MM8000 MP4.
Table of Contents About this document.........................................................................................................4 1 Safety regulations ..............................................................................................7 1.1 Country-specific standards...................................................................................7 1.2 Commissioning and testing ..................................................................................7 1.
About this document About this document Purpose This manual is intended as a guide to the installation, configuration, and operations for the MM8000 management stations that includes the MAXSYS intrusion control units. It presents the MM8000 Add-on module for the MAXSYS support.
About this document - Document Type: All - Image Type: All - Advanced search criterias: Select Brochure No. and enter the document number to search for (A6V10089056). Alternatively, select Title and enter the product name (DMS8000). 2. Click Search to start. 3. In the resulting area on the right, click on Contents link to show the list of search results. For more information such as Siemens news and announcements, visit the STEP Web portal at: https://workspace.sbt.siemens.
About this document point. Conditions that you must complete or must be met before beginning a procedure are designated with a ⊳. Results, after completing a step or at the end of the entire procedure, are designated with a ⇨. ⊳ The report you want to print is open. Bold font in a procedure indicates something you should select or type. Type F for Field panels. Click OK to save changes and close the dialog box. Menu paths are indicated in bold.
Safety regulations Country-specific standards 1 1 Safety regulations This section describes the danger levels and the relevant safety regulations applicable to the use of the products described in this manual. Please read the following work instructions as well as the preceding section About this document thoroughly before beginning any work. 1.1 Country-specific standards Siemens products are developed and produced in compliance with the relevant international and European safety standards.
2 Introduction What’s new 2 Introduction The MAXSYS is an intrusion security system based on the PC6010 control unit, which can support up to 256 zones (16 on the main board and the rest on PC6108A 8-zone expansion modules) in 32 separate areas. The user interface is based on the PC6501 panels (max 64), which can guide users through the available options according to their access level (basic, advanced, supervisor, or master).
Installation Add-on distribution package 3 3 Installation 3.1 Add-on distribution package The MM8000 software for the control unit support is distributed as an add-on package, to be installed on the stations including the Composer tool (client-only and FEP stations are therefore excluded) after the standard MM8000 Setup. The package is named MM8000 MPx.xx - System Extension N. 02 (MAXSYS Vy.yy) and is made up by an installation kit of a few files.
3 Installation Software installation 3. On the station(s) with configuration capability (Composer tool), install the add-on module [➙ 11]. 4. Update the NK8000 firmware [➙ 12]. 3.2 3.2.1 Software installation Requirements This add-on does not add any special requirements to the standard MM8000 setup.
Installation Software installation 3.2.3 3 Installing the Add-on module The following is the installation procedure for the add-on module. WARNING Add-on versions older than MP4.15 require a different installation procedure; for such cases, please refer to the add-on manual of the corresponding version. 3.2.3.1 Installation on MM8000 MP4.15 and later A specific application – the Add-on Manager – is provided starting from MM8000 MP4.15, and allows installing and updating the add-on modules.
3 Installation Communication network 3.3 Communication network The control unit is connected to the MM8000 system by means of the NK8000 network and namely via the NK82xx units. In order to communicate with the control unit, the NK82xx units should however be equipped with a new firmware that is included in the installation package as an additional component (DLL) to be added to the standard firmware file set.
Installation Communication network 3 2. Expand the Channel collection folder in: Supervision System Settings > MM8000 System > Physical configuration > Station (or FEP) > Channel collection 3. Select the NS8210 driver node and then the Download tab. Download tab 4. Select all the branches (NK82xx) in the list located in the upper part of the form. Note: In order to select multiple branches, keep the CTRL key pressed while you make your selections. See the following: Selecting the NK82xx 5.
3 Installation Communication network In a few moments, the new firmware shows in the Firmware List. The _0x suffix in the firmware name indicates the add-on index. 6. Select the new firmware version in the Firmware List. 7. Click the Download Firmware button. The download procedure starts. The new firmware is downloaded to the NK82xx units via FTP (File Transfer Protocol) services over the network. 8. Ensure that you have successfully completed all downloads.
