Service manual

ManualsBrandsSharp ManualsAll in One PrinterUX-A1000

UX-A1000U

No. 00ZUA1000USME

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for

maintaining the safety and performance of the set.

This document has been published to be used

for after sales service only.

The contents are subject to change without notice.

SHARP CORPORATION

SERVICE MANUAL

FACSIMILE

UX-A1000

MODEL SELECTION CODE DESTINATION

UX-A1000 U

U.S.A.

MODEL

CHAPTER 1. GENERAL DESCRIPTION

[1] Specifications ............................................ 1-1

[2] Operation panel......................................... 1-2

[3] Transmittable documents .......................... 1-3

[4] Installation ................................................. 1-4

[5] Quick setup guide ..................................... 1-9

[6] Quick reference guide ..............................1-10

CHAPTER 2. ADJUSTMENTS

[1] Adjustments............................................... 2-1

[2] Diagnostics and service soft switch .......... 2-3

[3] Troubleshooting....................................... 2-25

[4] Error code table....................................... 2-26

CHAPTER 3. MECHANISM BLOCKS

[1] General description .................................. 3-1

[2] Ink jet printer ............................................ 3-3

[3] Disassembly and assembly

procedures ....................................... 3-6

CHAPTER 4. DIAGRAMS

[1] Block diagram ............................................4-1

[2] Wiring diagram .......................................... 4-2

[3] Point-to-point diagram ............................... 4-3

CHAPTER 5. CIRCUIT DESCRIPTION

[1] Circuit description...................................... 5-1

[2] Circuit description of control PWB..............5-2

[3] Circuit description of TEL/LIU PWB ........ 5-13

[4] Circuit description of printer PWB ............5-15

[5] Circuit description of

power supply PWB ............................5-18

[6] Circuit description of CIS unit ...................5-18

CHAPTER 6. CIRCUIT SCHEMATICS AND

PARTS LAYOUT

[1] Control PWB circuit ................................... 6-1

[2] TEL/LIU PWB circuit ............................... 6-10

[3] Printer PWB circuit ...................................6-14

[4] Power supply PWB circuit ...................... 6-20

[5] Operation panel PWB circuit ................... 6-22

[6] Ink PWB circuit ........................................ 6-24

CHAPTER 7. OPERATION FLOWCHART

[1] Protocol ..................................................... 7-1

[2] Power on sequence .................................. 7-2

CHAPTER 8. OTHERS

[1] Service tools.............................................. 8-1

[2] Changing the record paper size ................ 8-6

[3] Rewriting version up the FLASH ROM

Refer to the Service Manual of UX-B700U

PARTS GUIDE

CONTENTS

Summary of content (128 pages)

