Instruction manual
Table Of Contents
- SIMRAD AP35 AUTOPILOT
- DOCUMENT HISTORY
- 1 GENERAL INFORMATION
- 2 OPERATION OF THE AUTOPILOT
- 2.1 Overview
- 2.2 ON/OFF - Standby mode
- Follow-Up steering
- 2.4 Non-Follow-Up steering
- 2.5 NFU Steering lever
- 2.6 NFU Push button remote control
- 2.7 R3000X Remote Control
- 2.8 S35 NFU Steering Lever
- 2.9 Automatic Steering
- 2.10 Automatic Speed selection
- 2.11 Manual speed selection
- 2.12 Navigating with the AP35
- 2.13 WORK-mode
- 2.14 TURN-mode
- 2.15 Dodging
- 2.16 Multiple station system
- 2.17 Lock function
- 2.18 User Set-up Menu
- 3 TECHNICAL SPECIFICATIONS
- 3.1 AP35 Autopilot System
- 3.2 AP35 Control Unit
- 3.3 Junction units
- 3.4 RFC35 Fluxgate compass
- 3.5 RC25 Rate Compass
- 3.6 CDI35 Course Detector Interface
- 3.7 RI35 Mk2 Rudder Angle Indicator
- 3.8 RF300 Rudder Feedback Unit
- 3.9 RF45X Rudder Feedback Unit
- 3.10 R3000X Remote
- 3.11 GI51 Gyro Interface
- 3.12 NI300X NMEA Interface
- 3.13 S35 NFU Steering Lever
- 3.14 FU50 Steering Lever
- 3.15 IP protection
- 4 INSTALLATION
- 4.1 General
- 4.2 Installation checklist
- 4.3 Unpacking and handling
- 4.4 Determine system configuration
- 4.5 AP35 System Layout
- 4.6 RF300 Rudder feedback
- 4.7 RF45X Rudder Feedback Unit
- 4.8 Junction unit
- 4.9 Drive unit
- 4.10 Control unit
- 4.11 RFC35 Fluxgate Compass
- 4.12 RC25 Rate Compass
- 4.13 R3000X Remote Control
- 4.14 FU50 Steering Lever
- 4.15 S35 NFU Steering Lever
- 4.16 F1/2 Remote Control
- 4.17 RI35 Mk2 Rudder Angle Indicator
- 4.18 Interfacing
- 4.19 Single NMEA input/output
- 4.20 Double NMEA input/output
- 4.21 Additional NMEA output on Port 2
- 4.22 Input from “NMEA Compass”
- 4.23 Radar Clock/Data
- 4.24 IS15 Instrument
- 4.25 Analog Repeater
- 4.26 Digital Repeater
- 4.27 External Alarm
- 4.28 NI300X NMEA Interface Unit
- 4.29 CI300X Compass Interface
- 4.30 GI51 Gyro Interface
- 4.31 CD100A Course Detector
- 4.32 CDI35 Interface
- 4.33 Software Setup Procedure
- 4.34 Sea Trial
- 4.35 Final sea trial
- 4.36 Providing user training
- 5 MAINTENANCE
- 6 TROUBLE SHOOTING
- 7 SPARE PARTS LIST
Simrad AP35 Autopilot
42 22083083K
c) Compass Offset adjustment
d) Automatic tuning (Optional: does not need to be done)
e) Viewing parameters
10. Testing Autopilot Operation at Sea (refer to Sea Trial instructions, page
86)
11. Provide the user with training (Page
87)
4.3 Unpacking and handling
Care should be taken when unpacking and handling the equipment. A visual
inspection should be made to see that the equipment has not been damaged
during shipment and that all components and parts are present according to
the packing list.
A standard scope of supply for an AP35 system will include:
• Control unit with standard installation accessories.
• Junction unit (J300X, J300X-40, J3000X) and one 15 m (49') Robnet
cable.
• RFC35 Fluxgate Compass with 15 m (49') cable attached.
• RF300 Feedback unit with 10 m (33') cable attached and transmission
rod.
• Appropriate drive unit for the installation (unless the AP35 is going to
operate an existing drive unit)
• Optional equipment that may have been ordered for the installation.
4.4 Determine system configuration
It is important to become familiar with the configuration of the system prior
to beginning the installation. The AP35 Basic system is shown in
Figure 4-1.
Pay particular attention to the junction unit/drive unit combinations on page
49 and the chart on page 9.
As many of the units are communicating on a common network (ROBNET),
with identical connectors, the installation is simplified. Try to mount the
units within the standard cable length supplied with each unit, if possible.
ROBNET Extension Cable (10m) is available from your distributor.