax: 200 x 100, 200 x 200, 200 x 400, 400 x 400, 600 x 600 (200 x 100, 200 x 200 when file type is TIFF-S) Halftone can be selected for resolutions other than 200 x 100 dpi. Color (200 x 200 dpi) One-sided : 35 pages/min. (8-1/2" x 11"), 33 pages/min. (A4) Two-sided : 12 pages/min.
SPECIFICATIONS Pull scan function (TWAIN) specifications Supported protocol TCP/IP (IPv4) Supported client Windows 98 / Me / 2000 / XP / Server 2003 / Vista / Server 2008 PC operating systems Colour modes Full Colour, Greyscale, Mono Diffusion, Mono 2 gradation Resolution settings 75 dpi, 100 dpi, 150 dpi, 200 dpi, 300 dpi, 400 dpi, 600 dpi (The resolution can be specified by entering a numerical value from 50 to 9600 dpi.
SPECIFICATIONS Facsimile specifications Model MX-FXX3 Applicable telephone line Public switched telephone network, PBX Scanning resolution (supports ITU-T standards) 8 x 3.85 lines/mm (Standard), 8 x 7.7 lines/mm (Fine, Fine-Halftone), 8 x 15.4 lines/mm (Super Fine, Super Fine Halftone), 16 x 15.4 lines/mm (Ultra Fine, Ultra Fine - Halftone) Transmission speed 33.6 kbps down to 2.
SPECIFICATIONS Facsimile specifications (Contimued) Remarks Extension telephone connection Possible (1 telephone) Number of one-touch keys for storing destinations*2 Maximum number of keys: 999 Number of destinations that can be stored in a group (1 key)*2 Maximum number of destinations in one group (1 key): 500 Timer transmission Yes Program function Yes (48 programs) F-code transmission Supported (SUB/SEP (sub-address) and SID/PWD (passcode) signals can be transmitted / received) Image memo
INFORMATION ON DISPOSAL A. Information on Disposal for Users (private households) 1. In the European Union Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin! Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment.
✂ Contact at: Administrator Name: Information that the administrator of the machine requires is printed on the back of this page. (Separate this page from the manual and keep it in a safe place. In addition, fill in the name of the administrator and the administrator's contact information in the left hand margin.
TO THE ADMINISTRATOR OF THE MACHINE (Separate this page from the manual and keep it in a safe place.) Factory default passwords When accessing the system settings, the administrator password is required to log in with administrator rights. The system settings can be configured in the Web pages as well as on the operation panel. To access the system settings using the Web pages, a password is also required.
TO THE ADMINISTRATOR OF THE MACHINE For the users of the fax function Important safety instructions • If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone network. • The AC power outlet shall be installed near the equipment and shall be easily accessible. • Never install telephone wiring during a lightning storm.
TO THE ADMINISTRATOR OF THE MACHINE Trademark acknowledgments The following trademarks and registered trademarks are used in conjunction with the machine and its peripheral devices and accessories. • Microsoft®, Windows®, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000, Windows® XP, Windows Server® 2003, Windows Vista®, Windows Server® 2008 and Internet Explorer® are registered trademarks or trademarks of Microsoft Corporation in the U.S.A. and other countries.
SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg
MX-C310/MX-C311/MX-C380/MX-C381/MX-C400 Maintenance & Safety Guide PRINTED IN FRANCE TINSE4108GHZ2
