MANUAL Simrad WR20 RemoteCommander Jun06 E04921 Rev.
MANUAL Simrad WR20 RemoteCommander Jun06 E04921 Rev.
WR20 Remote Commander © 2006 Simrad Ltd The technical data, information and illustrations contained in this publication were to the best of our knowledge correct at the time of going to print. We reserve the right to change specifications, equipment, installation and maintenance instructions without notice as part of our policy of continuous development and improvement.
Contents WR20 RemoteCommander 1 INTRODUCTION 1.1 1.2 1.3 1.4 CONTENTS General ................................................................................ About this manual ................................................................ SimNet network system ....................................................... Bluetooth ............................................................................. 9 10 10 10 2 INSTALLATION 2.1 2.2 2.3 2.4 2.5 General ..........................................
WR20 Remote Commander 4.2.2 4.2.3 4.2.4 4.2.5 4.2.6 4.2.1.1 Light level ............................................. 24 4.2.1.2 Color ...................................................... 25 4.2.1.3 Timeout (Lights) ................................... 25 4.2.1.4 LCD contrast ........................................ 25 4.2.1.5 KeyLock ................................................ 25 4.2.1.6 KeyBeep ................................................ 25 Unit selection ...................................
Contents 6.8.1 Tack/Gybe mode ................................................... 6.9 Autopilot alarms ................................................................. 6.9.1 WR20 Alarm Displays ........................................ 6.9.2 Volvo IPS Override Warning .............................. 39 40 40 41 7 VHF RADIO/INTERCOM 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 General ................................................................................. 43 Display .........................................
WR20 Remote Commander 11.2 Display ............................................................................... 11.2.1 ............................................................................... 11.3 Configuring DataPages ..................................................... 11.3.1 Adding DataPage items ...................................... 11.3.2 Exchanging DataPage items ............................... 11.3.3 Removing DataPage items .................................. 11.
Introduction 1.1 General The WR20 Remote Commander is a sophisticated wireless command centre comprising a rugged, compact, Handset and SimNet Base Station. It enables you to remotely control all of your SimNet electronics such as Plotter/Radar, Autopilots and Instruments. It also controls the VHF with the advanced features of voice calls. When paired to a mobile phone it offers the same operating features as a Bluetooth Handset.
Introduction WR20 Remote Commander Note The way that Bluetooth operates means that the maximum distance between the WR20 handset and its base station is less when using the handset in audio mode (VHF, intercom or mobile phone modes) than for data communication. In addition the Bluetooth signal strength is heavily attenuated by the human head and is optimized when the handset is in line of sight of the base station Fig. 1.2 Showing possible reduction in range depending on how the handset is held 1.
Introduction Warning This equipment communicates wirelessly with the installed instrument system. It is possible that the wireless link will fail due to a variety of reasons including, but not limited to, low battery power, travelling out of communication range and high levels of RF interference. Users should be aware that failure of the wireless link would lead to the inability to control the vessels systems from the WR20 including an inability to alter pilot course or make VHF calls.
Installation 2 INSTALLATION 2.1 General Installation There is no installation required for the Handset which is already “paired” to the Basestation and ready to use. Installation of the Basestation and recharge cradle is very simple. 2.2 Installing the recharge cradle Choose a convenient, dry location to mount the Handset cradle using the two screws provided. A 12V power cable is supplied and this should be connected to a suitable supply fused at 2A.
Installation WR20 Remote Commander • Avoid installing behind other electrical and electronic devices as they may reduce the signal strength and consistency of wireless communications • The Basestation should be at least 2m away from any other Bluetooth or Wireless LAN (WiFi) transceiver • Carbon fibre and steel are strong reflectors of RF signals; they can severely limit the Bluetooth range depending on the relative position of the Handset and Basestation • Mount in an accessible location for acces
Installation Fig. 2.2 - Terminal wiring Terminal Number 1 2 3 4 5 6 7 8 Wire Colour(s) Brown Green Red White Blue Yellow Orange Black The radio can also be fitted with a Simrad LS80 external speaker or third party speakers with an impedance of 4 Ohms. If an external speaker is to be fitted this must be wired directly into the connector block. Remove the wires from the connector block terminals 7 and 8 and insulate the bare ends. These wires are are redundant and not used.