PAGE 1
UX-A1000U SERVICE MANUAL No. 00ZUA1000USME FACSIMILE MODEL MODEL UX-A1000 UX-A1000 SELECTION CODE DESTINATION U U.S.A. CONTENTS CHAPTER 1. GENERAL DESCRIPTION [1] Specifications ............................................ 1-1 [2] Operation panel ......................................... 1-2 [3] Transmittable documents .......................... 1-3 [4] Installation ................................................. 1-4 [5] Quick setup guide .....................................
PAGE 2
UX-A1000U CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer’s instructions.
PAGE 3
UX-A1000U CHAPTER 1. GENERAL DESCRIPTION [1] Specifications Automatic dialing Compression scheme MR, MH, MMR Rapid Key Dialing: 18 numbers Speed Dialing: 81 numbers Compatibility ITU-T (CCITT) G3 mode Input document size Automatic feeding: Width: 5.8 to 8.5" (148 to 216 mm) Length (20 pages): 5.5 to 11" (140 to 279 mm) Length (5 pages): 5.5 to 14" (140 to 356 mm) Manual feeding: Width: 5.8 to 8.5" (148 to 216 mm) Length: 5.5 to 23.
PAGE 4
UX-A1000U [2] Operation panel 1 3 2 4 6 5 PLAIN PAPER INKJET FAX TEL REC/MEMO GHI 05 06 TAD 07 08 09 10 11 12 13 14 15 17/G1 18/G2 3 5 FUNCTION SKIP COPY/HELP SPEED DIAL 9 0 REPEAT UP 6 8 16/POLL RESOLUTION/ RECEPTION MODE WXYZ TUV 7 04 MNO JKL PQRS 03 DEF 2 4 02 PLAY ABC 1 FAX 01 Z START/ MEMORY A REDIAL HOLD DOWN SPEAKER STOP DELETE PANEL RELEASE 7 8 9 10 11 12 13 14 15 16 17 18 1 Display This displays messages and prompts to help you
PAGE 5
UX-A1000U [3] Transmittable documents 5. Automatic Document Feeder Capacity 1. Document Sizes Number of pages that can be placed into the feeder at anytime is as follows: Normal size width length Normal size: max. ADF 20 pages 5.8" - 8.5" (148 – 216 mm) 5.5" - 11" (140 – 279 mm) Special size: Single sheet only (manual feeding) NOTES: (Max.) (Max.) Letter size (Min.
PAGE 6
UX-A1000U [4] Installation 2. Assembly and connections 1. Site selection 1 Connect the handset as shown and place it on the handset rest. The ends of the handset cord are identical, so they will go into either jack. Take the following points into consideration when selecting a site for this model. ENVIRONMENT • • The machine must be installed on a level surface. • Provide easy access to the front, back, and sides of the machine.
PAGE 7
UX-A1000U 3. Installing the Print Cartridge 3 Plug the power cord into a 120 V, 60 Hz, grounded AC (3-prong) outlet. • Caution! • Do not plug the power cord into any other kind of outlet. This will damage the machine and is not covered under the warranty. • Make sure you have removed all of the packing tape before plugging in the power cord. Plugging in the power cord without doing so may damage the machine.
PAGE 8
UX-A1000U 5 Insert the new print cartridge into the cartridge holder. 6 Place your index finger on the tab as shown and close the cartridge holder cover with your thumb. Make sure the cover clicks into place. 7 Close the print compartment cover. 12 In the alignment page that the machine prints, locate the line that comes closest to forming a completely straight line. In this example, "15" comes closest to forming a straight line.
PAGE 9
UX-A1000U 4. Loading printing paper 1 Setting the paper size You can load letter or legal size paper in the paper tray. Recommended paper weight is 20-lb. Copy Bond. The maximum number of sheets is as follows: 1 2 Letter size: Approx. 200 sheets (20-Ib. copier paper at room temperature; Legal size: maximum stack height should not exceed line on tray) Approx. 100 sheets (20-Ib. copier paper at room temperature) The fax has been set at the factory to scale received faxes to letter size paper.
PAGE 10
UX-A1000U 5. Clearing a jammed document 6. Clearing jammed printing paper If the original document doesn't feed properly during transmission or copying, or DOCUMENT JAMMED appears in the display, first try pressing the document doesn't feed out, remove it as explained below. START/ MEMORY 1 Open the operation panel. 2 Open the print compartment cover. . If Important: Do not try to remove a jammed document without releasing it as explained below. This may damage the feeder mechanism.
PAGE 11
UX-A1000U [5] Quick setup guide 1 3. Close the print compartment cover. 2. Remove the packing tape. 1. Press as shown and pull to open the print compartment cover. Note: To enter your name and fax number and set the data and time so that they appear at the top of each fax you send, see pages 26-29 of your operation manual. 2 3 Attach the trays. 1. Connect the handset. Pull the paper plate toward you and attach the paper tray cover. Paper plate 2. Connect the phone line cord to the TEL.
PAGE 12
UX-A1000U [6] Quick reference guide Sending Faxes Receiving Faxes Place your document (up to 20 pages) face down in the document feeder. RESOLUTION/ RECEPTION MODE Press until the arrow in the display points to the desired reception mode. TEL FAX JAN-03 10:30 TAD RESOLUTION/ RECEPTION MODE Normal Dialing TEL FAX JAN-03 10:30 TAD TEL FAX 1. Lift the handset or press SPEAKER . 2. Dial the fax number. 3. Wait for the reception tone (if a person answers, ask them to press their Start key). 4.
PAGE 13
UX-A1000U CHAPTER 2. ADJUSTMENTS [1] Adjustments General Since the following adjustments and settings are provided for this model, make adjustments and/or setup as necessary. 1. Adjustments of output voltage (FACTORY ONLY) 1. Install the power supply unit in the machine. 2. Set the recording paper and document. 3. When the document is loaded, power is supplied to the output lines. Confirm that outputs are within the limits below.