Configuration Configuration checklist 4 4 Configuration 4.1 Configuration checklist Verify that you have satisfied the items needed in the first checklist before proceeding to the configuration checklist that follows. Items needed for configuration The intrusion system architecture: number of control units (PC6010) and interfaces (PC6442) The encryption key for the communication security (=0 if no encryption is required). The local address (1 to 32) for each control unit.
4 Configuration Configuration procedure 4.2 Configuration procedure The following are the configuration procedures for the MAXSYS control unit. Adding the folder for the MAXSYS system 1. Open the Composer project. 2. Create a folder for the control unit. Adding the main MAXSYS node (PC6442 interface) 1. Select the new folder. 2. Select the MAXSYS icon . The new node is added to the project structure.
Configuration Configuration procedure 4 Setting the MAXSYS encryption key Adding the MAXSYS control unit nodes (Panel Application) 1. Select the PC6442 Maxsys Interface node. 2. Select the MAXSYS CPU icon . The new node is added to the project structure. Note: You can customise the default name of the new node by clicking once on the name, typing a new name, and pressing Enter. Note: The local address of the unit is automatically set to the next available number from 1 to 32.
4 Configuration Configuration procedure - Look for Panel Reader export files, selecting the extension CSV in the browsing window. - In the file system, locate the CSV file. - Select the file and click Open. In a few moments, the unit structure is imported. Starting the import procedure The CSV file is unique for the entire MAXSYS system, i.e. it includes all the panels (CPU nodes) for a given interface node.
Configuration Configuration procedure 4 CSV files can be re-imported after a configuration change. Note the behaviour of the import procedure: - New objects in CSV (not configured in Composer) are added to the configuration. - Old objects in CSV (already configured in Composer) are updated. - Removed objects in CSV (configured in Composer) are removed.
4 Configuration Configuration procedure WARNING Manual configuration in Composer changes may be overwritten by subsequent import if the imported file does not include them too. Linking the Communication network 1. Open NK82xx sub-folders. Expand the NK8000 network folders until you reach the node that represents the NK882x COM port that is physically connected to the control unit. 2. Select the control unit node. 3. Drag and drop the control unit node to the network COM port.
Configuration Configuration procedure 4 WARNING The NK82xx units handle the control unit messages interpretation for MM8000. In order to do so, the NK82xx needs to be downloaded with the updated configuration of the management stations, even after a minor modification to the subsystem structures (e.g.: after having imported an updated metafile including new objects).
5 Operation 5 Operation MM8000 operations are described in the document no. A6V10062409, MM8000 Operation Manual. Specifically, the possible events related to the control units are listed in the table below. Notes: When an alarm occurs, both Area and Zone objects generate an event message. Also, the MAXSYS control unit requires that the Area gets acknowledged before resetting the alarm on the Zone.
Operation Infranet Fault: : - line fault PC6010 Main board Fault: - internal fault Zone Severe alarm Tamper: - open/short line Fault: - internal fault Exclusion: - disabled - disconnected Advisory: - bypassed Bell output Fault: - internal fault Advisory: - active - test Output, TLM Advisory: - active Backbone Fault: - connection fault Power supply Fault: - AC fault - battery fault Combus Tamper Fault: - pwr supply fault - connection fault PC6108A zone expander Tamper Fault: - pwr supp
5 Operation - fire fault - automatic off User Sev.alarm: - acc.ctrl alarm - duress alarm - off duty - partially off Anomaly: - not ready Advisory: - activation Advisory: - logged in Note: All objects can also be affected by the Maintenance event according to the MM8000 function that allows setting any part of the system tree in maintenance mode and divert the associated events into a separate list. 24 Building Technologies Fire Safety & Security Products A6V10238694_a_en 30.06.
Issued by Siemens Switzerland Ltd Infrastructure & Cities Sector Building Technologies Division International Headquarters Gubelstrasse 22 CH-6301 Zug Tel. +41 41-724 24 24 www.siemens.com/buildingtechnologies Document ID A6V10238694_a_en Edition 30.06.2013 © 2013 Copyright Siemens Switzerland Ltd Technical specifications and availability subject to change without notice.