Handset & Keypad Overview 3 HANDSET AND KEYPAD OVERVIEW 3.1 Layout N P Q R S T U V NM Note Handset & Keypad Overview O Functions: 1 Speaker/Earpiece 2 PTT (Push-To-Talk) 3 MOB & Soft key 1 4 MOB & Soft key 2 5 4-way NavPad (Up/Down/Left/Right) 6 Product Selection 7 Menu/Enter 8 PoWER & LIGHTS 9 STANDBY/AUTO 10 Microphone Fig 3.1 - Wireless Remote Commander When using your WR20 Handset for voice communication, hold the Handset speaker close to your ear as you would a mobile phone. 3.
WR20 Remote Commander If the PWR/LIGHTS key is released at any time during the power down sequence, the Handset will revert to whatever it was displaying prior to pressing the PWR/LIGHTS key. Handset & Keypad Overview 3.3 PTT key The PTT key (Fig. 3.1 Item 2) is reserved for the operation of the VHF Radio/Intercom (if connected). When pressed the user is able to Transmit audio from the Handset. When released the user is able to hear any audio received by the VHF Radio, (as long as the squelch is open).
Handset & Keypad Overview 3.5.2 4-Way remote key control Pressing a key on the NavPad has the same effect as pressing a specified key on the device being controlled and may be considered a Remote Key Press. 3.6 MENU key (Enter/menu key) The MENU key (Fig. 3.1 Item 7), has two functions : 3.6.1 Menu function Pressing the MENU key will bring up the menu associated with the product that is currently selected on the WR20. 3.6.
WR20 Remote Commander 3.9 PWR/LIGHTS key (Backlight adjustment) Handset & Keypad Overview The backlighting will come on whenever a key is pressed, and will stay on for 10 seconds. There are two methods for changing the level of the backlight: 3.9.1 Method one Press the PWR/LIGHTS key (Fig. 3.1 Item 8) and by using the VW keys, adjust the light to the required level. The current value will be shown in the display, (between Off - 9).
Handset & Keypad Overview Note While unlocked, every key press will reset the countdown timer to the delay value as defined in “WR20 setup”. 3.11 Battery level indicator Handset & Keypad Overview The battery charge status is indicated by the “ F ” symbol in the centre lower part of the display. When fully charged the bargraph contains the letter “F”. When the battery is depleted and requires recharging the following message (Fig. 3.2) is displayed. t~êåáåÖ _~ííÉêó içï `Ü~êÖÉ e~åÇëÉí Fig. 3.
Handset Configuration 4 HANDSET CONFIGURATION 4.1 General The WR20 has many advanced features that are user configurable as described below. 4.2 Setup options To access the setup options first press the PRODUCT key and the product list will be displayed (Fig. 4.1). pÉäÉÅí==mêçÇìÅí Handset Configuration W ^mORJN=^ìíçéáäKK opUMJO=`ä~ëë=a a~í~m~ÖÉë toOM=pÉíìé W F Fig. 4.1 - Instrument menu Using the V or W keys, highlight “WR20 Setup” and press MENU key to select it (Fig. 4.2).
WR20 Remote Commander Once selected the full list includes: • • • • • • Handset Configuration Note User settings Unit Selection Installation Phone Setup Radio Setup Select Radio “Select Radio” will only appear if more than one VHF radio is present on the SimNet network. 4.2.1 User settings Selecting the “User Settings” option from the Setup list opens the following menu (Fig.4.3). rëÉê==pÉííáåÖë iáÖÜí=iÉîW `çäçìêW iáÖÜí=qáãÉW `çåíê~ëíW W V tÜáíÉ NMë OQ F Fig. 4.
