Installation Sheet

ManualsBrandsSignature Hardware ManualsToiletsSignature Hardware 1.6 GPF Black Oak High Tank Pull Chain Water Closet with Elongated Bowl

1High Tank Pull Chain Water Closet Installation

HIGH TANK PULL CHAIN WATER CLOSET

INSTALLATION INSTRUCTIONS

Before installing, read entire High Tank Pull Chain Water Closet Installation Instructions. Observe all local building and

safety codes.

Unpack and inspect the product for any shipping damages. If you nd damages, do not install. Contact Customer

Service at 1.866.855.2284. If you need assistance or have questions while installing your water closet, contact Customer

Service.

Do not install if you are unfamiliar with installing bathroom xtures. Signature Hardware accepts no liability for any

damage to the oor, walls, plumbing or for personal injury during installation.

TOOLS AND MATERIALS:

IMPORTANT

The water closet tank should be anchored to two wall studs. If the studs in the bathroom do not line up to the mounting

location for the water closet tank, wood blocking can be installed between the studs using standard 2 x 4’s. Wood

blocking needs to be installed behind the nished wall; we recommend consulting a professional if you are unfamiliar

with this type of installation.

Because wall construction and materials vary from home to home, Signature Hardware does not provide mounting

hardware for our high tank water closets. The appropriate mounting hardware can be purchased from your local

hardware store.

For the following installation instructions for your new water closet it is assumed that any old xtures have been removed

and any repairs to the water supply and/or toilet ange have been completed.

STANDARD BOWL INSTALLATION

1. To install the toilet bowl, press the new wax ring into place on the toilet ange on the oor with the at side down and

the tapered edge up. Apply enough pressure to hold the ring in place during installation, but be careful not to press it

out of shape.

2. Install the anchor bolts through the toilet ange. The anchor bolts should be pointing upwards so that when the toilet

is placed the bolts will project through the mounting holes on the base of the toilet.

3. When the wax ring and bolts are attached, lift the toilet and align the mounting holes with the anchor bolts on the

oor for proper placement. Set the toilet down on the oor and press in place to form a tight seal with the wax ring.

Do not move the toilet after placement; this could break the watertight seal and cause leakage.

4. Thread the washers and nuts onto the anchor bolts. Before tightening washers and nuts, verify that your toilet is

level. If the toilet is not level, place a shim under the base of the toilet and adjust as necessary.

Hacksaw Phillips Screwdriver Level

Drill Adjustable Wrench

Mounting Hardware

Wooden Shim

Pencil Tubing Cutter

Summary of content (4 pages)

PAGE 1
HIGH TANK PULL CHAIN WATER CLOSET INSTALLATION INSTRUCTIONS Before installing, read entire High Tank Pull Chain Water Closet Installation Instructions. Observe all local building and safety codes. Unpack and inspect the product for any shipping damages. If you find damages, do not install. Contact Customer Service at 1.866.855.2284. If you need assistance or have questions while installing your water closet, contact Customer Service. Do not install if you are unfamiliar with installing bathroom fixtures.
PAGE 2
5. When the toilet is properly aligned, finish tightening the washers and nuts onto the anchor bolts with an adjustable wrench. Do this gradually, alternating from one bolt to the other until both are tight. Be sure not to over tighten, as this could cause cracks and damage the base of the toilet. 6. Place the bolt caps over the anchor bolts on the base of the toilet. If the anchor bolts extend too far over the top of the washers and nuts, use a hacksaw to trim to the correct length. 7.
PAGE 3
TRIM KIT AND TANK INSTALLATION A1 1. Because the trim kit arrives assembled, it is necessary to remove the wing nuts and metal washers from the bolts on the bottom of the kit (A2). Insert the bolts through the holes in the back of the toilet bowl to fasten the trim kit to the top of the toilet bowl. Thread the washers and wing nuts onto the bolts from underneath the toilet (A2) and tighten to secure. A2 2. Remove the decorative nut and washer from the top of the trim kit (A1). 3.
PAGE 4
13. Connect the flexible water supply tube (E1) to the shut off valve (E5). 14. Connect the water line pipe (C2) to the flexible water supply tube (E1) with the compression tube fitting (E2). 15. Insert the water line pipe (C2) into the tank and tighten the nut (B3) to secure. Trim the pipe to the appropriate length if necessary. 16. In the desired location, install the water line brackets (F) over the water line pipe to hold the pipe in place after installation. E2 E2 E3 E1 E4 E5 17.