Instruction manual
Table Of Contents
- SIMRAD AP35 AUTOPILOT
- DOCUMENT HISTORY
- 1 GENERAL INFORMATION
- 2 OPERATION OF THE AUTOPILOT
- 2.1 Overview
- 2.2 ON/OFF - Standby mode
- Follow-Up steering
- 2.4 Non-Follow-Up steering
- 2.5 NFU Steering lever
- 2.6 NFU Push button remote control
- 2.7 R3000X Remote Control
- 2.8 S35 NFU Steering Lever
- 2.9 Automatic Steering
- 2.10 Automatic Speed selection
- 2.11 Manual speed selection
- 2.12 Navigating with the AP35
- 2.13 WORK-mode
- 2.14 TURN-mode
- 2.15 Dodging
- 2.16 Multiple station system
- 2.17 Lock function
- 2.18 User Set-up Menu
- 3 TECHNICAL SPECIFICATIONS
- 3.1 AP35 Autopilot System
- 3.2 AP35 Control Unit
- 3.3 Junction units
- 3.4 RFC35 Fluxgate compass
- 3.5 RC25 Rate Compass
- 3.6 CDI35 Course Detector Interface
- 3.7 RI35 Mk2 Rudder Angle Indicator
- 3.8 RF300 Rudder Feedback Unit
- 3.9 RF45X Rudder Feedback Unit
- 3.10 R3000X Remote
- 3.11 GI51 Gyro Interface
- 3.12 NI300X NMEA Interface
- 3.13 S35 NFU Steering Lever
- 3.14 FU50 Steering Lever
- 3.15 IP protection
- 4 INSTALLATION
- 4.1 General
- 4.2 Installation checklist
- 4.3 Unpacking and handling
- 4.4 Determine system configuration
- 4.5 AP35 System Layout
- 4.6 RF300 Rudder feedback
- 4.7 RF45X Rudder Feedback Unit
- 4.8 Junction unit
- 4.9 Drive unit
- 4.10 Control unit
- 4.11 RFC35 Fluxgate Compass
- 4.12 RC25 Rate Compass
- 4.13 R3000X Remote Control
- 4.14 FU50 Steering Lever
- 4.15 S35 NFU Steering Lever
- 4.16 F1/2 Remote Control
- 4.17 RI35 Mk2 Rudder Angle Indicator
- 4.18 Interfacing
- 4.19 Single NMEA input/output
- 4.20 Double NMEA input/output
- 4.21 Additional NMEA output on Port 2
- 4.22 Input from “NMEA Compass”
- 4.23 Radar Clock/Data
- 4.24 IS15 Instrument
- 4.25 Analog Repeater
- 4.26 Digital Repeater
- 4.27 External Alarm
- 4.28 NI300X NMEA Interface Unit
- 4.29 CI300X Compass Interface
- 4.30 GI51 Gyro Interface
- 4.31 CD100A Course Detector
- 4.32 CDI35 Interface
- 4.33 Software Setup Procedure
- 4.34 Sea Trial
- 4.35 Final sea trial
- 4.36 Providing user training
- 5 MAINTENANCE
- 6 TROUBLE SHOOTING
- 7 SPARE PARTS LIST
Operation
22083083J 15
2.3 Follow-Up steering
When both the PORT and STBD push buttons are pressed simultaneously
the AP35 is set to Follow-Up steering mode and rudder commands can be set
by the course dial. One revolution of the dial equals 45° rudder command.
The rudder will move to the commanded angle and stop.
Press both buttons
simultaneously to
activate Follow-Up
FU
22
12
STBD
PORT
Follow-Up mode.
Commanded rudder angle:
22° to stbd.
Rudder angle:12
P
S
Use course knob to
command rudder angle.
STBY
OFF
Return to manual control in
STBY by pressing the
STBY button.
WARNING ! While in Follow-Up mode, you cannot take manual control of the
vessel.
2.4 Non-Follow-Up steering
In STBY mode, when the PORT or STBD push button is pressed separately,
the actual rudder angle is shown on the secondary display and the rudder will
move as long as the button is pressed.
03
NFU
Activates
PORT
Rudder
command
05
NFU
Actual rudder angle
PORT
STBD
Activates
STBD
Rudder
command
Actual rudder angle
2.5 NFU Steering lever
In STBY mode the rudder will move as long as the lever is offset to Port or
Starboard
2.6 NFU Push button remote control
In STBY mode the rudder will move as long as the Port or Starboard button
is pressed.
Note ! When a NFU steering lever or remote control is operated, the control unit(s)
become "Inactive".