PAGE 14
UX-A1000U 2. IC protectors replacement 4. Volume adjustment ICPs (IC Protectors) are installed to protect the motor driver circuit. ICPs protect various ICs and electronic circuits from an overcurrent condition. You can adjust the volume of the speaker, handset, and ringer using the UP and DOWN keys. The location of ICPs are shown below: 1. Press the SPEAKER key. CNPW CNPRT CNPN FU101 FU1 (1) Speaker 2. Press the UP or DOWN key until the display shows the desired volume level.
PAGE 15
UX-A1000U [2] Diagnostics and service soft switch 1. Operating procedure (1) Entering the diagnostic mode Press FUNC → 9 → TC02 → 8 → # → 7 , and the following display will appear. / TA71 After 2 sec: DIAG MODE contorol PWB ROM TC02 printer PWB ROM TA71 Then press the START key. Select the desired item with the up key or the down key or select with the rapid key. Enter the mode with the START key.
PAGE 16
UX-A1000U 3. Diagnostic items description 3. 1. Soft switch mode 3. 6. Signals send mode This mode is used to send various signals to the circuit during FAX communication. Every push of START key sends a signal in the following sequence. Moreover, the signal sound is also output to the speaker when the line monitor of the soft switch is on. [1] No signals [8] 9600BPS (V.29) [2] 14400BPS (V.33) [9] 7200BPS (V.29) [3] 12000BPS (V.33) [10] 4800BPS (V.27ter) [4] 14400BPS (V.17) [11] 2400BPS (V.
PAGE 17
UX-A1000U 4. Entering the printer diagnostic mode Press FUNC → 9 → → 8 → # → 6 , and the following display will appear. PRINT DIAG MODE Then press the START key. Select the desired item with the up key or the down key or select with the rapid key. Enter the mode with the START key.
PAGE 18
UX-A1000U 6. 7. IJP list mode Maintenance data of the printer is output.
PAGE 19
UX-A1000U 7. How to make soft switch setting To enter the soft switch mode, press the following key entries in sequence. Press FUNCTION DATA No. 9 8 7 START START 1 2 3 4 5 6 7 8 S F T SW-A1 = 0 0 0 0 0 0 0 0 Press FUNCTION key. S F T SW-A1 = 1 0 0 0 0 0 0 0 Press key. Press key. S F T SW-A1 = 1 0 0 0 0 0 0 0 S F T SW-A1 = 1 0 0 0 0 0 0 0 Bit1 - 8 are set. S F T SW-A1 = 1 0 0 0 0 0 0 0 Press START key during setting. S F T SW-A2 = 0 0 0 0 0 0 0 0 Soft SW-A2 - SW-P7 are set.
PAGE 20
UX-A1000U 8. Soft switch description • Soft switch SW NO. SW l A1 DATA NO.
PAGE 21
UX-A1000U SW NO. SW l A6 DATA NO. Switch setting and function ITEM 1 Initial setting 0 1 Reserved 2 End Buzzer Yes No 1 3 Disconnect the line when DIS is received in RX mode No Yes 1 4 5 Equalizer freeze control (MODEM) Equalizer freeze control 7200 BPS only On No Off Yes 0 0 6 7 8 CNG transmission in manual TX mode Reserved Modem speed automatic fallback when RX Yes No Yes No 1 0 0 Remarks 0 level is under -40dBm 1 2 3 SW l B1 Recall interval No.
PAGE 22
UX-A1000U SW NO. DATA NO. 1 SW l B6 Switch setting and function ITEM 1 DTMF signal transmission level (High) Binary input 0 16 8 4 2 1 0 2 No. = 3 4 5 1 2 3 4 5 (n x 0.5dBm) EX 0 0 1 0 1 eg. Signal transmission level is set to –2.5dBm. Reserved 0 7 8 Reserved Reserved 0 0 1 2 Factory setting Light Dark Darker in dark No. 1 No. 2 0 0 Factory setting 1 0 Light 0 1 Dark 1 1 Darker in dark 0 0 No. 3 0 1 0 1 0 No.
PAGE 23
UX-A1000U SW NO. SW l E1 SW l E2 SW l E3 DATA NO. Switch setting and function ITEM 1 1 Reserved 0 2 3 Reserved Reserved 0 0 4 Reserved 0 5 Reserved 0 6 7 Reserved Reserved 0 0 8 Reserved 0 1 Reserved 0 2 3 Reserved Reserved 0 0 4 Reserved 0 5 Reserved 0 6 7 Reserved Reserved 0 0 8 Reserved 0 1 Reserved 0 2 3 Reserved Reserved 0 0 4 Reserved 0 5 Reserved 0 6 7 Reserved Reserved 0 0 8 Reserved 0 DTMF detection time SW l F1 1 No.
PAGE 24
UX-A1000U SW NO. SW l G2 SW l G3 DATA NO. Switch setting and function ITEM 1 1 2 Reserved Reserved 0 0 3 4 Reserved Reserved 0 0 5 6 Reserved Reserved 0 0 7 Reserved 0 8 1 2 Reserved Reserved Reserved 0 0 0 3 4 Reserved Reserved 0 0 5 6 Reserved Reserved 0 0 7 Choice after quiet detect 8 Reserved Busy tone detection ON/OFF time Wait response for 3sec No. 1 No.
PAGE 25
UX-A1000U SW NO. DATA NO. 1 SW l I2 Binary input No. = 16 8 4 2 1 0 1 0 2 3 4 5 0 1 1 0 1 1 0 CPC detection time 4ms 20ms 40ms 70ms 140ms 160ms 200ms 290ms No.6 No.7 No.8 0 0 0 0 1 1 1 0 0 1 0 1 1 1 0 1 1 1 1 1 1 15sec 60sec 0 0 3 4 Two way record function Toll saver Disable Disable Enable Enable 0 0 5 6 Reserved Reserved 7 8 Reserved Transfer dial recall 1 AGC maximum gain (Line) 3 4 5 6 0 0 No Binary input No. = AGC maximum gain (Mic) (10 ~ 25 dB) (1 dB step) No.
PAGE 26
UX-A1000U SW NO. SW l J1 DATA NO. Switch setting and function ITEM 1 No Yes 0 Cannot change Change allowed 0 0 No Yes 3 4 5 6 Reserved Summer time setting 1 Reserved 2 Reserved 3 Polling key 4 Off 0 Low 0 Middle 1 High 1 1 No. 8 0 1 0 1 0 OPTION 0 Yes No Low 0 No. 5 Speaker volume (5 stages) 0 Low 0 0 Middle 1 1 0 High 1 1 1 0 6 No. 6 7 No. 7 0 0 1 1 0 1 No. 8 0 1 0 1 0 0 0 No. 2 E/T/M 0 No.
PAGE 27
UX-A1000U SW NO. DATA NO. Switch setting and function ITEM 1 Paper set size 1 2 SW l L2 SW l M1 SW l M2 SW l N1 SW l N2 SW l N3 No. 1 LETTER 0 No.
PAGE 28
UX-A1000U SW NO. SW l O1 SW l O2 SW l O3 SW l O4 SW l O5 SW l O6 DATA NO.
PAGE 29
UX-A1000U SW NO. SW l P1 SW l P2 SW l P3 SW l P4 SW l P5 SW l P6 SW l P7 DATA NO.
PAGE 30
UX-A1000U SW-A2 No. 8 CNG transmission • Soft switch function description When set to "0" , this model allows CNG transmission by pressing the Start key in the key pad dialing mode. When set to "1", CNG transmission in the key pad dialing mode cannot be performed. In either case. CNG transmission can be performed in the auto dial mode. SW-A1 No. 1 Protect from echo Used to protect from echo in reception. SW-A1 No. 2 Forced 4800BPS reception SW-A3 No. 1, No.
