OPERATION MANUAL & INSTALLATION INSTRUCTIONS MODELS : SHC2432FS / SHC3042FS / SHC3062FS / SHC3662FS CUSTOMER ASSISTANCE........................................ 2 MEASURE THE INSTALLATION................................... 8 CONSUMER LIMITED WARRANTY............................... 3 INSTALLATION INSTRUCTIONS.................................. 9 BEFORE INSTALLING THE RANGE HOOD........................ 4 OPERATIONS.................................................... 15 RANGE HOOD DIMENSIONS.............
CUSTOMER ASSISTANCE UNITED STATES ONLY REGISTER YOUR PRODUCT Registering your new product is easy and offers benefits that help you get the most out of your Sharp product including: 9 Convenience: If you ever need warranty support, your product information is already on file. 9 Communication: Stay up to date with important notifications and special offers from SHARP. 9 Support: Quickly access support content including Owner’s Manuals, FAQ’s, How-to Videos, and much more.
CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
BEFORE INSTALLING THE RANGE HOOD 2 NEVER PICK UP A FLAMING PAN – You may be burned. READ AND SAVE THESE INSTRUCTIONS TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSON(S) OBSERVE THE FOLLOWING: 3 DO NOT USE WATER, including wet dishcloths or towels – This could cause a violent steam explosion. 1 Use this unit only in the manner intended by the manufacturer.
RANGE HOOD DIMENSIONS 6-25 / 3 2〞 9-21/32〞 1-3/8〞 Min.25-3/8〞 Max.
RANGE HOOD MAIN PARTS PARTS INCLUDED Unpack hood and check contents. You should receive: FOR MODEL: SHC2432FS QTY. FOR MODELS: SHC3062FS, SHC3662FS, SHC3042FS PRODUCT COMPONENTS 1 Hood 1 Damper / Duct Connector 1 Upper Flue Mounting Bracket 1 Aluminum Grease Filters 1 Parts Bag containing: 3 Mounting Screws (no. 8 x 11/2" Flat Head) 1 Washers 7 1 1 1 1 2 1 1 10 7 7 2 QTY.
PRODUCT SPECIFICATIONS MODEL ITEM SHC2432FS SHC3042FS SHC3062FS SHC3662FS 120 Volts 2.0 Amps 60Hz 120 Volts 2.7 Amps 60Hz 120 Volts 3.7 Amps 60Hz 120 Volts 3.7 Amps 60Hz Width 23-9/16" 29-1/2" 29-1/2" 35-1/4" Height 25-3/8" to 40-3/8" 25-3/8" to 40-3/8" 25-3/8" to 40-3/8" 25-3/8" to 40-3/8" Depth 19-11/16" 19-11/16" 19-11/16" 19-11/16" Power Requirements Case Dimensions Lamps (2 levels) 2 LED bulbs: 5.
MEASURE THE INSTALLATION The minimum hood distance above cooktop MUST NOT BE LESS than 26". A maximum of 36" above cooktop is highly recommended for best capture of cooking impurities. Distances over 36" are at the installer and users discretion; providing that the ceiling height permits.
INSTALLATION INSTRUCTIONS DAMPER/ADAPTER PREPARATION FOR SHC2432FS: INSTALL THE DUCTWORK (DUCTED HOODS ONLY) Damper is packed in side carton separately. Use four Mounting Screws (no. 8 x 3/8" Pan Head) to fix the damper as shown in the picture below. 1 Decide where the ductwork will run between the hood and the outside. Damper ROOF CAP 6" ROUND DUCT DECORATIVE FLUE HOOD WALL CAP ROUND ELBOW 26" MIN.
MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS • INSTALLATION INSTRUCTIONS BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS INSTALL THE HOOD MOUNTING BRACKET Page 5 INSTALL THE HOOD MOUNTING BRACKET WALL STUDS FRAMING BEHIND DRYWALL C L 19⁄16” 77⁄8” 315⁄16” NOTE: MOUNTING BRACKET LOCATION (ABOVE 36” HIGH COOKTOP) On 8-ft.
