User's Manual

User Manual of Remote for Skateboard HW6123ENG-20171221
Thank you for purchasing this HOBBYWING product! Any improper operation may cause the unit to function abnormally or even
damage relevant devices, so we strongly recommend reading through this user manual before use. Because we have no control over
the use, installation, or maintenance of this product, no liability may be assumed for any damage or losses resulting from the use of
the product. We do not assume responsibility for any losses caused by unauthorized modifications to our product. Besides, we have
the right to modify our product design, appearance, features and usage requirements without notification. We, HOBBYWING, are
only responsible for our product cost and nothing else as result of using our product.
01 Specifications
02 Image
03 Functions & Instructions
1) Power On
(With the remote powered off), press the “Button A” (on the remote) for 1 second, the remote vibrates a short vibration, enters the
connecting mode, and the signal LED starts to flash Red slowly (once a second). (With the board powered off), press the “Power”
button on the board (for 0.2 second) to enter the “connecting” mode, and the Red LED on it starts to flash slowly (once a second).
Note: the signal LED on the remote and the Red LED on the board turn solid after they are connected to each other.
2) Power Off
(Power off) manually: (with the remote & the board powered on), pressing the “Button A” on the remote for 2 seconds can turn off
the remote, the remote will vibrate a short vibration after the press; pressing the “Power” button on the board for 1 second can turn
off the board.
Note: if the remote is still on after the board is turned off, the signal LED on the remote will flash Red slowly and vibrate once to
remind the user. Similarly, if the board is still on after the remote is powered off, the Red LED on the board will flash slowly (to warn
the user.)
(Power off) Automatically: if the user let the board stay still with no further operation for 5 minutes, then the remote and the board
will turn off automatically.
3) Connecting & Binding (Remote & Board are bound before leaving the factory)
(With the remote & the board powered off,) press the “Power” button on the board for 5 seconds, the Red LED (on it) starts to flash
rapidly to indicate that the board enters the binding mode; then press the “Button A” on the remote for 5 seconds, the Signal LED (on
it) starts to flash Red rapidly to indicate that the remote enters the binding mode, and the remote vibrates two short vibrations and one
long vibration to indicate that the binding succeeds. The signal LED on the remote and the Red LED on the board turn solid when
the binding succeeds.
Note: when using a new remote and a new board, there is no need to press either the Power button (on the board) or the Button A (on
the remote) for 5 seconds to bind them. They enters into the binding mode when they are powered on.
4) Power Indicators
Remote Power Indicator (a single LED): after the remote is powered on, if it detects the power is less than 25% (which can barely
support an one-hour operation), the Remote Power LED comes on Red; if the power is sufficient (that is the power can support an
operation of at least one hour), then the Remote Power LED comes on Green.
If there is only 5% of power (which can only support a 15-minute operation) left, the remote will vibrate a double, long vibration
(vibrate for 0.5 second, pause for 0.5 second and then vibrate again for 0.5 second ) and the Remote Power LED starts to flash Red
slowly (once a second); if there is only 2.5% of power left, the remote will vibrate a double, long vibration again (the same as the
previous) and the Remote Power LED starts to flash Red slowly; and if the power is below the regulated value (3.4V) for safe use
and the board stops, the remote will vibrate a short vibration and then turn off automatically.
Board Power Indicator (4 LEDs in a row): one LED comes on to indicate there is still 25% of power, one LED flashes to indicate
there is only 12.5% of power left. For example, if the power ranges from 62.5% to 75%, then the four LEDs will display in this way
“○●●●”; if the power ranges from 50%~62.5%, then the four LEDs will display in this way “ ○☉ ●● ”; if the power is below 25%,
the remote will vibrate a double, long vibration and the four LEDs will display in this way “○○○●” ; if the power is below 12.5%,
the remote will vibrate a double, long vibration and the four LEDs will display in this way “ ○○○☉ ”; and if the voltage goes below
the regulated value for safe use, then the power output will be cut off. At this time, it’s better to stop using as soon as possible.
Notes: the remote will display the power of the remote & the board for 2 seconds and then stop when it’s powered on and connected
to the board. Press the Button A at any time can re-trigger the display of the power of the remote & the board.
the remote only displays the power of the remote when the board is not connected (to the remote). Attention! “●” means “solid”, “ ☉”
means “flash” and “○” means “die out”.
5) Throttle/Brake Control
User can move the “throttle scroll wheel” forward to speed up, and move it backward to brake.
Notes: Do not move the “throttle scroll wheel” when pressing the Button A (/Power Switch). If you see the four LEDs (on the
remote) flash in the following way: “●○○●”, “○●●○”, “●○○●”, “○●●○”..., then please check if the “throttle
scroll wheel” is at the neutral/zero throttle position.
6) Switch of Skateboard Direction
When the board is moving forward, if the user moves the Switch C backward, the remote will vibrate a single, short vibration (0.1
second), the four LEDs will flash one by one from front to back to indicate the “Backward mode”. When the board is moving
backward, if the user moves the Switch C forward, the remote will vibrate a single, short vibration, the four LEDs will flash one by
one from back to front to indicate the “Forward mode”.
Note: this operation effects only when the “throttle scroll wheel” is at the neutral position.
7) Switch of Gears
The Button B on the remote (as shown in the picture) is for changing gears. In general, there are two gears available: 1
st
gear & 2
nd
gear or low-speed gear & high-speed gear.
When in 1
st
gear, if press the Button B, the remote will vibrate a single, short vibration, the four board power LEDs will flash one
by one (from one end to the other end) rapidly to indicate that the board is in 2
nd
gear now.
When in 2
nd
gear, if press the Button B, the remote will vibrate a single, short vibration, the four board power LEDs will flash one
by one (from one end to the other end) slowly to indicate that the board is in 1
st
gear now.
Note: this operation effects only when the “throttle scroll wheel” is at the neutral position. The specific gear and speed can be
adjusted by the specific ESC the user uses.
8) Charging
 Charging the remote: the remote vibrates once after it’s connected to a power supply via the charging cable and the remote
power LED comes on Red and turns to Green when it’s fully charged.
Note: the remote can not be used during the charging, it vibrates a single, short vibration and powers off automatically after
removing the charging cable.
Model Remote for Skateboard HW6123
Battery Voltage/Capacity
3.7V/400MAH
Charging Port
Micro USB
Charging Time
1H
Communications
2.4G
Effective Distance
40m (Open Field)
Weight
55g
Compatible with ESC(s)
ESC-Skateboard-HW9005/HW9006