User Manual

ManualsBrandsSiemens ManualsOperator unitsMaster Room Unit QAX810

AP1N2723en

28.08.2007

Building Technologies

HVAC Products

723

Master Room Unit

QAX810

for RRV817 Controllers

Multifunctional digital room unit as an installer and end-user interface for use

with RRV817 temperature controllers for underfloor heating systems

Use

Room unit in combination with the RRV817 temperature controller for underfloor heat-

ing systems in:

• Apartments

• Detached houses

• Light commercial applications

• Conjunction with district heating schemes or local heat sources

Zone 1 (master zone) room unit for use with RRV817 controllers in water-based heating

plant.

Functions

• Remote control and monitoring of an RRV817 controller

• Adjustments of master zone and additional zones by installer or user

• Room temperature acquisition in the master zone

• Time switch operation

• Comfort temperature setpoint adjustment

• Energy saving temperature setpoint adjustment

• Auto timer selection

• Zone selection and settings

• Display of time of day, operating mode, temperature and setpoints for all zones

Plants

Application

Primary functions

Operator functions

Summary of content (6 pages)

PAGE 1
2 Master Room Unit 723 QAX810 for RRV817 Controllers Multifunctional digital room unit as an installer and end-user interface for use with RRV817 temperature controllers for underfloor heating systems Use Plants Room unit in combination with the RRV817 temperature controller for underfloor heating systems in: • Apartments • Detached houses • Light commercial applications • Conjunction with district heating schemes or local heat sources Application Zone 1 (master zone) room unit for use with RRV817 co
PAGE 2
Type summary Type reference QAX810 Description Master room unit Compatible with* • Zone room unit QAW810 • Temperature controller RRV817 * Not suited for use with the Desigo RX range of controllers Product documentation Document Data sheet Mounting Instructions Operating Instructions Declaration of conformity Document number N2723 M2723 B2723 T2723 Mechanical design Type of unit The QAX810 master room unit is the installer/OEM/end-user master MMI for RRV817 controllers.
PAGE 3
2 C Z1 Z2 Z3 Z4 Z5 Z6 Z7 2723Z01 1 LCD display 3 4 8 1 2 3 4 5 6 7 8 7 6 5 Actual temperature Zone indication Time display Heating ON Auto timer mode Energy saving mode Comfort mode System off Engineering notes Note on product liability • The products may only be used in building services plant and applications as described above. • When using the products, all requirements specified under ”Technical data” must be observed. • Local regulations for electrical installations must be complied with.
PAGE 4
Commissioning notes Response on startup When powering up, the QAX810 will display all LCD symbols for approximately 2 seconds. The LCD will then revert to normal display. The time segments will be flashing if time of day needs to be set. Set time of day as per Operating Instructions. There will be a delay before operation commences due to polling of all values. Sensor calibration Generally, there is no need to calibrate the sensor.
PAGE 5
Materials and colors Top housing Polycarbonate, RAL 9003 (signalwhite) Polycarbonate, RAL 7035 (lightgrey) corrugated cardboard Bottom housing and base plate Packaging Norms and standards Product safety Automatic electrical controls for household and similar use Special requirements for temperature sensing controls Electromagnetic compatibility Immunity domestic section, light industry Emissions domestic section, light industry -conformity EMC directive Low-voltage directive EN 60 730-1 EN 60 730-2-9
PAGE 6
3035M01 Dimensions 119 Controller 23,8 96 28 4 28 26 30 89,45 6/6 Siemens Building Technologies 3035M02 11,8 30 28 112,3 4 35 28 Base Dimensions in mm ©2005-2007 Siemens Switzerland Ltd Subject to alteration Master Room Unit QAX810 AP1N2723en 28.08.