Instructions / Assembly

ManualsBrandsSharp ManualsAppliance parts27 in. Trim Kit for Sharp SMC1842CS and SMC1843CM Microwave Ovens in Stainless Steel

For Sharp Carousel

Built-in Kit

Models RK49S27 or RK49S30

S = STAINLESS

THIS KIT IS UL APPROVED TO ALLOW CERTAIN MICROWAVE

OVENS TO BE INSTALLED ABOVE ANY ELECTRIC WALL OVEN.

PLEASE SEE THE OPERATION MANUAL REGARDING APPROVED

BUILT-IN APPLICATIONS.

IMPORTANT:

This Built-in Kit is designed for and approved only for those

Sharp Microwave Ovens specifying Built-In Kit RK49S27 or

RK49S30. Refer to instruction manual for approved models.

PLEASE READ THESE INSTRUCTIONS

THOROUGHLY

BEFORE BEGINNING INSTALLATION!

• Be sure to DISCONNECT THE PLUG of the microwave

oven from the electrical outlet before installing the Built-in

Kit. Remove the Carousel turntable from the oven cavity.

• Because the kit includes metal parts, due caution should

be used in handling and installation to avoid the possibil-

ity of injury.

ITEM PART NAME QTY

A FRONT FRAME

RK49S27: FDECAB233MRK0

RK49S30: FDECAB235MRK0

B BACK FRAME

RK49S27: FDECAB234MRK0

RK49S30: FDECAB236MRK0

C EXHAUST DUCT ASSEMBLY

PDUC-B194MRP0

D SCREW D: XTSS740P20000 2

E SCREW E: XOPS740P16000 4

INSTALLATION INSTRUCTIONS

A B

V-cut

indicates

center of

duct

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS For Sharp Carousel® Built-in Kit Models RK49S27 or RK49S30 S = STAINLESS THIS KIT IS UL APPROVED TO ALLOW CERTAIN MICROWAVE OVENS TO BE INSTALLED ABOVE ANY ELECTRIC WALL OVEN. PLEASE SEE THE OPERATION MANUAL REGARDING APPROVED BUILT-IN APPLICATIONS. IMPORTANT: This Built-in Kit is designed for and approved only for those Sharp Microwave Ovens specifying Built-In Kit RK49S27 or RK49S30. Refer to instruction manual for approved models.
PAGE 2
STEP 1 CABINET OR WALL OPENING NOTES The opening in the wall or cabinet must be within the following dimensions: Cut Out RK49S27 RK49S30 Height (A) 14 1/2" to 15 3/4" 14 1/2" to 15 3/4" Width (B) 24 11/16" to 25 5/16" 24 13/16" to 26 3/4" Minimum Depth (C) 20" 20" • Please allow minimum 3" wood gap between the microwave oven cutout and the appliance cutout below the microwave oven. See Sketch 2 Outlet should NOT be in the shaded area as indicated on Sketch 1. Microwave cutout 4" 3" Min.
PAGE 3
STEP 2 EXHAUST DUCT ASSEMBLY INSTALLATION 1. Place the EXHAUST DUCT ASSEMBLY in the center of the opening. Align the front edge of the duct with the front of the cabinet. 2. Secure the EXHAUST DUCT ASSEMBLY with two SCREWS D. See Sketch 3. Screw D Screw D CL Exhaust duct assembly, align to front edge of cabinet SKETCH 3 STEP 3 FRAME INSTALLATION 1. Place the oven adjacent to the wall or cabinet opening. Plug the POWER CORD into the electrical outlet. 2.
PAGE 4
STEP 3 FRAME INSTALLATION 3. BACK FRAME INSTALLATION: Position back frame equal space top to bottom, side to side. Mark for 4 holes, center punch and pre-drill with 1/16" drill bit. Secure frame with 4 SCREWS (E). See Sketch 6. Mounting holes Mounting holes Screw E Screw E Snap Attachment Equal gap side to side Equal gap top, bottom Screw E Screw E Mounting holes Mounting holes SKETCH 6 4. FRONT FRAME INSTALLATION: Place the FRONT FRAME onto the BACK FRAME and align ball studs and receivers.