User's Manual
Table Of Contents
- SIMATIC RF300
- Legal information
- Table of contents
- 1 Introduction
- 2 Safety information
- 3 System overview
- 4 Planning the RF300 system
- 4.1 Fundamentals of application planning
- 4.1.1 Selection criteria for SIMATIC RF300 components
- 4.1.2 Transmission window and read/write distance
- 4.1.3 Width of the transmission window
- 4.1.4 Impact of secondary fields
- 4.1.5 Setup help of the readers of the second generation
- 4.1.6 Permissible directions of motion of the transponder
- 4.1.7 Operation in static and dynamic mode
- 4.1.8 Dwell time of the transponder
- 4.1.9 Communication between communications module, reader and transponder
- 4.2 Field data for transponders, readers and antennas
- 4.3 Installation guidelines
- 4.4 Chemical resistance of the transponders
- 4.5 Guidelines for electromagnetic compatibility (EMC)
- 4.1 Fundamentals of application planning
Table of contents
SIMATIC RF300
8 System Manual, 07/2016, C79000-G8976-C345-0x
7.8.4.2 Temperature response in cyclic operation ........................................................................... 243
7.8.5 Use of the transponder in the Ex protection area ................................................................ 246
7.8.5.1 Use of the transponder in hazardous areas for gases ......................................................... 246
7.8.5.2 Installation and operating conditions for the hazardous area .............................................. 247
7.8.6 Cleaning the mobile data memory ....................................................................................... 247
7.8.7 Technical specifications ....................................................................................................... 247
7.8.8 Dimensional drawing ............................................................................................................ 249
8 ISO transponder .................................................................................................................................. 251
8.1 Memory configuration of ISO the transponders ................................................................... 252
8.2 MDS D100 ............................................................................................................................ 254
8.2.1 Characteristics ..................................................................................................................... 254
8.2.2 Ordering data ....................................................................................................................... 254
8.2.3 Metal-free area ..................................................................................................................... 254
8.2.4 Technical data ...................................................................................................................... 256
8.2.5 Dimension drawing .............................................................................................................. 258
8.3 MDS D117 ............................................................................................................................ 259
8.3.1 Features ............................................................................................................................... 259
8.3.2 Ordering data ....................................................................................................................... 259
8.3.3 Mounting in metal ................................................................................................................. 260
8.3.4 Technical specifications ....................................................................................................... 260
8.3.5 Dimension drawing .............................................................................................................. 261
8.4 MDS D124 ............................................................................................................................ 262
8.4.1 Characteristics ..................................................................................................................... 262
8.4.2 Ordering data ....................................................................................................................... 262
8.4.3 Mounting on metal ............................................................................................................... 263
8.4.4 Technical specifications ....................................................................................................... 264
8.4.5 Use of the MDS D124 in hazardous area ............................................................................ 265
8.4.6 Dimension drawing .............................................................................................................. 267
8.5 MDS D126 ............................................................................................................................ 268
8.5.1 Characteristics ..................................................................................................................... 268
8.5.2 Ordering data ....................................................................................................................... 268
8.5.3 Mounting on metal ...............................................................................................................
269
8.
5.4 Technical specifications ....................................................................................................... 270
8.5.5 Dimension drawing .............................................................................................................. 271
8.6 MDS D127 ............................................................................................................................ 272
8.6.1 Features ............................................................................................................................... 272
8.6.2 Ordering data ....................................................................................................................... 272
8.6.3 Mounting in metal ................................................................................................................. 273
8.6.4 Technical specifications ....................................................................................................... 274
8.6.5 Dimension drawing .............................................................................................................. 275
8.7 MDS D139 ............................................................................................................................ 276
8.7.1 Characteristics ..................................................................................................................... 276
8.7.2 Ordering data ....................................................................................................................... 277
8.7.3 Mounting on metal ............................................................................................................... 277
8.7.4 Cleaning the mobile data memory ....................................................................................... 278
8.7.5 Technical specifications ....................................................................................................... 279
8.7.6 Use of the MDS D139 in hazardous areas .......................................................................... 280
8.7.7 Dimension drawings ............................................................................................................. 282