Satellite Radio User Manual
5
SIR-ALP10T Operation and Installation Guide
4
SCH1C SIRIUS Connect Tuner Installation Guide
5
SCH1C SIRIUS Connect Tuner Installation Guide
WARNING
This symbol means important
instructions. Failure to heed them can
result in serious injury or death.
Any function that requires your prolonged
attention should only be performed after
coming to a complete stop. Always stop
the vehicle in a safe location before
performing these functions. Failure to do
so may result in an accident.
DO NOT OPEN, DISASSEMBLE OR
ALTER THE UNIT IN ANY WAY. Doing so
may result in fire, electric shock or product
damage.
DO NOT INSERT ANY OBJECTS INTO
THE UNIT. Doing so may result in fire,
electric shock or product damage.
MAKE THE CORRECT CONNECTIONS.
Failure to make proper connections may
result in fire or product damage.
DO NOT SPLICE INTO A ELECTRICAL
CABLES. Never cut away cable insulation
to supply power to other equipment. Doing
so will exceed the current carrying capacity
of the wire and result in fire or electric
shock.
DO NOT INSTALL THE UNIT IN AREAS
WHERE THERE ARE HIGH LEVELS OF
HUMIDITY, MOISTURE OR DUST. Doing
so can result in electric shock or product
failure.
FCC Warning: This equipment may
generate or use radio frequency energy.
Changes or modifications to this
equipment may cause harmful interference
unless the modifications are expressly
approved in this User Guide. The user
could lose the authority to operate this
equipment if an unauthorized change or
modification is made.
Note: This equipment has been tested and
found to comply with Part 15 of the FCC
Rules. These rules are designed to
provide reasonable protection against
harmful interference. This equipment may
cause harmful interference to radio
communications if it is not installed and
used in accordance with these
instructions. However, there is no
guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio
or television reception, which can be
determined by turning the equipment off
and on, the user is encouraged to try to
correct the interference by one of more of
the following measures:
• Relocate the receiving antenna.
• Consult the dealer or an experienced
technician for help.
CAUTION
This symbol means important
instructions. Failure to heed them can
result in injury or material property
damage.
HALT USE IMMEDIATELY IF A PROBLEM
APPEARS. Failure to do so may cause
personal injury or damage to the product.
Return the tuner to your authorized retailer
or nearest service center for repairing.
INSTALL THE WIRING SO THAT IT IS
NOT CRIMPED OR PINCHED BY
SCREWS OR SHARP METAL EDGES.
Route the cables away from moving parts
or sharp pointed edges. This will prevent
crimping and damage to the wiring. If the
wiring must pass through a metal hole, be
sure to use a rubber grommet to prevent
the wire’s insulation from being cut by the
metal edge of the hole.
USE THE SPECIFIED ACCESSORY
PARTS AND INSTALL THE PRODUCT
SECURELY. Be sure to use only the
specified accessory parts. Use of non-
specified parts may damage this unit
internally or may not securely install the
unit in place. This may cause parts to
become loose, resulting in hazards or
product failure.
Installation
It is recommended that prior to starting the
installation, you read this installation
section completely and follow the
instructions. In addition, consult the
manual of the audio device to which you
will be connecting the SCH1C Tuner to
determine the required installation
configuration:
• If power for the SCH1C Tuner is not
provided by your audio device via the
DIN cable connection, you will need to
use the provided AC Power Adapter to
provide power for the SCH1C Tuner.
• If audio input from the SCH1CTuner
is not suported via the DIN cable
connection of your audio device, you
will need to connect the audio output
of the SCH1C Tuner to your audio
system via the RCA-type or Optical
audio output connectors of the tuner.
(You will need to purchase the
appropriate cable separately.)
Mounting the SCH1C Tuner
Consider the mounting location carefully to
be sure that you avoid the following:
• Any location where the tuner is
exposed to moisture.
• Any location where the tuner is
exposed to extreme heat.
The tuner may be mounted on a wall with
#10 screws, using the slots on the
underside of the tuner to hang on the tuner
on the screws. Alternately, the tuner may
be placed on any flat surface.
1
2
3
4
5
HORIZON
SKY
SOUTH
WEST EAST
NORTH
SCREW
MOUNTING SLOTS