Dishwasher SN.../SX...
6HWXS VHF Ù 5HVHW VHF
en Table of contents no i t cur t sen I l aunam 8 Intended use . . . . . . . . . . . . . . . . 5 ( Safety instructions. . . . . . . . . . . . 5 Before you switch ON the appliance . . . . . . . . . . . . Delivery. . . . . . . . . . . . . . . Installation. . . . . . . . . . . . . In daily use . . . . . . . . . . . . Damage . . . . . . . . . . . . . . Disposal . . . . . . . . . . . . . . Door lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
en 1 Operating the appliance . . . . . . 30 Programme data . . . . . . . . . . . . . . . .30 Changing the settings . . . . . . . . . . . .30 Opening the door . . . . . . . . . . . . . . .30 AquaSensor . . . . . . . . . . . . . . . . . . . .30 Time display . . . . . . . . . . . . . . . . . . .30 Sensor setting . . . . . . . . . . . . . . . . . .31 extraDry . . . . . . . . . . . . . . . . . . . . . . .31 Eco forecast . . . . . . . . . . . . . . . . . . .31 Auto Power Off . . . . . . . . . . . . . . . . .
Intended use en 8 Intended use ■ e s u dedne t n I ■ ■ This appliance is intended for use in the home and domestic environments. Use the dishwasher only in the home and only for its designated purpose: for washing domestic dishes. This appliance is intended for use up to a maximum altitude of 4000 metres above sea level.
en Safety instructions Installation ■ ■ ■ ■ ■ ■ ■ 6 Following installation, ensure that the back of the dishwasher is not freely accessible (protection against contact due to hot surface). Install and connect the appliance according to the installation and assembly instructions. Prior to installation, disconnect the dishwasher from the power supply. Ensure that the protective conductor system of the domestic supply has been correctly installed.
Safety instructions en ■ ■ ■ ■ Do not install the appliance near heat sources (radiators, heat storage tanks, cookers or other appliances which generate heat) and do not install under a hob. Please note that the insulation material of the dishwasher power cord may melt next to heat sources (e.g. heating / hot water installations) or hot appliance parts. Make sure that the power cord of the dishwasher never comes into contact with heat sources or hot appliance parts.
en Safety instructions : Warning Risk of injury! ■ To prevent injuries, e.g. caused by stumbling, open the dishwasher only briefly in order to load and unload the dishwasher. ■ Knives and other utensils with sharp points must be placed with the points downwards in the cutlery basket*1b or horizontally on the knife shelf* or in the cutlery drawer*1*. ■ Do not lean or sit on the open door. ■ In the case of free-standing appliances, ensure that the baskets are not overloaded. The appliance could tip.
Safety instructions en ■ ■ ■ Ensure that children do not place fingers in the tablet collecting tray 1B. Small fingers could become caught in the slots. When opening and closing the door on an eye-level appliance, ensure that children do not become jammed or crushed between the appliance door and the cupboard door below. Children could become locked in the appliance (danger of suffocation) or get into another dangerous situation.
en Environmental protection Deactivate the child-proof lock (door lock) as follows: 1. Press the catch of the child-proof lock to the right (1). 2. Press the catch of the child-proof lock backwards (2). The childproof lock is deactivated. 7 Environmental protection Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials. Please dispose of the individual parts separated according to type.
Getting to know your appliance en * Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found at the front of the manual. Individual positions are referred to in the text. ecna i l p a ruoy wonk o t gn i t eG Automatic door opening To open the door without using the handle, the appliance features an automatic door opening system. Press the upper middle part of the door and the appliance will open by itself.
en Getting to know your appliance Appliance interior See Fig. ~ Page 2 1" Interior light * 1* Cutlery drawer * 12 Top basket 1: Upper spray arm 1B Tablet collecting tray 1J Lower spray arm 1R Dispenser for special salt 1Z Filters 1b Cutlery basket * 1j Bottom basket 9" Dispenser for rinse aid 9* Detergent dispenser 92 Lock for detergent dispenser 9: Rating plate * depending on the features of your dishwasher Info button { The Info button { can be used to display additional programme information.