PAGE 31
UX-A1000U SW-A5 No. 5, No. 6 Digital cable equalizer setting (Reception for Caller ID) SW-B2 No. 7, No. 8 Reserved Set to "0". Line equalization when reception for CALLER ID is to be set according to the line characteristics. Setting should be made according to distance between the telephone and the telephone company central switching station. SW-B3 No. 1 ~ No. 5 Reserved Set to "0". SW-A5 No. 7 Error criterion SW-B3 No. 6, No.
PAGE 32
UX-A1000U SW-B6 No. 1 ~ No. 5 DTMF signal transmission level (High) The transmission level of DTMF signal is adjusted. (higher frequency) Phone Number Intended Purpose 00000: 0dBm Ring Pattern ↓ 11111: -15.5 dBm (-0.5dBm x 31) SW-B6 No. 6 ~ No. 8 Reserved Set to "0". SW-C1 No. 1, No. 2 Reading slice (Binary) Used to determine the set value of reading density in standard/fine mode.
PAGE 33
UX-A1000U SW-D2 No. 4 Reserved SW-F1 No. 5 ~ No. 8 Remote operation code figure by external TEL (0 ~ 9) Set to "0". Used for Caller ID function. Remote operation codes can be changed from 0 through 9. If set to greater than 9, it defaults to 9. The "5 " is not changed. Ex-7 (Default: 5 ) SW-D2 No. 6 Caller ID detect during CI off SW-F2 No.
PAGE 34
UX-A1000U SW-I3 No. 3 Two way record function SW-H1 No. 5 Busy tone detect continuation sound detect during OGM If this switch is set to "1", the machine disables two way recording. Used to detect the continuous tone of specific frequency during OGM output. SW-I3 No. 4 Toll saver SW-H1 No. 6 Busy tone detect continuation sound detect Used to turn on the toll saver function. If it is off, the reception frequency in the AM mode is the same as in the FAX mode.
PAGE 35
UX-A1000U SW-I7 No. 1, No. 2 AGC slew rate (Line) SW-J3 No. 5 ~ No. 8 OGM/ICM output level to speaker (0dB ~ -15dB) (1dB step) The AGC Slew Rate controls the convergence of the message playback level to the desired playback level. A large slew rate will allow faster convergence and a small slew rate will allow slower convergence. Used to control OGM and ICM output level to speaker. SW-K1 No.1, No. 2 Reserved SW-I7 No. 3, No. 4 AGC slew rate (Mic) Set to "0".
PAGE 36
UX-A1000U SW-P2 No. 2, No. 3 Reserved Set to "0". SW-P2 No. 4, No. 5 Reserved Set to "1". SW-P2 No. 6, No. 7 Reserved Set to "0". SW-P2 No. 8 Reserved Set to "1". SW-P3 No. 1 Reserved Set to "1". SW-P3 No. 2 Reserved Set to "0". SW-P3 No. 3 Reserved Set to "1". SW-P3 No. 4 ~ No. 6 Reserved Set to "0". SW-P3 No. 7 Reserved Set to "1". SW-P3 No. 8 Reserved Set to "0". SW-P4 No. 1 Reserved Set to "0". SW-P4 No. 2 Reserved Set to "1". SW-P4 No. 3 Reserved Set to "0". SW-P4 No. 4 ~ No. 7 Reserved Set to "1".
PAGE 37
UX-A1000U [3] Troubleshooting Refer to the following actions to troubleshoot any of the problems mentioned in 1-4. [1] A communication error occurs. [2] Image distortion produced. [3] Unable to do overseas communication. [4] Communication speed slow due to FALLBACK. • Increase the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5. May be used in case [1] [2] [3]. • Decrease the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5. May be used in case [3].
PAGE 38
UX-A1000U [4] Error code table 1. Communication error code table G3 Transmission Code Final received signal Error Condition (Receiver side) 0 Incomplete signal frame Cannot recognize bit stream after flag 1 NSF, DIS Cannot recognize DCS signal by echo etc.
PAGE 39
UX-A1000U 3-2. Automatic document feed CHAPTER 3. MECHANISM BLOCKS 1) Use of the paper feed roller and separate plate ensures error-free transport and separation of documents. The plate spring presses the document to the paper feed roller to assure smooth feeding of the document. [1] General description 2) Document separation method: Separate plate 1.
PAGE 40
UX-A1000U 3-5. Documents requiring use of document carrier 1) Documents smaller than 148mm (W) x 140mm (L). 2) Documents thinner than the thickness of 0.06mm. 3) Documents containing creases, folds, or curls, especially those whose surface is curled (maximum allowable curl is 5mm). 4) Documents containing tears. 5) Carbon-backed documents. (Insert a white sheet of paper between the carbon back and the document carrier to avoid transfer of carbon to the carrier.
PAGE 41
UX-A1000U 3) Electrical Overview The information in this section appears in a sequence relative to the system diagram in the following figure. [2] Ink jet printer 1. Engine specifications 1) Mechanism Resolution: 600dpi x 600dpi addressability Print speed: 4PPM text with black cartridge Print swath: 8 inches Duty cycle: 250 pages per month average Dimensions: 330mm x 100mm x 130mm Weight: 1.
PAGE 42
UX-A1000U 5. Overall troubleshooting of Printer • BOTH CARRIAGE MOTOR AND FEED MOTOR ARE NG. REPLACE FU1 FUSE “FU1” OPEN OK +30V CNPRINT 1,3 NG OK CHECK RESISTANCE BETWEEN +30V AND GND.
PAGE 43
UX-A1000U • MISSING NOZZLES (RESULT OF CHECK PATTERN OR CLEAN NOZZLES) CLEAN NOZZLES NG REPLACE ANOTHER CARTRIDGE NG MISSING MANY NOZZLES CHECK IC AND CONNECTOR NO YES CHECK THE SOLDER IC1, CNHEAD1,2 (PRINTER PWB) CORRECT SOLDER NG OK CHECK +11.82V CHECK RESISTANCE BETWEEN +11.82V AND GND, SHORT OR NOT. NG OK SHORT NO CHECK +11.82V PATTERN CHECK RESISTANCE BETWEEN +30V AND GND, SHORT OR NOT. CHECK +30V NG OK REPLACE PRINTER PWB SHORT NO CHECK +30V PATTERN CHECK RESISTANCE BETWEEN +3.
PAGE 44
