Instruction Manual

1.
a.
b.
c.
*
INSTRUCTIONS:
Charging Mobile Devices:
Ensure that your phone or tablet supports
wireless charging.
Connect the wireless charging pad to a
USB adapter under USB Input(2). Once
connected LED Indicator will glow Green.
Ensure the power from USB adapter or
power device can reach 2A output to
charge mobile device normally.
Place the enabled device on the surface
of the wireless charging pad(1).
The LED
will turn RED to indicate that the phone
is charging.
make sure that it will be centralized from
top to bottom and left to right on the mobile
device when charging.
The phone ring can be lifted up to be used
as a stand or to hold your device in your
hand while charging. Ring can be rotated
360 degrees.
.
Wireless Charging Pad
with Phone Ring
Instruction Manual
MSL-W27Q
1 x Wireless Charging Pad
1 x Instruction Manual
USB Input: 5V/1.5A
Wireless Output: 5V/1A
1.
2.
3.
•
•
Wireless Charging Pad (Suction Pad)
USB A Input
LED Indicator
Phone Ring
What’s included:
Features:
Do not use on an aircraft or in a hospital.
To reduce the risk of injury, close
supervision is necessary when the product
is used near children.
Do not expose the device to any moisture.
Do not use the device in excess of its
output rating. Overloaded outputs above
Do not use the device if damaged or
exhibit unpredictable behavior resulting in
Do not disassemble the device. Take it to
or repair is required. Incorrect reassembly
excessive temperature. Exposure to
extreme heat may cause explosion.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
repair person using only identical
replacement parts. This will ensure that
the safety of the product is maintained.
This device is not a toy.
Do not overcharge Phone. Unit may get
hot with excessive use. Remove Phone
when it is fully charged. Never charge for
more than 7 hours at a time.
Attachments on the back of your phone
can impede the effectiveness of the
wireless charger, and lead to overheating.
Please remove attachments from the phone
before charging on this device.
SAFETY PRECAUTIONS:
Read all the instructions before using the
product.
*
FCC Statement:
***KEEP OUT OF REACH OF CHILDREN***
11
.
4.
d.
3
Note: When wireless charging, if the RED
LED indicator will flash the device is either
NOT a wireless charging device or there is
an object between the device and charging
surface interfering with the charging
*
4
1
2
MADE IN CHINA
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used inaccordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception,which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum 20cm distance between the
radiator your body: Use only the supplied antenna