Handset Configuration To return to the user settings list press W. 4.2.1.2 Colour Highlight “Colour” and then use the X key to highlight the colour value. Press the V or W key to toggle the colour between “Red” and “White”. To return to the user settings list press W. To return to the user settings list press W. 4.2.1.4 LCD contrast Highlight “Contrast” and then use the X key to highlight the contrast value. Use the V or W keys to adjust the Display Contrast to a suitable level between 0 - 40.
WR20 Remote Commander 4.2.2 Unit selection Selecting “Unit selection” from the “WR20 Setup” menu will display data in predefined units of measurement, however, these can be changed to meet individual needs (Fig. 4.4). råáí==pÉäÉÅíáçå Handset Configuration aÉéíÜW _ç~í=péÉÉÇW táåÇ=péÉÉÇW aáëí~åÅÉW W j hq hq hj F Fig. 4.4 - Unit selection options The full list includes: • • • • • Depth Boat Speed Wind Speed Distance Temperature 4.2.2.
Handset Configuration 4.2.2.4 Distance units Highlight “Distance” and then use the X key to highlight the current units. Use the V or W keys to change between nautical miles, statute miles and kilometres. To return to the setup list press W. To return to the setup list press W. 4.2.3 Installation Selecting “Installation” from the “WR20 Setup” menu provides the following options (Fig 4.5). fåëí~ää~íáçå m~áê=íç=t_OM mêçÇìÅí=fåÑç== oÉëÉí=_Lpí~íáçå oÉëÉí=aÉÑ~ìäíë W F Fig. 4.
WR20 Remote Commander 4.2.3.2 Product info When “Product Info” is selected from the “Installation” menu, the Software Version and Serial Number is displayed for both the Handset and Basestation (Fig. 4.6). mêçÇìÅí==fåÑç Handset Configuration toOM toOM t_OM t_OM ptW pkW ptW pkW MMKPN t`MMMMVP MMKOO t`MMMMVQ F Fig. 4.6 - Product Info To return to the setup list press W. 4.2.3.3 Reset B/station The BaseStation is always powered on when it is connected to a live SimNet system.
Handset Configuration – in which case “Mobile Phone” will appear as a selectable item in the list of products when the PRODUCT key is pressed. Selecting the “Phone Setup” menu will display whether Mobile Phone support is switched on or off. To change the status, use the X key to highlight the current status and then use the V or W keys to adjust accordingly. To return to the setup list press W. For information on making and receiving calls via mobile phone please refer to section 10.
WR20 Remote Commander pÉäÉÅí==o~Çáç opUMJN=`ä~ëë=a opUMJO=`ä~ëë=a== F Fig. 4.8 - Selecting a radio Handset Configuration The WR20 will only control the VHF whose black box is connected directly to the wireless base station. If this is RS80-1 Class D in the example above then this radio must be selected from the list. All VHF operation from the handset will then control the selected radio. From the “Select Radio” menu select the appropriate radio from the list, and press MENU.
Product Selection 5 PRODUCT SELECTION 5.1 Product recognition Only WR20 compatible products will be available for selection. 5.2 Selecting from a list Press the PRODUCT key to display a list of products connected to the SimNet Network (Fig. 5.1). V pÉäÉÅí==mêçÇìÅí W ^ìíçéáä=K=K `ä~ëë=a k^spq^q=K=K= fåëí=póë F Fig. 5.1 - Product List Use the V or W keys to highlight the product you require. If there are more items above those being shown, then V will be displayed in the top left corner of the LCD.
Autopilot 6 AUTOPILOT 6.1 General The ability of the WR20 to control many different models of Simrad Autopilots may mean that some of the functions shown in this manual will not be relevant to the model you have purchased. However, the way the information is shown in the display will apply to current and future models. Please refer to the manual that came with your Autopilot for further information. 6.2 Display Select the Autopilot you wish to control from the product menu.