Getting to know your appliance en Switching on the appliance for the first time When the dishwasher is switched on for the first time, you are taken directly to the settings for switching on the appliance for the first time. The following text is indicated on the display window at the top @: Scroll with < > Set with - + Leave with Setup 3 sec. The required settings for switching on the appliance for the first time are listed in the table below. Change the setting as follows: 1.
en Getting to know your appliance Settings The dishwasher has been preset with certain settings for your convenience. You can change this factory setting. 4. Keep pressing button > )* until the Change the setting as follows: 1. Open the door. 2. Switch on ON/OFF switch (. 3. Press Info button { 8 for 3 seconds until the following text is indicated on the display window at the top @: Scroll with < > Set with - + Leave with Setup 3 sec. 6. Press and hold the Info button { required setting is displayed.
Getting to know your appliance en Setting Factory setting Infotext by pressing Info button { Timelight * On While programme is running, status information is projected onto floor. Infolight * On Light is projected to signal an active cleaning cycle. Start programme Eco 50° When switching on, the last selected programme appears. Tone volume * Setting 2 Volume of signal at end of programme. Button volume Setting 2 Volume when using buttons.
en Water softening system/special salt + Water softening system / special salt t l as l a i ceps /me t sys gn i ne t f os re t aW To ensure good rinsing results, the dishwasher requires soft water, i.e. water which is low in lime, otherwise limescale will be deposited on the utensils and interior container. Tap water above 7° dH (1.2 mmol/l) must be softened. The water is softened with special salt (regeneration salt) in the water softening system of the dishwasher.
Rinse aid en Top up the salt as follows: 1. Undo the screw plug on the dispenser 1R. 2. Fill the dispenser with water (required only when switching on the appliance for the first time). 3. Add salt as illustrated (do not use table salt or tablets). The water is displaced and runs out.
en Rinse aid Top up the rinse-aid as follows: 1. Open dispenser 9"; press lug on the lid (1) and lift (2). Setting amount of rinse aid The amount of rinse aid to be dispensed can be set from 0 to 6. Set the amount of rinse aid to be dispensed to 5 to obtain a very good drying result. Do not change the amount of rinse aid unless there are streaks or water stains on the utensils. Set a lower level to avoid streaks. Set a higher level to avoid water stains. Set the amount of rinse aid as follows: 2.
Utensils en - Utensils Loading the dishwasher Not suitable is not necessary to prerinse utensils under running water. 2. Place the utensils so that – they are secure and cannot tip over. – all utensils with their openings face down. – parts with curves or indentations are at an angle, thereby allowing water to drain. – does not obstruct rotation of the two spray arms 1: and 1J. s l i s ne t U Cutlery and utensils made of wood. Delicate decorative glasses, craft and antique utensils.
en Utensils Note: Utensils must not be placed above the tablet collecting tray 1B. These may block the lid of the detergent dispenser and prevent it from opening fully. Tip: Heavily soiled utensils (pans) should be placed in the lower basket. The more powerful spray jet provides a better dishwashing result. Tip: Other examples, such as the best way of loading your dishwasher, can be found on our homepage. These can be downloaded free of charge.
Utensils en You can take out the cutlery drawer. Etagere * The etagere and the space underneath can be used for small cups and glasses or for larger items of cutlery, such as wooden spoons or serving cutlery. If you do not require the etagere, it can be folded up. e r ega t E &/,&. Depending on the features of your dishwasher, you can fold down the side shelves to provide more room for taller items of cutlery. The front rows of prongs can be folded down to provide room for wider handles.
en Utensils Folding spikes * * Depending on the features of your dishwasher, the spikes can be folded down. This facilitates arrangement of pots, bowls and glasses. s e k i p s g n i d l oF Fold down the spikes as follows: 1. Press lever forwards (1). 2. Fold down spikes (2). Small items holder * * Depending on the features of your dishwasher, the upper basket is fitted with small items holders. The small items holders can be used to securely attach light plastic parts.