UX-A1000U [3] Disassembly and assembly procedures • • This chapter mainly describes the disassembly procedures. For the assembly procedures, reverse the disassembly procedures. • • The numbers in the illustration and the parts list in a same section are common to each other. Easy and simple disassembly/assembly procedures of some parts and units are omitted. For disassembly and assembly of such parts and units, refer to the Parts List.
PAGE 45
UX-A1000U 2 Document guide lower unit Parts list (Fig. 2) No. 1 Caution: The CONNECTOR COVER can be opened easily by inserting a thin head jig such as a metal stick. Q’ty No. 1 Screw (3×12) Part name 3 10 ORG sensor lever Part name 2 Document guide lower unit 1 11 ORG Sensor lever release spring 1 3 Connector cover 1 12 Paper feed gear unit 1 4 Earth sheet (2pcs.
PAGE 46
UX-A1000U 3 Operation panel unit, Control PWB unit, TEL/LIU PWB unit NOTE: For disassembly of the inside of the unit, refer to the exploded view in the parts guide. Parts list (Fig. 3) No. Part name 1 Screw (3×10) 2 Operation panel unit/ Q’ty No.
PAGE 47
UX-A1000U 4 PWB installation plate, Front cover, Upper cabinet unit Parts list (Fig. 4) No. NOTE: For disassembly of the inside of the unit, refer to the exploded view in the parts guide. Part name Screw (3×8) 2 2 Screw (3×10) 3 3 PWB installation plate 1 4 Front cover 1 5 Screw (3×10) 4 6 Screw (3×6) 1 7 Upper cabinet unit 1 2 1 1 2 2 3 PWB installation plate 5 5 Boss 5 7 Upper cabinet unit 5 6 4 Front cover Printer unit Fig.
PAGE 48
UX-A1000U 5 Upper cabinet Parts list (Fig. 5) No. NOTE: For disassembly of the inside of the unit, refer to the exploded view in the parts guide. 13 Q’ty No.
PAGE 49
UX-A1000U 6 Printer unit, Bottom cabinet Parts list (Fig. 6) NOTE: For disassembly of the inside of the unit, refer to the exploded view in the parts guide. No. Q’ty No.
PAGE 50
UX-A1000U 7 Wire treatment 1 Power Supply cable Panel cable Control PWB TEL/LIU PWB Earth cable Printer cable Speaker cable Motor cable CIS cable 2 Power Supply PWB Speaker cable CIS cable Motor cable 3 Motor cable 3 – 12
PAGE 51
UX-A1000U MEMO 3 – 13
PAGE 52
TX MT CIS UNIT LIU-PWB 4–1 D-RAM (4Mbit) FLASH(4Mbit) (PROGRAM) Driver IC CONTROL PWB ASIC FAX ENGINE (SCE214V) Operation Panel PWB (KEY) LCD IEEE1284 FLASH(4Mbit) (Back up DATA) D-RAM(16Mbit) DRSNS ORGSNS FRSNS ASIC HURRICANE PIN Printer Head FLASH(1Mbit) Thunderbolt PRINTER PWB D-RAM(16Mbit) SPIT FIRE HEAD PWB M M FDMT CRMT UX-A1000U CHAPTER 4.
PAGE 53
SPEAKER TXMT 4–2 CIS UNIT 6 2 7 CNCIS CNMT CNSP 12 PANEL PWB CNPN 12 CNPN CONTROL PWB CNLIUA CNLIUA 14 3 CNPRT CNPRG CNLCD CNPW 8 CNPW 28 POWER SUPPLY PWB PRINTER CNPRINT PWB 12 12 4 2 LCD UNIT DOWNLOAD CABLE CNHEAD2 CNFDMT CNCRMT CNHEAD1 TEL/LIU PWB FPC Program Loader Box FDMT CRMT INK PWB UX-A1000U [2] Wiring diagram
PAGE 54
UX-A1000U [3] Point-to-point diagram CIS VO VG CISVDD ΦΤ CISCLK GLED +24V TX-MOTOR TPBD– TPAD– TPBD TPAD VMT VMT 1 2 3 4 5 6 7 CNCIS VO 1 VG 2 3 CISVDD ΦΤ 4 5 CISCLK GLED 6 +24V 7 1 2 3 4 5 6 CNMT TPBD– 1 TPAD– 2 TPBD 3 TPAD 4 VMT 5 VMT 6 SPEAKER SP+ SP– 1 2 CNSP SP+ 1 SP– 2 CNPN KEN4A KEN3A KEN2A KEN1A DG +3.3V E SEN0 SEN1 SEN2 SEN3 SEN4 1 2 3 4 5 6 7 8 9 10 11 12 CNPN KEN4A 1 KEN3A 2 KEN2A 3 KEN1A 4 DG 5 +3.
PAGE 55
UX-A1000U CR-MOTOR CM+ 1 CM– 2 CNCRMT CM+ 1 CM– 2 FD-MOTOR FMB– FMA– FMB+ FMA+ CNFDMT FMB– 1 FMA– 2 FMB+ 3 FMA+ 4 1 2 3 4 CNHEAD1 GND 1 ACLK 2 AGATE 3 +3.3V 4 +11.82V 5 +11.82V 6 PCLK 7 +30V 8 PD3 9 PD2 10 PD1 11 PD0 12 PRINTER PWB CNHEAD2 GND 1 PLOAD 2 PENABLE 3 NHOME 4 LHCS 5 LCN 6 OK2PRT 7 NHDRESET 8 ID1 9 ID2 10 PHASE A 11 PHASE B 12 CNHEAD1 1 GND 2 ACLK 3 AGATE 4 +3.3V 5 +11.82V 6 +11.
PAGE 56
UX-A1000U 3. Operational description CHAPTER 5. CIRCUIT DESCRIPTION Operational descriptions are given below: • [1] Circuit description When a document is loaded in stand-by mode, the state of the document sensor is sensed via the 1 chip fax engine (SCE214V). With depression of the START key in the off-hook state, transmission takes place. Then, the procedure is sent out from the modem and the motor is rotated to move the document down to the scan line.
PAGE 57
UX-A1000U [2] Circuit description of control PWB 3) DMA Channels 1. General description Six internal DMA channels support memory access for scanner, T.4/T.6, and resolution conversion. DMA Channel 2 can be reprogrammed for external access to thermal printing, thermal transfer, or plain paper inkjet printing. Fig. 2 shows the functional blocks of the control PWB, which is composed of 5 blocks.
PAGE 58
UX-A1000U 11) Video Processing 19) Power Up/Down Control The CX06835 supports two modes of shading correction for scanner data non-uniformity arising from uneven sensor output or uneven illumination. Corrections are provided on either an 8-pixel group or are applied separately to each pixel. Dark level correction and gamma correction are also provided. Two-dimensional Error Diffusion/Dithering is performed on halftone images.
PAGE 59
UX-A1000U SCE214V (IC16) Terminal descriptions Pin No.
PAGE 60
UX-A1000U SCE214V (IC16) Terminal descriptions Pin No.
PAGE 61
UX-A1000U SCE214V (IC16) Terminal descriptions Pin No.
PAGE 62
UX-A1000U (3) Panel control block The following controls are performed by the SCE214V.
PAGE 63
UX-A1000U (5) Modem block (CX20438) Integrated Analog Control Resisters for CX20438 The CX20438 IA can be used as a Primary Integrated Analog (PIA) codec or as a Secondary Integrated Analog (SIA) codec, depending on the signal connection with the SCE Controller ASIC device. In the SCE100 product, both the PIA and the SIA are packaged external to the SCE Controller device, whereas in the SCE214V, the PIA is packaged with the SCE214V Controller and the SIA is external.