WR20 Remote Commander 6.3 Standby mode To gain control of the Autopilot, press STBY/AUTO key. The “Inactive” symbol disappears from the display, and the MODE SoftKey function appears (Fig. 6.2). ^mORJN N pq^ka_v eb^afkdW NPS°j m• • • • • • MR• • • • • • p F jlab Fig. 6.2 - Standby mode (Active) Autopilot In Standby mode pressing the W Port or X Starboard NavPad key will control the rudder. If either key is pressed, the display will indicate “Power Steer” (Fig. 6.3).
Autopilot ^mORJN N pí~åÇÄó ^rql=`çãé~ëë ^rql=kçaêáÑí `^k`bi F Fig. 6.4 - Steering mode Pressing CANCEL returns you to the previous mode Note Throughout this chapter, Pressing the MODE SoftKey when available will open the “Steering Mode” menu. 6.5 Auto Compass mode ^mORJN N ^mORJN N ^ìíç==`çãé~ëë ^ìíç==`çãé~ëë `lropbW eb^afkdW aladb F NPS NPV °j jlab Fig. 6.5 - Auto Compass (Powerboat) `lropbW eb^afkdW q^`h F NPS NPV °j jlab Fig. 6.
WR20 Remote Commander ^mORJN N aladb ^rql `ljm^pp `lropbW========NPV W mêÉëë=====X `^k`bi F Fig. 6.7 - DODGE (Powerboat) Note Pressing the CANCEL SoftKey returns you to the Auto Compass. Autopilot 6.5.2 TACK (Sailboat) Press the TACK SoftKey to initialise a Tack. Warning Gybing is not recommended when in Auto Compass mode as the Autopilot has no reference to the point at which the wind changes from one tack to the other.
Autopilot Pressing the CANCEL SoftKey within 5 second cancels the Tack and returns the boat to the original course. 6.6 Auto NoDrift mode Selecting the “Auto NoDrift” Mode from the menu, the following information will be displayed (Fig. 6.9). ^mORJN N ^ìíç==kçaêáÑí `lropbW eb^afkdW aladb F NPS NPV°j jlab Fig. 6.9 - Auto NoDrift display 6.6.1 DODGE Refer to section 6.5.1 6.7 Auto Nav mode As the display is loaded into the WR20 Handset, it will make a short notification beep.
WR20 Remote Commander The system is waiting for confirmation to enter Nav mode. Press the OK SoftKey to confirm course change and engage Auto Nav Mode. Press the CANCEL SoftKey to Cancel the Engage Auto Nav Prompt display and return to the previous Mode. Once confirmed and the Auto Nav Mode is engaged the display shows all relevant information (Fig. 6.11). ^mORJN N tmW uqbW ^ìíç==k~î oqmMMMN MKMNkj aladb F jlab Autopilot Fig. 6.11 - Auto Nav display 6.7.1 DODGE Refer to section 6.5.
Autopilot ^mORJN N ^ìíç==táåÇ tLpqbboW ^mm=tL^W q^`h F NPS mMQR jlab Fig. 6.12 - Auto Wind Mode Note 6.8.1 TACK/GYBE mode The function of the left SoftKey is dependent on angular wind data received by the Autopilot. “TACK” is only shown when sailing into wind and “GYBE” is only shown when sailing with the wind. To initialise a Tack/Gybe, press the TACK/GYBE SoftKey. Autopilot The display now shows “TACK” or “GYBE” flashing on the screen, Press OK to confirm this action (Fig. 6.13).
WR20 Remote Commander 6.9 Autopilot Alarms The Autopilots are programmed to provide essential alarms. The alarm message will appear on the WR20, and depending on the operating circumstances the alarm may inhibit some features of the WR20 until the alarm condition is cleared. Note For safety reasons an alarm can only be cleared at the Autopilot control head itself and not from the WR20 Handset.
