User manual
5
MOUNTING INSTRUCTIONS
1 // Before mounting, check that there are no service pipes, e.g. for electricity, gas or water, in that part of the wall.
2 // When mounting the magnetic glass board, please ensure that it does not come into contact with sharp objects or hard surfaces such
as stone or tiles. We cannot accept any claims for resulting damage to the board. Place the board on a soft surface until it is ready to be
mounted and do not remove the protective corners until it is attached to the wall.
3 // The magnetic glass board is suitable for wall-mounting only.
4 // In order to mount our magnetic glass boards correctly, we recommend using the enclosed drilling template. You will find the measure-
ments for the relevant distances between drill holes on page 10 and on our website at www.sigel.co.uk/mounting
MOUNTING
1 // The magnetic glass board can be mounted in portrait or landscape format. The enclosed drilling template makes it simple to mark the
position of the drill holes. The wall fixings
d
are screwed securely to the wall using anchors
b
and screws
c
. The side of the board with
the Sigel logo should be facing outwards (Fig. I).
Tip: Please use a spirit level to check that the wall fixings
d
are lined up straight.
The wall fixings
d
have an oblong hole that can be used to adjust their position if necessary. To do so, loosen the screw and move the wall
fixings
d
vertically or horizontally as required. Then tighten the screw again.
2 // The magnetic glass board
a
is then mounted onto the wall fixings
d
(Fig. II). There are two mounting fittings
e
on the back of the
board for this. Each mounting fitting
e
has two openings (Fig. III); the wall fixings
d
must always be slotted into the top opening rather
than the side opening, whether the board is hung in portrait or landscape format. Place the mounting fittings
e
on the back of the board
over the wall fixings
d
so that the wall fixings
d
are in the centre (Fig. III). Now slide the board downwards so that the wall fixings
d
click
into the mounting fittings
e
(Fig. IV) and the board is mounted securely.
Make sure that the magnetic glass board is always mounted on two fittings and check that the board is securely in place before letting go.
Silicon pads on the back of the board keep it steady while it is being written on.
SAFETY PRECAUTIONS
The artverum® Magnetic Glass Board is made of tempered safety glass tested to EN 12150-1.
The glass surface should be written on using only special markers for glass. The magnetic glass board can be cleaned with a damp or dry
cloth. Please do not use abrasive scouring agents, detergents or chemicals to clean the board. To prolong the life of your board, we recom-
mend using our own Sigel accessories: liquid chalk markers and microfibre cloth.
Sigel GmbH does not assume any responsibility or guarantee for boards that have been incorrectly mounted or for any resulting damage.
SAFETY
With TÜV-approved safety mounting fittings plus superb function and product quality – tested and approved by the Global Safety
Certification of the TÜV Saar branch (safety, fitness for purpose and tested safety).
GUARANTEE
* We offer a 25-year guarantee that the glass surface will remain perfect to write on and to clean. We guarantee that the magnetic glass
board will remain easy to wipe and free of smudges and other residue when using Sigel accessories and following our instructions for use.
This guarantee does not apply in cases of mistreatment, negligence, incorrect usage or other methods of utilisation that do not comply
with the enclosed instructions.
MAGNETS
As this magnetic board is made of thick glass, you will need to use the enclosed SuperDym magnets or magnets with an extra-
strong hold to attach items to it. Treat the SuperDym magnets with caution at all times and separate them by sliding them apart
sideways. Please ensure that there is a distance of at least 10 cm between any two magnets on the artverum® Magnetic Glass
Board. If used incorrectly, two or more magnets may collide unexpectedly, causing the magnets to splinter and the magnetic
coating to chip. Splinters can fly off the magnet, injuring people nearby and damaging the glass surface of the board. Careless
use can lead to fingers or skin becoming jammed between two magnets, resulting in bruising. Magnets create a strong, far-
reaching magnetic field. Among other things, they can cause damage to televisions, laptops, computer hard drives, credit cards
and EC cards, data carriers, mechanical watches, hearing aids and loudspeakers. Magnets can affect the functioning of pace-
makers and heart defibrillator implants. Magnets are not toys! Keep them away from children – small parts are a choking hazard.
Make sure that the magnets are kept out of the reach of children. Sigel cannot be held liable for any damage or injury caused by
a failure to follow these safety measures.
GB