Data Sheet for Product
s Industry, Inc.
Building Technologies Division
–5–
FireFinder XLS Components ─ (cont.’d)
CC-2 →Card Cage-2 Slots CC-5 →Card Cage-5 Slots
CC-5 / CC-2 Card Cages
The Models CC-5 / CC-2 card cages provide the physical
mounting location and all wiring connection points for all
fire-and-voice system options cards for the FireFinder XLS
system. Model CC-5 has five (5) slots, while Model CC-2
has two (2) slots.
All cards plugged into the CC-5 / CC-2 card cage
communicate with other FireFinder XLS modules via a
common data bus. Connectors are provided on the left and
right side of the CC-5 to connect a 60-pin cable for
communications with the FireFinder XLS operator interface,
power supplies and amplifiers modules.
Field wiring to devices and circuits terminates on the
Models CC-5 / CC-2 card cages. All cards designed for use
with the Models CC-5 / CC-2 route their field wiring
terminations to the ‘top’ of the Model CC-5 / CC-2 card
cages. These connections are all power limited. Internal
wiring connections distribute 24VDC to cards or high-level
audio signals (depending on application used) connect to
the ‘bottom’ of the Model CC-5 / CC-2 card cages. These
connections are all non-power limited.
All wiring connections to the Model CC-5 / CC-2 card cages
are to removable terminal blocks. Terminal blocks are
rated for use with wire sized 12 American Wire Gauge
(AWG) to 24AWG. Each connector is numbered to make
wiring terminations to the correct position on the
terminal block simple in order to reduce potential wiring
errors.
SCM-8 → Switch Control Module
SCM-8 Switch Control Module
The Switch Control Module (Model SCM-8) is a FireFinder
XLS-option module that provides manual control to the
Emergency Voice Evacuation System (EVAC) or manual
fire-system control. Each Model SCM-8 module provides
eight (8) momentary push-button switches and 16
light-emitting diodes (LEDs) to indicate their status.
Each switch is assigned two (2) LEDs, as well as a label
to indicate the switch's programmed usage. The label
slides behind a clear protective membrane. One set of
LEDs assigned to each switch is a dual-colored LED,
which is used to indicate what type of signal is active.
Each Model SCM-8 switch is fully programmable, and may
be used to control speaker circuits and a wide range of
general-system functions such as: All Call, All Evac,
Warden's Page, Speaker, etc. Any number of circuits may
be grouped and controlled by a single switch.
Switch usages and zone groupings are assigned using the
Zeus system software-programming software. Model
SCM-8 modules are mounted on a hinged panel, as a part
of the FireFinder XLS Command Console enclosure.
LCM-8 → LED Control Module
LCM-8 LED Control Module
The LED Control Module (Model LCM-8) is a FireFinder
XLS-option module that provides LED annunciation for
FireFinder XLS system activity. Each Model LCM-8
contains eight (8) groups of two (2) LEDs – each of which
can be assigned to desired outputs using the Zeus
system software-programming tool.
Eight (8) LEDs are dual-color capable (RED or GREEN /
flashing or steady). The remaining LEDs are AMBER
flashing or steady. A space is provided for labeling of LED
functions. The label slides behind a clear, protective
membrane. Model LCM-8 dimensions are identical to
Model SCM-8, and Model LCM-8 is mounted on the same
hinged panel, as a part of the FireFinder XLS Command
Console enclosure.
RNI → Remote Network Interface
RNI Remote Network Interface
The Remote Network Interface (Model RNI) provides a
connection point for use with equipment mounted in a
remote-lobby enclosure on the FireFinder XLS FACP.
Model RNI is used to provide additional input, output and
control features to the system remotely, via the main FACP.
These additional features may include control switches
and indicators: (Models SCM-8, LCM-8 and FCM-6),
remote-emergency paging microphones or telephones:
(Models LVM, FMT), or controls used in graphic annunciators
(Models SIM-16, OCM-16) or system-status display with the
ability to acknowledge alarms, silence audibles and
reset the system (Model SSD-C-REM).
Model RNI allows The Person Machine Interface to be
mounted in the Model REMBOX2 or Model REMBOX4
remote lobby enclosure.