PAGE 64
UX-A1000U (6) IC12 (µPD65944) Hardware description Serial data reception from FaxEngine FaxEngine external bus connection Resolution conversion/image zooming (70 % - 200 %) Main scan: 203.3 dpi 600 dpi Sub scan: 97.79 dpi/195.58 dpi/391.
PAGE 65
Serial data receiving circuit 203 dpi data buffer Main scanning direction resolution conversion circuit Main scan 600 dpi data buffer Sub scanning direction resolution conversion circuit Sub scan 600 dpi data buffer Printing dot calculation circuit Print duty judging circuit Swath conversion circuit ESC command adding circuit Command transmission buffer Response receiving buffer IEEE1284 controller Fax Engine bus interface Memory controller/arbiter Overall data conversion controller UX-A1000U Functional b
PAGE 66
UX-A1000U 6) Sub scanning direction resolution conversion circuit 14) FaxEngine bus interface It reads 1 byte (8 dots in the main scanning direction) of data in the main scan 600 dpi data buffer, converts the resolution in the sub scanning direction, and stores the data in the sub scan 600 dpi data buffer. Then it repeats this operation every 8 dots until reaching the end of line. It further converts the data for 208 lines and sends out the completion pulse when finished.
PAGE 67
UX-A1000U µPD65944 (IC12) Terminal descriptions PIN NO.
PAGE 68
UX-A1000U [3] Circuit description of TEL/LIU PWB (1) TEL/LIU block operational description 1) Block diagram TEL/LIU PWB CONTROL PWB IC101A RTLOOP (20438 I/A) LINE EXIT SIGTX H HS DETECTOR TXOUT L CML SP OUT CI DETECTOR SIGRX RXIN MIC ENABLE MICP TELOUT IC101B 0,6dB 0,1 0,0 1,0 1,1 SPKRP ENABLE MIC /LINE SELECT LINEIN SIN DAC LPF LINE IN ENABLE 0,20,25,30dB IC101C RX DTMFMUTE Q102 ADC TEL IN TEL MUTE (H:MUTE) TX HANDASET MIC MUTE (H:MUTE) LINE OUT ENABLE RCVOL IC101D Q103
PAGE 69
UX-A1000U LINEOUT A RCVOL DTME VOL A (HIGH) (LOW) MUTE VOLUME SETTING Receiver volume setting Low Middle High Fixed 1 1 0 1 DTMF Transmission volume setting (Receiver) Key buzzer volume setting Fixed Speaker volume setting Level1 Level2 Level3 Level4 Level5 Ringer volume setting Low Middle High DTMF speaker volume Level1 setting Level2 Level3 Level4 Level5 OGM playback speaker Level1 volume setting Level2 Level3 Level4 Level5 ICM record speaker Level1 volume setting Level2 Level3 Level4 Level5 VOL B [
PAGE 70
UX-A1000U [4] Circuit description of Printer PWB 1. Block diagram PD(8:1) PCLK PDAT SCE214V PLAT MAIN CLOCK PRINTER HEAD HURRICANE µPD65944 CONTROL SIGNAL SERIAL TRANSFER 11.82V THUNDERBOLT FD MOTOR CR MOTOR Fig. 8 2. Circuit description The printer control unit consists of a printer controller ASIC (IC1:Hurricane), printer controller CPU bus connection ASIC(With control PWB), and analog ASIC(IC3: Thunderbolt) with a built-in motor driver and head voltage generating circuit.
PAGE 71
UX-A1000U Hurricane (IC1) Terminal descriptions Pin No.
PAGE 72
UX-A1000U Hurricane (IC1) Terminal descriptions Pin Name I/O D8 D9 D10 D11 D12 D13 D14 D15 DRAM_nRAS DRAM_nLCAS I/O I/O I/O I/O I/O I/O I/O I/O O O 172 DRAM_nUCAS O 175 177 195 196 199 200 190 188 187 185 183 178 144 147 151 153 163 165 166 169 158 157 156 155 143 141 139 138 164 171 173 176 179 181 184 186 189 192 DRAM_nWE DRAM_nOE DRAM_A0 DRAM_A1 DRAM_A2 DRAM_A3 DRAM_A4 DRAM_A5 DRAM_A6 DRAM_A7 DRAM_A8 DRAM_A9 DRAM_D00 DRAM_D01 DRAM_D02 DRAM_D03 DRAM_D04 DRAM_D05 DRAM_D06 DRAM_D07 DRAM_D08 DRAM_D09
PAGE 73
UX-A1000U [5] Circuit description of power supply PWB 1. Block diagram TRANSFORMER INPUT (1) FILTER CIRCUIT BLOCK (2) (3) SWITCHING CIRCUIT BLOCK RECTIFICATION AND SMOOTHING CIRCUIT BLOCK (5) 30V CIRCUIT BLOCK 30V (6) 5V CIRCUIT BLOCK 5V (4) CONTROL CIRCUIT BLOCK GND PHOTO-COUPLER Fig. 10 This power supply unit has the function to convert the A110-120V(50/60Hz) to DC5V, and provide these outputs to the equipment. The following explains the function of each block. 2-1.
PAGE 74
1 2 3 4 PLAT A (1-1D) ENABLE (4-2A) (4-2A) PDAT (4-2A) PCLK CNCIS-4 CNCIS-5 <øT > øT CISCLK C202 (4-2A) CLOCK C108 DG C200 5 C201 R223 N.M. B DG C230 100pF/50V 270 R213 0 270 R212 270 R208 270 150 R207 N.M. C109 R211 DG E DG CNPN-7 60 59 58 57 63 62 61 67 69 11 2200pF/50V x5 C244 C227 C243 C245 C228 N.M. C12 10 32 33 +3.
PAGE 75
6–2 A CE A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 D0 D1 D2 D3 D4 D5 D6 D7 WE OE GND VDD IC5 7 32 24 8 21 22 23 25 26 27 28 29 B Pm39LV040-70 30 20 19 18 17 16 15 14 13 3 2 31 1 12 4 5 11 10 6 9 C D0 D1 D2 D3 D4 D5 D6 D7 DG (1-3I) FLCS- C126 0.1u/50V +3.3V D R146 10K +3.
PAGE 76
6–3 1 2 3 4 5 6 A CNLIUA-3 CNPRT- 26 (6-1H) VOLA (6-1H) VOLB (6-1H) VOLC CNPRT-27 CNPW-9 CNPRG-3 CNPRG-1 (4-4A) ASICRES (4-2B) WAIT (7-4C) FRSNS(7-2C) ORGSNS(7-5C) DRSNS (6-5E) LEDON CNLIUB-2 (6-2D) W-TONE CNLIUB-1 CNLIUA-9 (6-4E) CNLIUA-5 (6-5E) (6-3E) RCVOL (6-3E) DTMFMUTE (6-1A) SIGMUTE (6-1I) SPMUTE CNLIUA-12 CNLIUA-11 CNLIUA-10 R187 N.M. PRTRES PSAVE MICMUTE R206 270 B DG C264 N.M. DG CNPRT-2 8 C242 N.M. SN_Cover C R165 270 R190 R186 R209 N.M. R185 N.
PAGE 77
1 2 3 4 A (1-5A) CLOCK (1-3A) PLAT (1-3A) PCLK (1-3A) PDATA (1-3I) GACS(2-3A) (1-3I) RD(2-3A) (1-3I) WR- (2-5A) (1-6I) D[7:0] (2-6A) (1-5I) A[5:0] (3-3A) ASICRES DG 22 7 23 8 6 10 11 12 13 16 17 18 19 20 9 NC D[7:0] A[5:0] OE WE +3.3VAS RA17 100 8 7 6 5 RA13 100 8 7 6 5 D0 D1 D2 D3 D4 D5 D6 D7 SD0 SD1 SD2 SD3 SD4 SD5 SD6 SD7 C A0 A1 A2 A3 A4 A5 56 DG 8 7 6 5 N.M.
PAGE 78
