SX-SDCAG 802.
© 2010 Silex Technology America, Inc. All rights reserved. February 2010 Silex Technology America SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS OF THIS PRODUCT FOR A PARTICULAR PURPOSE. Silex shall not be liable for any errors contained in this manual or for any damages resulting from loss of use, data, profits, or any incidental or consequential damages arising from the use of SILEX products or services.
Contents About This User Manual ............................................................................................................................................ 2 Safety Precautions................................................................................................................................................. 2 Emissions Disclaimer.............................................................................................................................................
About This User Manual This user manual provides detailed specifications, diagrams and additional information required to install the SXSDCAG 802.11a/b/g SDIO module into a product. The intended audiences are the developers and engineers responsible for the integration of the module in another product. Safety Precautions To prevent damage to the SX-SDCAG module’s electronic circuit components, follow established ESD practices and procedures for handling static-sensitive devices.
Chapter 1: Introduction The SX-SDCAG is an 802.11a/b/g radio/baseband module in a standard SDIO form factor. Designed for wireless local area network (WLAN) applications that require low power consumption, the SX-SDCAG is ideal for battery-operated portable devices in the medical, weights and measures, transportation and other industries. SX-SDCAG features include: • Highly Integrated System for 802.11a/b/g WLAN • U.
Chapter 2 Hardware Specifications/Compliance FCC Information FCC ID: N6C-SXSDCAG NOTICE In accordance with FCC Part 15, the SX-SDCAG is listed as a Modular Transmitter device. End products that include the SX-SDCAG shall have the words “Contains Transmitter module FCC ID: N6CSXSDCAG” on an exterior label. This equipment complies with Part 15 of the FCC Rules.
The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects.
safe. Low power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research.
Specifications Operating environment: Storage environment: Supply voltage: Host interface: IEEE 802.11b IEEE 802.11g IEEE 802.11a Specifications/Compliance 140-00197-100 Temperature: -20º to +70ºC (-4º to +158ºF) Humidity: 20% to 80% Temperature: -30º to +85ºC (-22º to +185ºF) Humidity: 20% to 85% 3.
Chapter 3 Installation Installation Requirements The SX-SDCAG must be installed in a device that contains a 9-pin SDIO slot. The SX-SDCAG has FCC limited single modular approval, which can eliminate the need for you to obtain FCC Part 15 Subpart C and E (intentional radiation) approvals for your device. In order to use this FCC/IC limited single modular approval for the SX-SDCAG, OEM integrators must: 1. include “Contains FCC ID: N6C-SXSDCAG, IC: 4908B-SXSDCAG” on the exterior label of your device. 2.
2. Connect one end of the antenna cable to the main antenna connector on the SX-SDCAG (see figure 2). If you are using a diversity antenna configuration, connect one end of the second antenna cable to the secondary antenna on the SX-SDCAG. Figure 2. Connecting the Antenna(s) and cable(s) to the SX-SDCAG 3. Insert the SX-SDCAG into an available SDIO slot in your device. Make sure that it is securely seated. 4.
Appendix A Antenna Information Antenna Specifications Please refer to the Ethertronics website @ www.ethertronics.com for more detailed information for the Prestta WLAN Embedded Antenna, Part No. 1000418. Table 1 Electrical Specifications Parameter Antenna Information 140-00197-100 Value Antenna Type Isolated Magnetic Dipole Frequency Range 2.4 to 5.8 GHz Impedance 50 Ohms Gain (peak) 2.4 GHz = 2.5 dBi 5.8 GHz = 3.5 dBi VSWR ≤ 2.0 Standard Connector U.
Please refer to the Pulse website @ www.pulseeng.com/antennas for more detailed information for the Pulse Dualband WLAN Ceramic Antenna, Part No. W3006. Table 2 Electrical Specifications Parameter Antenna Information 140-00197-100 Value Antenna Type High-Dielectric Monopole Frequency Range 2.4 to 5.8 GHz Impedance 50 Ohms Gain (peak) 2.4 GHz = 3.2 dBi 5.8 GHz = 4.2 dBi VSWR ≤ 2.0 Standard Connector U.
Appendix B Silex Contact Information Silex Technology America, Inc. www.silexamerica.com Technical Support: support@silexamerica.com Sales: sales@silexamerica.com Tel: (801) 748-1199 8:00 to 5:00 Mountain Time Tel: (866) 765-8761 toll-free Fax: (801) 748-0730 Silex Technology Europe GmbH www.silexeurope.com Tel: +49-2159-67500 Tel: 0800-7453938 German toll free Email: contact@silexeurope.com Silex Technology Beijing, Inc. www.silex.com.cn Tel: +86-10-8497-1430 Email: contact@silex.com.
