Instruction manual
Table Of Contents
- SIMRAD AP35 AUTOPILOT
- DOCUMENT HISTORY
- 1 GENERAL INFORMATION
- 2 OPERATION OF THE AUTOPILOT
- 2.1 Overview
- 2.2 ON/OFF - Standby mode
- Follow-Up steering
- 2.4 Non-Follow-Up steering
- 2.5 NFU Steering lever
- 2.6 NFU Push button remote control
- 2.7 R3000X Remote Control
- 2.8 S35 NFU Steering Lever
- 2.9 Automatic Steering
- 2.10 Automatic Speed selection
- 2.11 Manual speed selection
- 2.12 Navigating with the AP35
- 2.13 WORK-mode
- 2.14 TURN-mode
- 2.15 Dodging
- 2.16 Multiple station system
- 2.17 Lock function
- 2.18 User Set-up Menu
- 3 TECHNICAL SPECIFICATIONS
- 3.1 AP35 Autopilot System
- 3.2 AP35 Control Unit
- 3.3 Junction units
- 3.4 RFC35 Fluxgate compass
- 3.5 RC25 Rate Compass
- 3.6 CDI35 Course Detector Interface
- 3.7 RI35 Mk2 Rudder Angle Indicator
- 3.8 RF300 Rudder Feedback Unit
- 3.9 RF45X Rudder Feedback Unit
- 3.10 R3000X Remote
- 3.11 GI51 Gyro Interface
- 3.12 NI300X NMEA Interface
- 3.13 S35 NFU Steering Lever
- 3.14 FU50 Steering Lever
- 3.15 IP protection
- 4 INSTALLATION
- 4.1 General
- 4.2 Installation checklist
- 4.3 Unpacking and handling
- 4.4 Determine system configuration
- 4.5 AP35 System Layout
- 4.6 RF300 Rudder feedback
- 4.7 RF45X Rudder Feedback Unit
- 4.8 Junction unit
- 4.9 Drive unit
- 4.10 Control unit
- 4.11 RFC35 Fluxgate Compass
- 4.12 RC25 Rate Compass
- 4.13 R3000X Remote Control
- 4.14 FU50 Steering Lever
- 4.15 S35 NFU Steering Lever
- 4.16 F1/2 Remote Control
- 4.17 RI35 Mk2 Rudder Angle Indicator
- 4.18 Interfacing
- 4.19 Single NMEA input/output
- 4.20 Double NMEA input/output
- 4.21 Additional NMEA output on Port 2
- 4.22 Input from “NMEA Compass”
- 4.23 Radar Clock/Data
- 4.24 IS15 Instrument
- 4.25 Analog Repeater
- 4.26 Digital Repeater
- 4.27 External Alarm
- 4.28 NI300X NMEA Interface Unit
- 4.29 CI300X Compass Interface
- 4.30 GI51 Gyro Interface
- 4.31 CD100A Course Detector
- 4.32 CDI35 Interface
- 4.33 Software Setup Procedure
- 4.34 Sea Trial
- 4.35 Final sea trial
- 4.36 Providing user training
- 5 MAINTENANCE
- 6 TROUBLE SHOOTING
- 7 SPARE PARTS LIST
Simrad AP35 Autopilot
18 22083083K
2.10 Automatic Speed selection
The AP35 provides two different sets of steering parameters for controlling
the response of the boat at different speeds (HI or LO) while in AUTO and
NAV modes.
The AP35 always selects the HI speed steering parameters when first
switched on. This is a safety feature. After initial turn on, selection of the
steering parameters is done automatically, based on the availability of input
data from either an external speed log or an external navigator, or manually.
The AP35 automatically selects the HI or LO parameter set. The speed at
which the AP35 changes from HI to LO (or opposite) is determined by the
"Transition Speed" set in the Installation Setup Menu.
26
24
22
20
18
16
14
12
10
8
6
4
2
0
H
I
s
p
e
e
d
p
a
r
a
m
e
te
r
s
L
O
s
p
e
e
d
p
a
r
a
m
e
t
e
r
s
Transition Speed set to 9 Knots
Example of
Transition speeds with
AUTOMATIC Speed parameter
selection
Transition to HI parameters
with increasing speed: 10 Knots
Transition to LO parameters
with decreasing speed: 8 Knots
2.11 Manual speed selection
Select AUTO mode. To toggle between HI and LO speed parameters, press
the "AUTO" button two times quickly (Double click).
If you change boat speed it is recommended that you select HI or LO
parameters correspondingly.
setting
HI
AUTO
SPEED
setting
LO
The manually selected steering parameter set (HI or LO) will remain in
effect until you re-enter AUTO mode or restarts.