1 2 3 4 5 +3.3V VG R103 R105 51K 5.1 220 (2W) R124 N.M. R1 VG DG L100 0 150u/6V C1 B VG DG C101 0.1u/50V GLED VG CISVDD 1000p/50V C102 0.1u/50V CISVDD Q100 2SA1530AS C103 C A B C This mark indicates a safety-critical part(s). NOTE: (5-4I) LEDON- CNCIS-1 R104 5.1K E C 6 CISVDD Video processing/Motor driver B CNCIS-6 CNCIS-2 CNCIS-3 +30V D KAB5002 201 FU101 VIN (1-1F) D (1-1E) TPB- 11 (2W) E (3-3A) LEDON R226 N.M.
PAGE 79
1 2 3 4 5 MAG TXOUT RXIN A B C287 R200 BLM18HG102SN1D ZD100 0 C184 MAG C186 1u/10V-K B N.M. C286 Q102 RT1N141C C 1u/10V-K L1 N.M. R178 0 C191 39K 0 R156 Q104 C C282 1u/10V C SIGTX MAG B C284 D 5 4 20K E DG MAG R130 3 2 1 C115 4700p/50V IC9 RCVOL (3-5A) (6-5E) DTMFMUTE (3-5A) CNLIUA-4 CML (3-4A) SIGRX (3-3H) RCVOL (3-5A) (6-3E) TELOUT1 (3-2H) C142 (3-2H) SPOUT DG +3.
PAGE 80
1 2 3 4 5 R101 430 R175 430 +5V DG R108 430 +5V DG DG PH1 ORGSNS GP1S58VS PH2 FRSNS GP1S58VS PH100 DRSNS GP1S58VS 270 R106 270 R171 270 R102 DG ORGSNS FG3 C104 1000p/50V DG FRSNS C152 1000p/50V DG DRSNS C100 1000p/50V A B C FG1 ORGSNS (3-3A) FRSNS (3-3A) DRSNS (3-3A) FG3n C This mark indicates a safety-critical part(s).
PAGE 81
UX-A1000U Control PWB parts layout (Top side) DRSNS [BROWN] ORGSNS [ORANGE] FRSNS [RED] 6–8
PAGE 82
UX-A1000U Control PWB parts layout (Bottom side) FU100 FU101 6–9
PAGE 83
1 2 3 4 L2 EX-T2 T2 ARG RA501P-C6 AR1 AR3 C1 L5 L6 JP5 JP4 L2 JP3 L4 JP N.M N.M JP JP N.M N.M N.M L1 JP JP6 A This mark indicates a safety-critical part(s). NOTE: CNTLJ-4 CNLNJ-2 CNLNJ-3 CNLNJ-4 L1 N.M RA501P-C6 CNLNJ-5 RA-391P-V6-2 AR2 T1 L3 3 CML1A 5 N.M B A5X24E908 4 C101 JP JP R4 0.
PAGE 84
1 2 CNHJ-3 CNHJ-2 CNLIUA-3 CNHJ-1 CNHJ-4 C131 C108 1u(2125) MICMUTE RX- RX+ TX- TX+ A 2200p 1SS355 3 C104 B N.M E C RT1N436C Q102 620 N.M ( 1-4E) R127 C127 L8 L9 V ref A JP JP9 R-5C N.M N.M N.M R113 V ref A N.M JP JP10 L7 C126 JP8 1.5k R119 1k C119 R125 R123 +24VA HSDG DG R14 100(1/4W) V ref B 1u C123 C14 22u/50V DG R122 B DG 1k R120 C120 DG 1000p C124 N.M C121 B Q2 KTC3198GR-AT 3.3k DG + + N.
PAGE 85
1 2 3 DG A5X24E908 CML1B 1SS133 D2 PC1B PC814X DG DG 1000p C DG B Q101 RT1N436C 1000p HS- CML CNLIUA-9 CNLIUA-11 CNLIUA-10 A This mark indicates a safety-critical part(s). NOTE: +24V DG N.M PC3B C103 C105 4 3 DG PC2B PC817X4 Ci B + V ref A +24VA V ref B DG +24VA IC101E HA17324A 22u/50V 4 C C ZD9 HZ6A3 R13 2k(1/2W) DG 11 4 B V ref A C13 TEL/LIU PWB circuit 4 3 0.1u(2125) (1608 & 2125) 0 C114 R109 R110 6 – 12 E + +24V D101 DG + + C8 N.
PAGE 86
UX-A1000U TEL/LIU PWB parts layout (Top side) TEL/LIU PWB parts layout (Bottom side) 6 – 13
PAGE 87
1 2 3 4 5 6 DG A DG 0.1u C158 0.1u 0.1u C142 0.1u C131 ASIC_+2.5V +3.3V 0.1u 0.1u 0.1u C141 C161 0.1u GND WP 4 7 8 0.1u C140 C162 0.1u C157 0.1u C183 B 0.1u C185 0.1u C134 ASIC_+3.3V 0.1u 0.1u 0.1u C168 C156 0.1u C133 C186 DG 0.1u C144 +3.3V ACLK 0.1u C128 0.1u C160 0.1u 0.1u C169 0.1u C127 C143 0.1u N.M. C170 N.M. C135 ASIC_+3.
PAGE 88
6 – 15 1 2 3 4 5 6 MG R133 R132 R131 R130 N.M. +11.82V MG ZD1 N.M. C174 2200p C172 0.1u FG C5 220u/25V C175 2200p C171 2700p_BK DG C173 2200p A B DG DG C C176 0.01u MG +30V 4 D CP1 CP2 GND GND VPH_FB FU1 D MG MG +VM VCP VBULK VBULK VBULK VBULK VBULK VBULK VBULK E R122 R124 R123 33 13 12 14 34 32 26 20 19 21 27 25 1 11 15 16 23 30 31 35 N.M.
PAGE 89
6 – 16 1 2 3 4 5 6 B A B (1-2H) (1-2H) (1-2H) (1-2H) (1-2H) Printer PWB circuit A DRAM_nRAS DRAM_nLCAS DRAM_nUCAS DRAM_nWE DRAM_nOE C205 330p C (1-4G) ROM_nCE (1-4G) ROM_nOE (1-4G) ROM_nWE C200 100p C203 330p R159 10K +3.3V C201 330p (1-6H) A[1..16] C204 330p (1-4H) DRAM_A[0..
PAGE 90
6 – 17 1 2 3 4 5 6 A +3.3V B LatchHtrCS LCN OK2PRT PRTRESEn_PhID1 En_PhID2 SNR_ChB SNR_ChA A PLOAD PENABLE PH_D3 PH_D2 PH_D1 PH_D0 (4-5C) (4-5C) (4-5C) (4-5C) (1-2C) (1-2C) (4-6C) (1-6C) (4-6C) (4-6C) (1-5E) (1-5E) PCLK (1-3C) (4-5C) (4-5C) ACLK AGATE SF_penable SF_pdata0 SF_pdata1 SF_pdata2 SF_pdata3 SF_pload SF_phid1 SF_phid2 SF_agate SF_ok2prt (1-3C) (4-6C) (1-3E) (1-3E) (1-3E) (1-3E) (1-3E) (1-3E) (1-3E) (1-3E) (1-2E) (1-2E) +VM R168 N.M.
PAGE 91
UX-A1000U Printer PWB parts layout (Top side) P-IN [YELLOW] FU1 [GREEN] +3.
PAGE 92
UX-A1000U Printer PWB parts layout (Bottom side) 6 – 19
PAGE 93
1 2 3 4 C6 C7 Z1 Q1 C1 R1 R41 Q2 R19 C10 L1 C9 R12 R6 R7 A B C This mark indicates a safety-critical part(s). NOTE: FG 3 D5 5 R5 F1 D11 D12 D7 N.M. R9 1 CNAC C8 BEA1 D4 D3 C5 R10 D R2 R3 D8 D10 D13 PC1 2 3 4 6 T1 12 9 8 D101 C111 E D103 D102 E N.M. C101 N.M. C103 C102 6 D F N.M. F FG R112 G R107 R103 G C110 BEA101 F102 R111 [4] Power supply PWB circuit R11 R13 D6 R17 6 – 20 C11 R106 VR101 R115 R110 PC1 IC101 C D106 N.M.
PAGE 94
UX-A1000U Power supply PWB parts layout (Top side) Power supply PWB parts layout (Bottom side) 6 – 21
PAGE 95
6 – 22 A B C D A KEN3A KEN4A CNPN-2 CNPN-1 +3.3V DG CNPN-6 CNPN-5 CNPN-7 KEN2A CNPN-3 A CNLCD-4 CNPN-4 E SEN4 SEN3 CNLCD-14 SEN2 CNLCD-13 SEN1 CNLCD-12 SEN0 KEN1A CNPN-12 CNPN-11 CNPN-10 CNPN-9 CNPN-8 CNLCD-11 RS LD3 LD2 LD1 LD0 GND VCC D1 D2 D3 D4 D5 D6 D7 D8 D9 + C3 22u/50V 74HC147 NC A3 A2 A1 A0 IC1 1N4148 D1 1N4148 D2 1N4148 D4 1N4148 D5 1N4148 D3 DG C2 22000p +3.3V R4 100k +3.
PAGE 96
UX-A1000U Operation panel PWB parts layout Note: Since the parts of PWB cannot be supplied, change it as a unit.
PAGE 97
1 2 3 4 5 6 A CNHEAD2 CNHEAD1 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12 PHASE A PHASE B B GND C108 0.1 GND PLOAD PENABLE nHOME LHCS LCN OK2PRT NHDRESET ID1 GND ACLK AGATE +3.3V +11.82V +11.82V PCLK +30V PD3 PD2 PD1 PD0 R103 R100 R101 0 39 39 2 1 4 6 5 3 [6] Ink PWB circuit B ENC1 GP1A038RBKL R106 180 C101 180P GND C100 180P C111 0.1 C +11.82V C N.M. C103 GND R107 5.1K N.M. N.M.
PAGE 98
