Instruction manual
Table Of Contents
- SIMRAD AP35 AUTOPILOT
- DOCUMENT HISTORY
- 1 GENERAL INFORMATION
- 2 OPERATION OF THE AUTOPILOT
- 2.1 Overview
- 2.2 ON/OFF - Standby mode
- Follow-Up steering
- 2.4 Non-Follow-Up steering
- 2.5 NFU Steering lever
- 2.6 NFU Push button remote control
- 2.7 R3000X Remote Control
- 2.8 S35 NFU Steering Lever
- 2.9 Automatic Steering
- 2.10 Automatic Speed selection
- 2.11 Manual speed selection
- 2.12 Navigating with the AP35
- 2.13 WORK-mode
- 2.14 TURN-mode
- 2.15 Dodging
- 2.16 Multiple station system
- 2.17 Lock function
- 2.18 User Set-up Menu
- 3 TECHNICAL SPECIFICATIONS
- 3.1 AP35 Autopilot System
- 3.2 AP35 Control Unit
- 3.3 Junction units
- 3.4 RFC35 Fluxgate compass
- 3.5 RC25 Rate Compass
- 3.6 CDI35 Course Detector Interface
- 3.7 RI35 Mk2 Rudder Angle Indicator
- 3.8 RF300 Rudder Feedback Unit
- 3.9 RF45X Rudder Feedback Unit
- 3.10 R3000X Remote
- 3.11 GI51 Gyro Interface
- 3.12 NI300X NMEA Interface
- 3.13 S35 NFU Steering Lever
- 3.14 FU50 Steering Lever
- 3.15 IP protection
- 4 INSTALLATION
- 4.1 General
- 4.2 Installation checklist
- 4.3 Unpacking and handling
- 4.4 Determine system configuration
- 4.5 AP35 System Layout
- 4.6 RF300 Rudder feedback
- 4.7 RF45X Rudder Feedback Unit
- 4.8 Junction unit
- 4.9 Drive unit
- 4.10 Control unit
- 4.11 RFC35 Fluxgate Compass
- 4.12 RC25 Rate Compass
- 4.13 R3000X Remote Control
- 4.14 FU50 Steering Lever
- 4.15 S35 NFU Steering Lever
- 4.16 F1/2 Remote Control
- 4.17 RI35 Mk2 Rudder Angle Indicator
- 4.18 Interfacing
- 4.19 Single NMEA input/output
- 4.20 Double NMEA input/output
- 4.21 Additional NMEA output on Port 2
- 4.22 Input from “NMEA Compass”
- 4.23 Radar Clock/Data
- 4.24 IS15 Instrument
- 4.25 Analog Repeater
- 4.26 Digital Repeater
- 4.27 External Alarm
- 4.28 NI300X NMEA Interface Unit
- 4.29 CI300X Compass Interface
- 4.30 GI51 Gyro Interface
- 4.31 CD100A Course Detector
- 4.32 CDI35 Interface
- 4.33 Software Setup Procedure
- 4.34 Sea Trial
- 4.35 Final sea trial
- 4.36 Providing user training
- 5 MAINTENANCE
- 6 TROUBLE SHOOTING
- 7 SPARE PARTS LIST
Simrad AP35 Autopilot
70 22083083K
On new installations, and whenever a control unit, junction unit, or software
is replaced in an AP35 system, it is recommended that a MASTER RESET
be performed as described in the ISM prior to proceeding with the setup
procedure.
When using the ISM refer to diagram "Installation settings Menu Flow
Chart" on next page.
DOCKSIDE
SETTINGS?
LANGUAGE ?
INTERFACE
SETUP?
SEA-TRIAL
SETTINGS?
INSTALLATION
MENU
SET RUDDER ZERO ?
RFC COMP. CALIBRATION ?
COMPASS OFFSET
AUTOMATIC TUNING ?
GPS 1
GPS 2
LC 1
LC 2
NAV 1
NAV 2
INSTR
RFC
MAGN
FLUXG.
GYRO
NMEA
INSTR
RADAR: Anritsu
Furuno
BOAT TYPE
DRIVE UNIT VOLTAGE
RUDDER FEEDBACK CALIBRATION ?
TURN RUDDER MAX STBD
TURN RUDDER MAX PORT
AUTOMATIC RUDDER TEST ?
TRANSITION SPEED
AUTOTRIM WORK
INITIAL RUDDER
MASTER RESET OF MEMORIES ?
SEA-TRIAL ITEMS
INTERFACE ITEMS
DOCKSIDE ITEMS
ENGLISH
NORSK
FRANCAIS
ESPANOL
ITALIANO
NEDERLANDS
SVENSKA
DEUTSCH
LANGUAGE ITEMS
ENTER INSTALLATION SETTINGS MENU BY PRESSING
AND HOLDING THE NAV BUTTON FOR 5 SECONDS
ENGLISH
SOFTWARE
PROGRAM
DATE
VIEW
PARAMETERS ?
RUDDER LO
CONT. RUDD. LO
AUTOTRIM LO
RUDD. LIM LO
RUDDER HI
CONT RUDD. HI
AUTOTRIM HI
RUDD LIM. HI
RUDDER WORK
PARAMETER ITEMS
Not e:
Dockside, Interface
and Seatrial Menus accessible
only in STBY mode
Mode in
STBY ?
YesNo
Output:
Input:
STBD
STBD
STBD
SELECT OR CONFIRM BY
ROTARY COURSE SELECTOR
GO TO NEXT MENU ITEM
BY PRESSING STBD BUTTON
REVERT TO PREVIOUS
MENU ITEM
SYMBOLS
PORT
STBD
STBD
STBD
Figure 4-34 Installation settings menu