Autopilot system the following message is displayed for 2 seconds (Fig. 6.15). ^mORJN N t^okfkd fmp=lsboofab jrqb F Fig. 6.15 - Volvo IPS override warning 41 Autopilot If the WR20 was previously controlling the Autopilot it will no longer be usable until the override condition is cleared. If the WR20 was previously controlling an instrument other than an Autopilot then following the warning message the WR20 display will return to the instrument under control.
VHF Radio/Intercom 7 VHF RADIO/INTERCOM 7.1 General The WR20 acts as an additional station to your VHF. Note that a separate cable is required to interface the WR20 Basestation to the VHF black box, (Section 2.4). The WR20 Handset operates the major functions of the VHF including changing channels, adjusting the volume of an attached external loudspeaker and adjusting the radio squelch. In addition intercom calls can be received and initiated between the WR20 Handset and any other station. 7.
WR20 Remote Commander Note Press PRODUCT at any time, to see the product list. 7.3 Changing channels To select the required channel press the or decrement the channel number. or keys to increment 7.4 Volume & squelch adjustment To select the volume of the external loudspeaker, press the W key. The display now shows “VOL” highlighted in the display. Use or to adjust the volume to the required level. To select the squelch, press the X key. The display now shows the “SQL” highlighted in the display.
VHF Radio/Intercom 7.8 Radio menus options Pressing the MENU key will display a menu of VHF radio options (Fig. 7.2). fkqbo`lj sec=o~Çáç pí~íáçå=N pí~íáçå=O pí~íáçå=P F Fig. 7.2 - Radio Options Menu Use the or keys to scroll through the options and highlight the one you require. Press the MENU or X key to enter that option. 7.8.1 VHF radio Selecting this option will return you back to the radio display. 7.8.
WR20 Remote Commander fkqbo`lj `~ääáåÖ pí~íáçå=N bka=`^ii F Fig. 7.3 - Intercom 7.8.3 Call all stations (Intercom) To call all stations, use the or keys to highlight the “All Stations” option. This is a broadcast and does not require a response by an end user. Press the PTT key to transmit your message. VHF Radio Intercom Pressing the END CALL SoftKey will terminate the “All Stations” Intercom call.
NavStation 8. NAVSTATION 8.1 General The WR20 Handset is able to control all of the major functions of WR20 compatible Chartplotters, Fishfinders and Navstations. The WR20 controls these products using both MENU selection and cursor control. Under MENU selection control options are presented in the WR20 screen. In cursor control the WR20 NavPad has the same functionality as the cursor keys on the Navstation.
WR20 Remote Commander 8.3 Navstation control Press the MENU SoftKey to bring up the four menu options. (Fig. 8.2): W- `uPQJN N +W jÉåì_~ê ^ag==jÉåì nìáÅâ==jÉåì mto==jÉåì `roplo F bufq Fig. 8.2 - Menu options 8.3.1 MENU option “MenuBar” - Equivalent to the MENU key on the main device. “ADJ Menu” - Equivalent to the ADJ key on the main device. “Quick Menu” - Equivalent to the ENT key on the main device. “PWR Menu” - Equivalent to the PWR key on the main device.
NavStation Pressing the WIN SoftKey allows you to toggle between the active window combinations on the primary products display. 8.3.2. KEY option Additional primary functions are provided by pressing the KEY SoftKey. This provides access to the functions shown in (Fig 8.4). W- `uPQJN N +W dlql milq tfk `io `roplo F bufq Fig. 8.4 - KEY options These options provide the same functions as the equivalent keys on the primary product.
WR20 Remote Commander All of the relevant information for an efficient rescue operation will be shown on the NavStations primary display. NavStation To turn off an active MOB, please refer to the NavStation user manual.