UX-A1000U Ink PWB parts layout (Top side) FPC Ink PWB parts layout (Bottom side) FPC 6 – 25
PAGE 99
UX- A1000U CHAPTER 7.
PAGE 100
UX-A1000U [2] Power on sequence START CPU initialized MODEM initialized “WAIT A MOMENT” display STOP key ? NO “MEMORY CLEAR ?” display NO 3 sec ? YES 1 YES STAND-BY START key ? NO 2 YES COPY key ? 1 2 “MEMORY CLEARED” display “MEMORY CLEARED” display Memory clear Memory clear STAND-BY PROCESS CHECK MODE NO YES STOP key ? NO 3 sec ? NO YES STAND-BY 7–2
PAGE 101
UX-A1000U CHAPTER 8. OTHERS [1] Service tools 1. List NO. PARTS CODE DESCRIPTION Q’TY PRICE RANK 1 CPWBX3312SCS1 Extension board unit (Control PWB) 1 CA 2 CPWBX3318SCS1 Extension board unit (Printer PWB) 1 CA 3 PSHEZ3579SCZZ Shading wave memory standard paper 1 AD Q’TY PRICE RANK Extension Control board unit 100 Extension Control PWB unit (CPWBX3312SCS1) NO.
PAGE 102
UX-A1000U Extension Printer board unit Extension Printer PWB unit (CPWBX3318SCS1) NO.
PAGE 103
UX-A1000U 2. Description 2-1. Control PWB CHK Install the extension PWB X3312 in the main unit. (Replace X3431.) ,,, QCNWG348BSCZZ RED BROWN ORANGE QCNWG338BSCZZ QCNWG339BSCZZ QCNWG344BSCZZ QCNWG345BSCZZ QCNWG349BSCZZ QCNWG355BSCZZ ORGSNS (ORANGE) PH1 FRSNS(RED) DRSNS (BROWN) PH100 PH1 (HOOK-SW) PH2 CHECK TEL/LIU PWB (F3309) CHECK CONTROL PWB (X3431) * Block the groove in each PH like . Hook-SW (PH1 of TEL/LIU F3309) should be turned on/off manually.
PAGE 104
UX-A1000U 2-2. Printer PWB CHK Install the extension PWB X3318 in the main unit. (Replace X3346.) QCNWG342BSCZZ QCNWG340BSCZZ QCNWG341BSCZZ QCNWG355BSCZZ "RED" CNHEAD1 [RED] CHECK PRINTER PWB (X3346) "BLUE" CNHEAD2 [BLUE] PI1 QCNWG343BSCZZ * Block the groove in PI1 like . Notes: • Match the colors of the silk listed on the PWB and of the cable as shown above when connecting. • On the extension PWB X3318, match the color of the silk listed on the PWB and of the cable as shown below when connecting.
PAGE 105
UX-A1000U 2-3. Simultaneous CHK on Control PWB and Printer PWB • Install the extension PWB X3312 in the main unit. (Replace X3431.) • Install the extension PWB X3318 in the main unit. (Replace X3346.) Notes: Be sure to follow the notes in "2-2. Printer PWB CHK". ,,,, ,,,, QCNWG342BSCZZ QCNWG364BSCZZ QCNWG340BSCZZ QCNWG341BSCZZ GREEN "RED" YELLOW CNPRT +3.
PAGE 106
UX-A1000U 2-4. Shading paper The white and black basis is applied to remember the shading waveform. Be sure to perform this operation when replacing the battery or replacing the control PWB. Execute in the shading mode of DIAG mode. SHADING WAVE MEMORY STANDARD PAPER (PSHEZ3579SCZZ) [2] Changing the record paper size How to change the A4 size and letter size of the record papers 1) It becomes the record paper of the A4 size by installing A4 guide (PGiDM2493AXSA) which shows in the drawing.
PAGE 107
UX-A1000U PARTS GUIDE UX-A1000 MODEL MODEL SELECTION CODE DESTINATION UX-A1000 U U.S.A. CONTENTS 1 Cabinet, etc.
PAGE 108
UX-A1000U [1] Cabinet,etc.
PAGE 109
UX-A1000U NO. PARTS CODE PRICE RANK NEW MARK PART RANK CA BE AL BA AM AQ BF BF AS AQ AD AA AC AC AP AQ AS AP AR AF AP AE AG AP AM AM AE AD AE AD AE AD AC AK AC AD AD AC AD AD AC AE AE AR AG AD AD AU AB AH AD AB AP AE AE AP AP AM AY AE AE BK AY BN AE AC AC AC AB AA AA AA AA AA AA AA N N E D C E E E E D C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C B C C C B B E B B C C C C C C C C C C C C DESCRIPTION [1] Cabinet,etc.
PAGE 110
UX-A1000U [2] Operation panel unit/Document guide upper 2 901 3 1 27 29 26 18 12 16 11 28 23 8 4 13 9 B1 19 10 7 B2 14 6 25 B1 5 17 21 24 B1 15 20 NO.
PAGE 111
UX-A1000U [3] Document guide lower 14 3 15 16 17 4 8 5 18 9 11 7 6 10 18 B1 1 2 NO.
PAGE 112
UX-A1000U [4] Printer unit 41 16 50 23 52 16 45 61 53 16 3 61 7 16 B2 22 61 6 31 58 57 61 14 47 21 B3 46 40 29 19 19 51 11 66 64 B3 28 56 20 59 26 5 49 A B3 69 68 35 B3 B3 30 18 4 44 B3 62 10 B1 33 54 13 55 37 A 1 67 48 2 B4 43 60 65 34 32 34 34 60 42 36 38 12 25 B4 39 43 60 60 8 24 15 9 –5– 63 17
PAGE 113
UX-A1000U PARTS CODE NO.
PAGE 114
UX-A1000U [5] Packing material & Accessories 15 14 11 TAPE 24 TAPE 9 25 5 20 8 2 26 10 28 23 18 4 13 TAPE 7 19 16 AC Cord 22 3 17 1 NO.
PAGE 115
UX-A1000U NO.
PAGE 116
UX-A1000U NO.
PAGE 117
UX-A1000U NO.
PAGE 118
UX-A1000U NO.
PAGE 119
UX-A1000U NO.
PAGE 120
UX-A1000U NO.
PAGE 121
UX-A1000U NO.
PAGE 122
UX-A1000U NO.
PAGE 123
UX-A1000U NO. PARTS CODE PRICE RANK NEW MARK PART RANK DESCRIPTION [11] Ink PWB unit 19 20 21 22 23 901 VRS-CZ1JB392J VRS-CZ1JB181J VRS-CZ1JB512J VRS-CZ1JB512J PSHEP3680XHZZ (Unit) DCEKH435CXH01 AD AA AD AD AD C C C C C Resistor(1/16W 3.9KΩ ±5%) Resistor(1/16W 180Ω ±5%) Resistor(1/16W 5.1KΩ ±5%) Resistor(1/16W 5.
PAGE 124
UX-A1000U Index PARTS CODE [C] CCHSM2076XH01 CCNWN337BXH01 CGERH2614XH01 CPAKC364FXH01 CPLTM3258XH01 CROLP2499XH01 CROLR2362XH03 CROLR2362XH04 CROLR2497XH01 CROLR2498XH01 [D] DCEKC887SXHZZ ″ DCEKH435CXH01 ″ DCEKL434CXH01 ″ DCEKP438CXH11 DCEKP439CXH03 ″ DCEKP440CXH01 ″ DUNTK497CXHMG [G] GCABA2418XHSD GCABB2419XHSD GCASP2167XHZZ GCASP2168XHSK GCOVA2458XHSC GCOVA2465XHZZ GCOVA2466XHZZ GCOVA2467XHSD GCOVA2477XHSC GLEGG2078XHZZ [H] HPNLH2426XHZK [J] JBTN-2381XHSB JBTN-2382XHSD JBTN-2383XHSC JBTN-2384XHSA JBTN-2
PAGE 125
UX-A1000U PRICE NEW PART RANK MARK RANK PARTS CODE No.
PAGE 126
UX-A1000U PARTS CODE No.
PAGE 127
UX-A1000U PRICE NEW PART RANK MARK RANK PARTS CODE No.
PAGE 128
UX-A1000U COPYRIGHT © 2003 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. SHARP CORPORATION Communication Systems Group Quality & Reliability Control Center Higashihiroshima, Hiroshima 739-0192, Japan Printed in U.S.A.