Installation Manual

ManualsBrandsSharp ManualsProjectorsPG-F267X

MODEL AN-STWM20

INSTALLATION INSTRUCTIONS FOR SHORT THROW PROJECTOR

WALL MOUNTING BRACKET FOR USE WITH SHARP PROJECTOR

MODEL NOS. PG-F267X, PG-D2870W

AVDEX CORPORATION

115 HENRY STREET, FREEPORT, NY 11520

TEL: 516-546-2272 FAX: 516-623-7766 TOLL FREE: 1-800-866-1820

E-MAIL: SECURITY@AVDEX.COM

AN-STWM20 SHORT THROW

WALL MOUNTING BRACKET

WITH EXTENSION

COLOR: WHITE

Summary of content (8 pages)

PAGE 1
MODEL AN-STWM20 INSTALLATION INSTRUCTIONS FOR SHORT THROW PROJECTOR WALL MOUNTING BRACKET FOR USE WITH SHARP PROJECTOR MODEL NOS. PG-F267X, PG-D2870W AN-STWM20 SHORT THROW WALL MOUNTING BRACKET WITH EXTENSION COLOR: WHITE AVDEX CORPORATION 115 HENRY STREET, FREEPORT, NY 11520 TEL: 516-546-2272 FAX: 516-623-7766 TOLL FREE: 1-800-866-1820 E-MAIL: SECURITY@AVDEX.
PAGE 2
SHORT THROW PROJECTOR WALL MOUNTING BRACKET AN-STWM20 INSTALLATION INSTRUCTIONS C A U T I O N INSTALLATION OF THIS ADJUSTABLE WALL MOUNTING BRACKET SHOULD BE PERFORMED BY QUALIFIED SERVICE/ INSTALLATION PERSONNEL FOLLOWING THE INSTALLATION INSTRUCTIONS INCLUDED WITH THIS BRACKET THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
PAGE 3
SHORT THROW PROJECTOR WALL MOUNTING BRACKET AN-STWM20 INSTALLATION INSTRUCTIONS FIGURE 1. ILLUSTRATION OF PARTS FOR WALL MOUNTING BRACKET A. B. C. D. F. G. H. I. E. D. L. J K. M N. INVERT THE PROJECTOR IMAGE Please refer to the owners manual for your LCD Projector for detailed instructions of how to electrically invert the projected image to accommodate its use in the wall mounted mode.
PAGE 4
SHORT THROW PROJECTOR WALL MOUNTING BRACKET AN-STWM20 INSTALLATION INSTRUCTIONS STEP 1. ATTACH THE MOUNTING ASSEMBLY TO THE BOTTOM OF THE PROJECTOR. 1.1 Place the flat surface of the 4 1/4” x 5 3/8” plate against the bottom of the Projector with the “U” shaped cut out toward the rear of the projector. See Fig. 2 1.2 Align the plate so that the four crescent shaped mounting slots are over the threaded holes in the bottom of the projector. 1.3 Install the four M4x10 mounting Screws and washers.
PAGE 5
SHORT THROW PROJECTOR WALL MOUNTING BRACKET AN-STWM20 INSTALLATION INSTRUCTIONS FIG. 3 WALL MOUNTING PLATE MOUNT ONTO WALL USING HEX HEAD BOLTS PROVIDED CABLE MANAGEMENT ACCESS 2.2 Note that the mounting plate has a rectangular hole intended to facilitate wire and cable management if the wiring is fed through the wall. 2.3 Attach the upper support bar to the wall mounting bracket. FIG.
PAGE 6
SHORT THROW PROJECTOR WALL MOUNTING BRACKET AN-STWM20 INSTALLATION INSTRUCTIONS 2.5 Tighten the button head screws on both sides of the extension tube after you have set the desired length. See Figure 5. STEP 3. HANG THE PROJECTOR 3.1 Hang the projector on the long inner slide tube by sliding the rectangular sleeve over the long tube. 3.2 Slide the sleeve forward over the long tube to the desired position and secure it with the two knobs on either side of the sleeve. 3.
PAGE 7
SHORT THROW PROJECTOR WALL MOUNTING BRACKET AN-STWM20 INSTALLATION INSTRUCTIONS SHORT THROW PROJECTOR WALL MOUNTING BRACKET WITH PROJECTOR MOUNT ASSEMBLY SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE A. B. C. D. E. F.
PAGE 8
ONE YEAR LIMITED WARRANTY AVDEX Corporation warrants to the first end use purchaser, that this AVDEX brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective product or part thereof at no charge to the purchaser for parts or for labor, excluding costs of removal and/or installation, for one year from date of purchase.