Satellite Radio User Manual

103
Configuration Parameters
Timing Configuration
Parameter Name Description Addr
Default
Value
Type Set Value Get Value
dtmf_qual_delay
length of time dtmf tone must be detected by hardware to
be recognized
48 1 byte
C106 48 B (0…255) D C107 48 D
telemetrydelayl
time from key up to start of key up telemetry
49 8 byte
C106 49 B (0…255) D C107 49 D
xmittimeouts_long
time from key up to dropping carrier
50 40 byte
C106 50 B (0…255) D C107 50 D
xmittimeouts_short
time from key up to dropping carrier with link delay off
51 0 byte
C106 51 B (0…255) D C107 51 D
dtmftimeouts
timeout between dtmf entry to abort command entry
52 30 byte
C106 52 B (0…255) D C107 52 D
busytimeouts
dtmftimout for busy signal on case
53 60 byte
C106 53 B (0…255) D C107 53 D
id_idleto
time before ID is forced after transmit starts after long
transmit gap (repeater port)
54 30 word
C108 54 B (0…255) D C109 54 D
id_politeto
time remaining in absolute timeout when ID will be
triggered if transmit is idle (repeat port)
56 120 word
C108 56 B (0…255) D C109 56 D
id_absto
absolute timeout for sending ID (normally 10 minutes)
58 600 word
C108 58 B (0…255) D C109 58 D
id_lnkidleto
time before ID is forced after transmit starts after long
transmit gap (link port)
60 5 word
C108 60 B (0…255) D C109 60 D
cmdteldelays
delay after first command recognized until command
telemetry starts
62 15 byte
C106 62 B (0…255) D C107 62 D
serteldelays
delay after first command recognized until command
telemetry starts, with rs232 command source and
teltolocal=1. Value is 1 (defined by SERTELDELAYS0) if
teltolocal=0.
63 1 byte
C106 63 B (0…255) D C107 63 D
dialtonetimeout
timeout for dial tone after prefix recognized if not
command is entered
64 10 byte
C106 64 B (0…255) D C107 64 D
parmtimeout
timeout while waiting for a command parameter to be
entered
65 5 byte
C106 65 B (0…255) D C107 65 D
fantimeouts
timeout for fans after transmit stops
66 255 byte
C106 66 B (0…255) D C107 66 D
rcvqdelays_loc
time local receiver needs to detect COR and/or PL until
detected active, normal value
67 10 byte
C106 67 B (0…255) D C107 67 D
rcvunqdelays_loc
local receiver delay to drop receiver active, normal value
68 30 byte
C106 68 B (0…255) D C107 68 D
rcvqdelays_lnk
link receiver delay to receiver active detect, normal value
69 10 byte
C106 69 B (0…255) D C107 69 D
rcvunqdelays_lnk
link receiver delay to drop receiver active, normal value
70 1 byte
C106 70 B (0…255) D C107 70 D
rcvqdelays[]
specific radio values, set by set radio defaults
71
s
ee abov
e
byte
C106 71 B (0…255) D C107 71 D
rcvunqdelays[]
specific radio values, set by set radio defaults
79
s
ee abov
e
byte
C106 79 B (0…255) D C107 79 D
Strings
Parameter Name Description Addr
Default
Value
Type Set Value Get Value
allocated size of prefix
5
prefix_string
0 terminated string with prefix (0..9, A..B, # allowed)
87 special
allocated size of ID string
20
id_string
0 terminated string to be sent as repeater ID
92 special
id_string2
0 terminated string with alternate ID
112 special
allocated size of location string
20
loc_string
0 terminated string with location
132 special
loc_string2
0 terminated string with alternate location
152 special
idselect
OBSOLETE
172 0 byte
C
106 172 B (0…255)
D
C107 172 D