Instruments 9 INSTRUMENTS 9.1 General The WR20 Remote Commander can be used to control all of the major functions of any WR20 compatible instrument that is attached to the network. Note In order to view Instrument data on the WR20 display, please refer to section 11.2. 9.2 Display After selecting “INST SYS” from the product list, the WR20 display will show a list of instruments attached to the network (Fig. 9.1). V pÉäÉÅí==fåëí fpNOJM=tfka fpNOJM=`lj_f fpNOJM=abmqe fpNOJM=jbd^ W F Fig. 9.
WR20 Remote Commander fpNOJM M=abmqe LIGHT SHALL DEEP INFO H Fig. 9.2 - Depth Instrument The selected instrument will show “CTRL” flashing briefly in its display. The text legend shown on the keys in the WR20 display will emulate the keys of the selected instrument. For information on the functionality of each instruments keys, please refer to the relevant instrument user manual.
Mobile Phone 10 MOBILE PHONE 10.1 General Your WR20 can be paired with many makes of mobile phone that feature Bluetooth Headset support. The functions that are available will dependent on the specific phone used. Note that when operating in this mode the WR20 is disconnected from the Basestation and will automatically reconnect when the PRODUCT key is pressed. 10.2 Enabling mobile phone connectivity Mobile Phone support can be switched on or off in the “Phone Setup” menu within the “WR20 Setup” menu (4.
WR20 Remote Commander Press the MENU key to Pair your phone to the Handset. The display changes (Fig. 10.2). mÜçåÉ==jÉåì m~áê==íç==éÜçåÉ F Fig. 10.2 - Phone Menu Note If your phone has previously been Paired, “Delete Pairing” will also be shown as a second option in the Phone Menu above. Highlight, “Pair to Phone” and press the MENU key to select it. The Handset enters pairing mode, it generates and displays a security PIN (Fig.10.3).
Mobile Phone 10.4 Making/receiving calls From the top level product list select “Mobile Phone”.The display will change as shown in (Fig. 10.4). jçÄáäÉ==mÜçåÉ W sçäìãÉ W F slf`b af^iifkd Fig. 10.4 - Mobile Phone Options For the features available please refer to the phone’s user manual. The following common features may be used as a guideline. • The audio volume can be controlled using the V or W keys on the NavPad. • Calls initiated on the mobile phone will be simultaneously available on the WR20.
WR20 Remote Commander 10.5 Range Most mobile phones support Bluetooth Class 11 which have a more limited range than Class 1. This means that the distance between the mobile phone and WR20 Handset should be within the same range limits as for a Bluetooth Headset (typically up to 10m). 10.6 Reconnect to Basestation To reconnect to the WR20 Basestation at any time press the PRODUCT key. This will hangup any calls in progress.
Data Displays 11 DATA DISPLAYS 11.1 General The WR20 can display data from various sources on the network simultaneously. The display is user configurable both in terms of the type of data to be shown and also the number of lines of data in the display (maximum of 4). If only 1 or 2 Data Items are to be displayed, then the size of the displayed data is enlarged. The units in which data is displayed are also selectable, please refer to Section 4.2.2. 11.
WR20 Remote Commander a~í~m~ÖÉ==O NNKO j TKM hq NPM° j abmqeW _pmbbaW eb^afkdW F Fig. 11.2 - An example DataPage Note Information from sources not controllable by the WR20 will be displayed if the data has been converted to SimNet format. For example, data from an NMEA source converted to SimNet using an AT10 converter. 11.2.
Data Displays bÇáí==a~í~é~ÖÉ==O t~íÉê=aÉéíÜ _ç~í=péÉÉÇ eÉ~ÇáåÖ=j~Ö objlsb F ^aa Fig. 11.3 - Edit DataPage screen 11.3.1 Adding a DataPage item On entering the “Edit DataPage” screen, the display shows the current data. Press the ADD SoftKey and the display changes to show a list of “Data groups” available (Fig. 11.4). a~í~==dêçìéë eÉ~ÇáåÖ=a~í~ k~îáÖ~íáçå táåÇ=a~í~ péÉÉÇ=C=içÖ W F Fig. 11.
