Installation guide

e1mdlCsmFDA-rev0512
www.versamatic.com
Model E1 Metallic Bolted • 2
Materials
Material Prole:
Operating
Temperatures:
Max. Min.
Conductive Acetal: Tough, impact resistant, ductile. Good
abrasionresistanceandlowfrictionsurface.Generallyinert,with
goodchemicalresistanceexceptforstrongacidsandoxidizing
agents.
190°F
88°C
-20°F
-29°C
EPDM:Showsverygoodwaterandchemicalresistance.Has
poor resistance to oils and solvents, but is fair in ketones and
alcohols.
280°F
138°C
-40°F
-40°C
FKM:(Fluorocarbon)Showsgoodresistancetoawiderange
of oils and sovents; especially all aliphatic, aromatic and
halogenated hydrocarbons, acids, animal and vegetable oils.
Hotwaterorhotaqueoussolutions(over70°F)willattackFKM.
350°F
177°C
-40°F
-40°C
Hytrel®: Good on acids, bases, amines and glycols at room
temperatures only.
220°F
104°C
-20°F
-29°C
Neoprene: All purpose. Resistance to vegetable oils. Generally
not affected by moderate chemicals, fats, greases and many
oilsandsolvents.Generallyattackedbystrongoxidizingacids,
ketones, esters and nitro hydrocarbons and chlorinated aromatic
hydrocarbons.
200°F
93°C
-10°F
-23°C
Nitrile: Generalpurpose,oil-resistant.Showsgoodsolvent,oil,
waterandhydraulicuidresistance.Shouldnotbeusedwith
highlypolarsolventslikeacetoneandMEK,ozone,chlorinated
hydrocarbons and nitro hydrocarbons.
190°F
88°C
-10°F
-23°C
Nylon: 6/6Highstrengthandtoughnessoverawide
temperaturerange.Moderatetogoodresistancetofuels,oils
and chemicals.
180°F
82°C
32°F
0°C
Polypropylene:Athermoplasticpolymer.Moderatetensile
andexstrength.Resistsstongacidsandalkali.Attackedby
chlorine,fumingnitricacidandotherstrongoxidizingagents.
180°F
82°C
32°F
0°C
PVDF:(PolyvinylideneFluoride)Adurableuoroplasticwith
excellentchemicalresistance.ExcellentforUVapplications.
High tensile strength and impact resistance.
250°F
121°C
0°F
-18°C
Santoprene®:Injectionmoldedthermoplasticelastomerwith
nofabriclayer.Longmechanicalexlife.Excellentabrasion
resistance.
275°F
135°C
-40°F
-40°C
UHMW PE: A thermoplastic that is highly resistant to a broad
rangeofchemicals.Exhibitsoutstandingabrasionandimpact
resistance,alongwithenvironmentalstress-crackingresistance.
180°F
82°C
-35°F
-37°C
Urethane:Showsgoodresistancetoabrasives.Haspoor
resistance to most solvents and oils.
150°F
66°C
32°F
0°C
Virgin PTFE:(PFA/TFE)Chemicallyinert,virtuallyimpervious.
VeryfewchemicalsareknowntochemicallyreactwithPTFE;
moltenalkalimetals,turbulentliquidorgaseousuorineand
afewuoro-chemicalssuchaschlorinetriuorideoroxygen
diuoridewhichreadilyliberatefreeuorineatelevated
temperatures.
220°F
104°C
-35°F
-37°C
Maximum and Minimum Temperatures are the limits for which these materials can be operated.
Temperatures coupled with pressure affect the longevity of diaphragm pump components.
Maximum life should not be expected at the extreme limits of the temperature ranges.
Metals:
Alloy C:EqualtoASTM494CW-12M-1specicationfornickelandnickelalloy.
Stainless Steel: EqualtoorexceedingASTMspecicationA743CF-8Mforcorrosion
resistant iron chromium, iron chromium nickel and nickel based alloy castings for
general applicaitons. Commonly referred to as 316 Stainless Steel in the pump industry.
For specic applications, always consult the Chemical Resistance Chart.
CAUTION! Operating temperature limitations are as follows:
AFTERMARKET PARTS
Pumper Parts is your single source for parts that
t Air-Operated Double Diaphragm (AODD) pumps
• Wilden
®
• ARO
®
• Yamada
®
RIGHT PART, RIGHT NOW
Designed to perform equal to or greater
than original equipment manufacture.
Phone: [phone]
info@pum perparts.com
www.pumperparts.com
Pumper Parts and its products are not affiliated with any of the original equipment manufacturers referenced herein. All original equipment manufacturers’ names, colors, pictures, descriptions and part numbers are used for identification
purposes only. Pumper Parts
®
is a registered trade name of IDEX Corporation. All other trademarks, registered trademarks and product names are the property of their respective owners. Yamada
®
is a registered trademark of
Yamada Corporation. ARO
®
is a registered trade name of Ingersoll-Rand Company. Wilden
®
is a registered trade name of Wilden Pump and Engineering Company, a Dover Resources Company.
MODEL SPECIFIC UNIVERSAL ALL AODD
1: PUMP SPECS