INSTRUCTION MANUAL
Note for Users in U K IMPORTANT The wires in the mains lead of this apparatus are coloured in accordance with the following code: BLUE: BROWN: Neutral Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: * The wire which is coloured B LU E must be connected to the terminal which is marked with the letter N or coloured BLACK.
INTRODUCTION Thank you for purchasing the SHARP Floppy Disk MZ-80FB/FBK. It is a peripheral for use with the SHARP Personal Computer MZ-80B which can operate a maximum of 4 drives. We believe that it will be very useful as an external memory unit because of its large capacity and high speed access. Read this instruction manual carefully before using the Floppy Disk so you can use it correctly. Page • • • • • • • • Floppy Disk MZ-80FB ......................................
Floppy Disk MZ-80FB L Disk Drive Comes with 2 drives (upper, lower). 4 ...... 5."- - -ill 2~ SHARP - --, -r---- ~ 2 3 [J] I @ I I 3 4 I~ -, 6 5 6 7 IN = = = = = = = = = = = = == 7 S S -II----=~-- Appliance Inlet Connect the supplied power cord here. 10 FG Terminal Connect the supplied braided wire to this terminal. 11 Rating Name Plate Use a power supply with the voltage shown here.
I nsert the I/O card MZ-80F I into the lowest connector (No. 6) on the right-hand side of the extension unit on the back of the MZ-80B. The Fig. on the left shows a I/O card inserted. Refer to the instruction manual for the MZ80B for the correct method of inserting the card and then do it properly. First remove the screws and then insert the card. Finally replace the screws. (Back of MZ-80B) I I/O Card 2 Connect the connector of signal cable MZ-80FC to the signal terminal of the I/O card.
CD Disk Drive Comes with 2 drives (upper, lower). - SHARP t-fj] J) t-:l) - ---- r-
Remove the signal cable connected to the MZ-80FB signal terminal. However, if connected to the I/O side, leave it as it is. Signal Cable MZ-80FC (Back of MZ-80FB) = Signal Cable MZ-80FC IN OUT liB'" of MZ-BOFBKI 2 Connect the signal cable that was removed as explained above to the left-side signal terminal indicated by "IN" on the back of the MZ-80FBK. Besides, firmly fix both sides of the connector with the screws to fasten it. This method is the same as that on page 3, section (2) and (3).
r--133.3mm rD -----j Write-protection ,.notch E E Center hole M M Index hole 1 Diskette This unit uses a 5.25" mini-disk that records on both sides as the recording medium. Its external appearance is as shown on the left. It's called a diskette and is a magnetic sheet covered by a jacket. ~ ... l 0 Head window 2 Inserting a Diskette 1. Put a finger on the bottom of the front door and lightly pull this door toward you to open it. 2.
Do not touch, soil or scratch the recording surface (Head YVindow) of the diskette with your finger. This may cause improper operation or result in no operation. Do not bend or fold the diskette or it will become unusable. Do not bring magnetic things near the diskette or the contents of the diskette will be destroyed. In addition, it's dangerous to bring a diskette near machines (motors, etc.) that generate a magnetic field.
Cautions (A) Installation 1. Do not install the unit in the following places. Damp places. In direct sunlight. Dusty places. Places where the temperature is very high or low. Places that vibrate. 2. Install the unit on a solid, level stand. 3. Use a power supply voltage as indicated on the rating name plate on the back of the unit. 4. Do not install the unit near machines that generate a lot of noise. Also use a separate power source for these kinds of machines.
Specifications No. of drives: Connection between drives: Recording medium: Recording: No. of tracks: Sector: Formatted capacity: Power source: Power consumption: Operating conditions: External dimensions: Weight: Accessories: Options: Dual drives/unit Da isy-cha i n system 5.25" both-sides flexible disk Both sides, double density 70 tracks Soft sectored 280 K byte/sheet (at 16 sectors/track) Local supply voltage (Use power supply voltage as shown on rating name plate).
: SHARP CORPORATION TI NSE0016PAZZ 801205-1000-K Pri nted in Japan MZ-80FB/FBK E1