WR20 Remote Commander k~îáÖ~íáçå `êçëë=qê~Åâ=bêê _É~êáåÖ=íç=tm táåÇ=a~í~ péÉÉÇ=C=içÖ W F Fig. 11.5 - Selected group item list Using the V or W keys, highlight the Data Item required, and press the MENU or key to accept. This will return you to the “Edit DataPage” screen. To continue adding items, repeat the stages from the beginning of this section (11.3.1) or to accept the change and display the new DataPage press the key (Fig.11.6).
Data Displays The display changes to show the list of Data Groups available, highlighting by default, the Data Group which the current Data Item being exchanged comes from (Fig. 11.8). a~í~==dêçìéë eÉ~ÇáåÖ=a~í~ k~îáÖ~íáçå táåÇ=a~í~ péÉÉÇ=C=içÖ W F Fig. 11.8 - Data group list If you require another item from the same Data Group press the MENU or key. If you require an item from another Data Group, use the V or W keys to scroll through the available Groups and highlight the one you want.
WR20 Remote Commander a~í~é~ÖÉ==O NNKO j TKM hq NPM°j SSKTS kj abmqeW _pmbbaW eb^afkdW aqtW F Fig. 11.10 - New DataPage 11.3.3 Removing a DataPage item On entering the “Edit DataPage” screen, the display shows the current data. Use the V or W keys to highlight the Data Item you want to remove, then press the REMOVE SoftKey to delete the selected item. Note The ADD SoftKey will always be present if there are less than 4 items on the DataPage. 11.
Data Displays Wind Data App Wind Angle App Wind Speed Tru Wind Angle Tru Wind Speed Speed & Log Boat Speed Speed Over Gnd Cumulative Log Trip Distance Race Timer Environmental Sea Temp Depth Data Water Depth Shallow Alarm Deep Alarm Pilot Data Rudder Angle Position Posn Lat/Lng Posn Latitude Posn Longitude Time UTC Date DD/MM/YY Date MM/DD/YY Data Displays 63
Appendix. 12 APPENDIX 12.1 Maintenance and battery replacement The WR20 Handset and Basestation are sealed waterproof units. To create and maintain their waterproof integrity they were assembled in a controlled environment using special equipment. The units are not user maintainable and under no circumstances should they be opened. For battery replacement or other service please contact your local authorised Simrad Service Agent. 12.
WR20 Remote Commander 12.3 Troubleshooting These simple checks should be carried out before seeking technical assistance and may save time and expense. General Symptoms Possible Cause Remedy Handset will not switch on • Battery Not Charged • Re-charge battery Communication Failure • Handset out of Range of Basestation • Handset not Paired to Basestation • Move handset closer to Basestation • Pair Handset to Basestation ( Section 12.
Appendix. 12.5 Dimensions 29mm (1.2”) 55mm (2.2”) 60mm (2.4”) WR20 RemoteCommander 92mm (3.7”) 133mm (5.5”) 36mm (1.4”) WR20 Battery Charger Appendix 59mm (2.3”) 61mm (2.4”) 150mm (6.
WR20 Remote Commander 12.
Appendix. 12.8 Declaration of Conformity (EU) Hereby, Simrad Limited (Margate) declares that this RS81/82 VHF Radio is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Finnish Simrad Limited (Margate) vakuuttaa täten että RS81/82 VHF Radio tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
WR20 Remote Commander 12.9 Declaration of Conformity (USA) WR20 RemoteCommander and WB20 Basestation FCC Class B Certification This above mentioned devices comply with Part 15 of the FCC Rules. Operation is subject to the following conditions: • These devices may not cause harmful interference, and • These devices must accept any interference received, including interference that may cause undesired operation.