Utensils en Baking sheet spray head * * depending on the features of your dishwasher Large trays or grilles as well as large plates (gourmet plates, pasta plates, dinner plates) can be cleaned with this spray head. daeh yarps t e hs gn i kaB Insert the spray head as follows: 1. Remove upper basket 12. 2. Insert spray head as illustrated and turn to the right. Spray head is engaged.
en Utensils Appliance height 86.5 cm With cutlery basket Upper basket Lower basket Setting 1 max. ø 24 cm 34 cm Setting 2 max. ø 26.5 cm 30.5 cm Setting 3 max. ø 29 cm 28 cm With cutlery drawer Upper basket Lower basket Setting 1 max. ø 18 cm 34 cm Setting 2 max. ø 20.5 cm 30.5 cm Setting 3 max. ø 23 cm 28 cm Upper basket with side levers 1. Pull out upper basket 12. 2. Hold the sides of the basket along the upper edge. This prevents it from suddenly dropping. 3.
detergent en . Detergent You can use tablets as well as powder or liquid detergents for dishwashers, but never use washing-up liquid. The dosage can be individually adjusted with powder or a liquid detergent according to the degree of soiling. Tablets contain an adequately large amount of active ingredients for all cleaning tasks. Modern, powerful detergents predominantly use a low-alkaline formulation with enzymes. Enzymes break down starch and remove protein. To remove coloured stains (e.g.
en detergent Combination detergent Apart from conventional detergents (Solo), a number of products are offered with additional functions. These products contain not only the detergent but also rinse-aid and salt replacement substances (3in1) and, depending on the combination (4in1, 5in1, ...), additional components such as glass protection or stainless steel cleaner. Combination detergents function only up to a specific degree of hardness (usually 21°dH). Over this limit salt and rinse-aid must be added.
Overview of programmes en / Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
en Overview of programmes Type of utensils Type of soiling mixed utensils and cutlery part dried, common household food remnants sensitive utensils, cutlery, slightly adhesive, temperature-sens fresh food remnants itive plastic and glasses sensitive utensils, cutlery, slightly adhesive, temperature-sens fresh food remnants itive plastic and glasses all types of utensils programme Possible additional options Programme sequence intensiveZone option Half load option HygienePlus extraDry Option Shine and
Additional functions en 0 Additional functions Ï intensiveZone * Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. e n oZe v i s n e t n i * Depending on the features of your dishwasher, you can select different additional functions h.
en Operating the appliance 1 Operating the appliance Programme data ecna i l p a eh t gn i t arepO The programme data (consumption values) can be found in the summary of instructions. They refer to normal conditions and the water hardness set value °E 16 - 20 medium. Different influencing factors such as water temperature or line pressure may result in deviations. Changing the settings The dishwasher has been preset with certain settings for your convenience. You can change these factory settings.
Operating the appliance en Sensor setting The programme sequence is optmised in Auto programmes with the aid of sensors. The sensors adjust the programme strength of Auto programmes depending on the amount and type of soiling. You can adjust the sensitivity of the sensors in 3 stages. Standard: This setting is ideal for a mixed load and heavily soiled utensils, but also saves energy and water.
en Operating the appliance TimeLight (Optical display while the programme is running) * * depending on the features of your dishwasher While programme is running, an optical display (additional programme information) is indicated on the floor under the appliance door. If the base panel is pulled forwards or if the appliance is installed at eye-level with flush furniture front, the display is not visible. You can switch the optical display on or off.
Operating the appliance en Eco drying Factory setting If you have selected the Eco 50° programme, the door opens automatically when the programme ends. This ensures a particularly economical drying result. You can switch Eco drying on or off. You can reset all settings to the factory setting. Notes ■ Eco drying is activated only in conjunction with the Eco 50° programme. ■ Eco drying is deactivated when – ExtraDry is switched on.
en Operating the appliance Time preselection Switching off the appliance You can delay the start of the programme by up to 24 hours. Depending on the setting of the time display, the end of programme is indicated with “Finish in” (for example 3h 25m) or “Finish at” (for example 15:20 hours). Short time after the end of the programme: 1. Open the door. 2. Switch off ON/OFF switch (. 3. Turn off tap (does not apply to appliances with Aqua-Stop). 4. Remove the utensils when they have cooled down.
