User's Manual

ManualsBrandsShenzhen Fitcare Electronics ManualsElectronicsbike speed/cadence sensor

Bike Speed&Cadence

sensor

This Bike Speed&Cadence Sensor consists of a separate Cadence Sensor wired to a

Speed+Distance Sensor that has a battery hatch and a buletooth4.0 transmitter. The sensor includes

two magnets to activate the sensors and cable ties for installation.

INSTRUCTIONS

This Bike Speed&Cadence Sensor is mounted to the non-drive chainstay – the side of the

bicycle opposite from the chain.

1. Using two Cable Ties, loosely hang the Cadence Sensor (A) from the underside of

the chainstay.

2. With the bare side of the Cadence Magnet (D) placed against the backside of the crank

arm, loosely attach the Cadence Magnet to the crank arm using a Cable Tie (F).

-See picture.

3. Align the magnet so the molded ridge between

"CADENCE MAGNET" passes by the symbol "RPM"

printed. Make sure the Cadence Magnet passed

within 3/8" (10 mm) of the Cadence Sensor.

NOTE: Magnet placement on the crank arm may

depend upon the Cadence Sensor placement,

the bicycle type and/or the drive chain type.

4. Tighten the Cable Tie for the Cadence Magnet, remove

the adhesive covers on the Cadence Sensor, and tighten

its Cable Ties

NOTE: Bicycles with triple chainring cranksets and/

or S-bend chainstays may require either the Cadence

Magnet or the Cadence Sensor to be shimmed in order

to get both pieces within correct proximity.

CAUTION: Be careful not to damage the covered wire between the connected sensors.

5. Place the rubber pad (C) on the bottom of the Speed+Distance Sensor (B), and loosely attach it

Make sure the battery hatch faces away from the

wheel for easy access.

6. Remove the screw from the Spoke Magnet (E), place

the part onto a rear wheel spoke so the bare magnet

side passes within 3/8” (10 mm) of the center of the

Speed+Distance Sensor.

7. Install the screw, align the Spoke Magnet, and

tighten the screw on the spoke. Make sure that it is

still aligned with the Speed+Distance Sensor.

NOTE: Location of the Speed+Distance Sensor on the

chainstay may depend on Spoke Magnet placement,

the bicycle type, and/or the drive chain type, or the

position of the attached Cadence Sensor.

NOTE: Bicycles with triple chainring cranksets and/

or S-bend chainstays may require the canting of the

Speed+Distance Sensor toward the Spoke Magnet in

order to get both pieces within correct proximity.

CAUTION: Be

careful not to damage

the covered wire between the

connected sensors.

8. Tighten the Cable Ties for the

Speed+Distance Sensor, and trim the

ends of all the cable ties with a scissor

or diagonal cutter.

NOTE: Bicycles with triple chainring

cranksets and/or S-bend chainstays may

require the canting of the Speed+Distance

Sensor toward the Spoke Magnet in order

to get both pieces within correct proximity.

The transmitter use 1pc CR2032 3V battery. The battery already installed. The battery typically

last one year. We highly recommend that you contact the retailer or our customer service

department if you need to replace them.

1. Using a coin, twist the battery door counter clockwise until it clicks out of place.

2. Remove the old battery and insert the new battery with the +side upwards.

1. Non-rechargeable and rechargeable batteries must be disposed of properly. For this

purpose, special containers are provided for non-rechargeable and rechargeable battery

disposal at communal collection centers.

2. Batteries are extremely dangerous when swallowed! Therefore, keep batteries and small

articles away from children. If a battery has been swallowed seek immediate medical

advice.

3. The batteries supplied must not be recharged, reactivated by any other means,

dismantled, put into fire or short-circuited.

A. This device is a Bluetooth Smart and ANT+ device compatible with many smart

Phones including:

a) iPhone 4S and newer

b) New iPad and newer

c) iPad mini

d) iPod Touch5 and newer

e) GALAXY A3,A5,S4,S5,Note3,etc

f) Xperia E3,Z3,C3,T3,X8,5L.etc

B. In addition, this device is also recommended to work with the following APPs:

a) Wahoofitness

b) Strava

c) MapMyRide

* All brand names and trademarks are properties of their respective owners.

Why my App cannot connect to the Speed&Cadence sensor?

Please conf

irm the Bluetooth/ANT+ and the Speed & Cadence function in your App is open.

If you are not using an APP, please confirm the App you using can support Bluetooth

Smart/ANT+.

The Bike Speed & Cadence Sensor Bluetooth/ANT+ sync function will be automatically shut

down when there is no Bluetooth/ANT+ connection

, please rotate the crank to turn on the

sensor and launch the connection, the sensor will be on for 1 min after benign waked up, if

there is no connection from the App during the time, the sensor will go into sleep mode.

Please confirm the distances from the sensor and your mobile phone is within 2 meters.

Please check the battery installed in the sensor, exchange the battery if it

is dead.

RPM sensor

speed

transmitter

Bike Cadence Sensor

Bike Speed+

Distance

Sensor

Spoke Magnet

Rubber Pad

Cadence Magnet

BATTERIES

IMPORTANT

SUPPORTED DEVICE

TROUBLESHOOTING

9. Refer to the APP instructions to pair and calibrate it with Bike Speed&Cadence Sensor

and to display its data on the APP.

10. Periodically check the cable ties and spoke screw to make sure that they are secure.