INSTALLATION INSTRUCTIONS 5 To make sure there will be adequate clearance between top INSTALL UPPER FLUE MOUNTING BRACKET of hood and lower flue mounting bracket for ductwork: Elbow must be located below lower flue mounting bracket. 1 If a framing member is not present, drill two 5/16" diameter 6 Align the hood and center it above the hood mounting holes where shown. Insert drywall anchors into the holes. bracket. Gently lower the hood until it securely engages the bracket.
INSTALLATION INSTRUCTIONS 10 Plug hood power cord into the outlet. INSTALL THE HOOD (VERTICALLY DUCTED HOODS ONLY) 1 DO NOT REMOVE the protective plastic film covering the LOWER FLUE MOUNTING BRACKET decorative flue and the hood at this time. 2 Lay the back side of the hood flat on a table. Use a piece of cardboard to avoid damaging the table or the hood. 3 Remove the grease filters by pulling down the metal latch LOWER FLUE tab and tilting filters downward to remove.
INSTALLATION INSTRUCTIONS 10 Use duct tape to make all joints secure and air tight. INSTALL THE HOOD (NON-DUCTED HOODS ONLY) INSIDE BACK OF HOOD Non-ducted installation requires a Non-Duct kit for your model which is separately sold. MOTOR / BLOWER ASSEMBLY AVAILABLE ACCESSORY PARTS NUMBERS RANGE HOOD SIDE VIEW NON-DUCT KIT CHARCOAL FILTERS EXTENSION FLUE SHC2432FS SKCH32DLK SKCH32CFL HOLES LOCATION SHC3042FS Ø 5/16" TYP.
INSTALLATION INSTRUCTIONS LOWER FLUE MOUNTING BRACKET INSTALLATION OF SKCH32CFL FOR SHC2432FS Close Close LOWER FLUE Open 8 Remove the upper flue from inside the lower flue. Install Open INSTALLATION OF SKCH62CFL FOR SHC3042FS/SHC3062FS/SHC3662FS the lower flue bracket HD1179 to the lower flue using (2) flue bracket screws (no. 8 x 3/8"). Make sure that the bracket is positioned inside of the lower flue flanges - with the slots on top. Carefully replace the upper flue inside the lower flue.
OPERATIONS CONTROL PANEL LED DISPLAY BLOWER CONTROLS LIGHT ON/OFF LED DISPLAY 15 MINUTE DELAY POWER ON/OFF CAP (CFM ADJUSTABLE PLATFORM) SETTING (SHC3062FS & SHC3662FS ONLY) • It indicates the blower power level by number. In case the blower power (CFM = Cubic Feet per Minute) shall be limited due to state or local “Makeup Air” regulations, the CFM can be adjusted to a lower level to comply with the regulations.
CLEANING & MAINTENANCE Proper maintenance of the Range Hood will assure proper performance of the unit. STAINLESS STEEL CLEANING MOTOR • Regularly wash with clean cloth or rag soaked with warm water and mild soap or liquid dish detergent. DO: The motor is permanently lubricated and never needs oiling. If the motor bearings make excessive or unusual noise, replace the blower with the exact service blower. • Always clean in the direction of original polish lines.
TROUBLE SHOOTING FAULT Light on, but motor does not work POSSIBLE CAUSE SOLUTION • Fan switch turned off • Select a fan switch position • Fan switch failed • Contact service center • Motor failed • Contact service center • House fuses blown • Reset/Replace fuses • Mains power cable is loose or disconnected • Refit mains power cable to power outlet • One way valve and the outlet are not tightly sealed • Take down the one way valve and seal with sealant • Leakage from the connection of chimney
SHARP ELECTRONICS CORPORATION • 100 Paragon Drive • Montvale, New Jersey 07645 • USA