Cleaning and maintenance en Terminating the programme (Reset) 1. Open the door. 2. Press the START button )" and 2 Cleaning and maintenance emargorp eh t gn i t an imreT 3. 4. 5. 6. hold for 3 seconds The display window at the top @ and the front display * ): show: "Program was terminated". Close the door. The programme sequence lasts approx. 1 min. The display window at the top @ shows: “Finished”. Open the door. Switch off ON/OFF switch (. Close the door.
en Cleaning and maintenance Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces.
Fault, what to do? en Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1: and 1J. 1. Check outlet nozzles on the spray arms for blockages. 2. Unscrew the upper spray arm 1: (1) and remove downwards (2). 3. Remove the lower spray arm 1J upwards. 3 Fault, what to do? Experience has shown that you can rectify most faults which occur in daily operation yourself. This ensures that the appliance is quickly available to you again.
en Fault, what to do? Waste water pump 6. Check impeller wheel and remove Large food remnants or foreign objects which were not captured by the filters may block the waste water pump. The rinsing water will then be above the filter. 7. Place pump cover in the original : Warning Danger of cutting! Sharp and pointed objects or glass fragments may block the waste water pump. Always carefully remove foreign objects. Clean the waste water pump as follows: 1. Disconnect the dishwasher from the power supply.
Fault, what to do? en Fault table Fault Cause Remedial action Error code “:‚‰ is lit. Supply hose kinked. Install supply hose without kinks. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min. 10 l/min. when water supply is open. Filter in the water supply blocked. Switch off the appliance and pull out the mains plug. Turn off the tap. Unscrew water connection. Clean filter in the supply hose. Screw water connection on again. Check for leaks.
en Fault, what to do? Fault Cause Error code “:ƒ† is lit. Waste water pump blocked or Clean pump and lock cover correctly. cover on the waste water pump is ~ "Waste water pump" on page 38 not locked in position. Error code “:ƒˆ is lit. Mains voltage too low. Not an appliance fault, have the mains voltage and electrical installation checked. A different error code is indicated on the digital display. (“:‹‚ to “:„‹) A technical fault has probably occurred.
Fault, what to do? en Fault Cause Remedial action Utensils not dry. No or too little rinse aid in the dispenser. Refill rinse aid. Programme selected without drying. Select programme with drying. ~ "Overview of programmes" on page 27 Water collecting in depressions on the utensils and cutlery. Arrange utensils in a sloping position, arrange affected utensils as sloping as possible. The combined detergent used has a poor drying performance.
en Fault, what to do? Fault Cause Remedial action Food remnants on the utensils. Utensils placed too closely together, utensils basket overfilled. Arrange utensils with adequate clearance between them ensuring that the spray jets can reach the surface of the utensils. Prevent contact points. Spray arm rotation obstructed. Arrange utensils so that the spray arm can rotate without obstruction. Spray arm nozzles are blocked. Clean the spray arm nozzles.
Fault, what to do? en Fault Cause Detergent residue. Detergent dispenser cover 9* Utensils must not be placed above the blocked by utensils and therefore tablet collecting tray 1B. These may does not open fully. block the lid of the detergent dispenser and prevent it from opening fully. ~ "Upper basket" on page 19 Do not place utensils or fragrance dispenser in the tablet collecting tray. Water stains on plastic parts. Remedial action Detergent dispenser cover 9* blocked by the tablet.
en Fault, what to do? Fault Cause Remedial action White, stubborn coatings; limescale on the utensils, container or door. Detergent substances are Change detergent brand. deposited. These coatings cannot Clean appliance mechanically. usually be removed with chemicals (appliance cleaner, ...). Hardness range incorrectly set or Set water softening system according to water hardness greater than 8.9 instructions for use or top up salt. mmol/l. Tea or lipstick residue on the utensils.
Fault, what to do? en Fault Cause Remedial action Plastic parts discoloured. Too low rinsing temperature. Select programme with higher washing temperature. Utensils precleaned too intensely; sensors therefore decide on weak programme sequence. Stubborn soiling cannot be completely removed. Do not prerinse utensils. Remove only large food remnants. Increase sensitivity of the sensors. ~ "Sensor setting" on page 31 Recommended programme Eco 50° Too much rinse aid.
en Fault, what to do? Fault Cause Remedial action Appliance cannot be switched on or operated. Malfunction. Disconnect appliance from the power supply; pull out the mains plug or switch off the fuse. Wait at least 5 seconds, then connect the appliance to the power supply. Appliance does not start. The mains fuse has tripped. Check mains fuse. Power cord not inserted. Ensure that the power cord is plugged all the way into the back of the appliance and into the socket.
Fault, what to do? en Fault Cause Remedial action Door does not open. Door is not set correctly. Set the door correctly with the aid of the installation instructions. Child-proof lock is activated. Press twice in quick succession at the top of the door in the middle. Appliance is disconnected from the mains. Check mains plug and fuses. Attach supplied emergency release to upper right and left of the furniture panel and open the door by gently pulling the emergency release.
en Fault, what to do? Fault Cause Appliance stops in the Door not closed properly. programme or programme Do not place utensils or fragrance is interrupted. dispenser in the tablet collecting tray. Top basket presses against the door and prevents door from being closed securely. Power and/or water supply interrupted. Remedial action Close the door. Check whether rear panel is being pressed in, e.g. by socket or by hose holder which has not been removed. Restore power and/or water supply.
Customer service en 4 Customer service If you are unable to rectify the fault, please contact your customer service. We will always find an appropriate solution in order to avoid unnecessary visits by engineers. Contact information for your nearest customer service can be found on the back of these instructions for use or on the enclosed customer service list. When calling, please state the appliance number (E-Nr.
en Installation and connection Contents of package Delivery If you have any complaints, contact the dealer from whom you purchased the appliance or our customer services. Your dishwasher has been checked thoroughly in the factory to ensure that it is in working order. This may cause small water stains. These will disappear after the first wash cycle.
Installation and connection en Installation Drinking water connection The required installation dimensions can be found in the installation instructions. Level the appliance with the aid of the height-adjustable feet. Ensure that the appliance is situated securely on the floor. 1. Fasten the drinking water connection ■ ■ A built-under or integrated appliance which is installed subsequently as a free-standing appliance must be secured to prevent it from overturning, e.g.
en Installation and connection Warm water connection * * depending on the features of your dishwasher The dishwasher can be connected to cold or hot water up to max. 60 °C. Connection to hot water is recommended if the hot water can be supplied by energetically favourable means and from a suitable installation, e.g. solar heating system with circulation line. This will save energy and time. The “Hot water” setting allows you to adjust your dishwasher optimally to operation with hot water.
Installation and connection en Electrical connection ■ ■ ■ ■ ■ ■ Connect the appliance to an alternating current only, ranging from 220 V to 240 V and 50 Hz or 60 Hz via a correctly installed socket with protective earth conductor. See rating plate for required fusing 9:. The socket must be near the appliance and freely accessible following installation.
en Installation and connection Transporting Empty the dishwasher and secure loose parts. Drain the appliance according to the following steps: 1. Turn on the tap. 2. Open the door. 3. Switch on ON/OFF switch (. 4. Select programme with the highest temperature. The estimated programme duration is indicated on the display window at the top @. 5. Press START button )". 6. Close the door. Programme sequence starts. 7. Open the door after approx. 4 minutes. 8.
6
$48$ 6723 JXDUDQWHH HQ GRHV QRW DSSO\ WR DSSOLDQFHV ZLWKRXW $TXD 6WRS ,Q DGGLWLRQ WR ZDUUDQW\ FODLPV DJDLQVW WKH VHOOHU EDVHG RQ WKH SXUFKDVH FRQWUDFW DQG LQ DGGLWLRQ WR RXU DSSOLDQFH ZDUUDQW\ ZH ZLOO SD\ GDPDJHV XQGHU WKH IROORZLQJ FRQGLWLRQV ,I RXU $TXD 6WRS V\VWHP LV GHIHFWLYH DQG FDXVHV ZDWHU GDPDJH ZH ZLOO PDNH JRRG WKH GDPDJH IRU SULYDWH XVHUV 7R HQVXUH ZDWHU GDPDJH SURWHFWLRQ WKH DSSOLDQFH PXVW EH FRQQHFWHGWR WKH SRZHU VXSSO\ 7KLV OLDELOLW\ JXDUDQWHH LV YDOLG IRU WKH VHUYLFH OLIH R