Integration Instructions

ManualsBrandsSkylab M&C Technology ManualsElectronicsWIFI module

Compliance list INTEGRATION INSTRUCTIONS for 996369 D03 OEM the and 996369 D03 OEM by

Sections 2.2 through 2.10.

Requirement Yes N/A Comment

2.2 List of applicable FCC rules

List the FCC rules that are applicable to the

modular transmitter. These are the rules that

specifically establish the bands of operation,

the power, spurious emissions, and operating

fundamental frequencies. DO NOT list

compliance to unintentional‐radiator rules

(Part 15 Subpart B) since that is not a

condition of a module grant that is extended

to a host manufacturer. See also Section 2.10

below concerning the need to notify host

manufacturers that further testing is

required.

YES Refer to instruction

FCC standards: FC C CFR Title 47 Part 15

Subpart C Section 15.247 and FCC CFR Title 47

Part 15 Subpart E Section 15.407: 2016

2.3 Summarize the specific operational use

conditions

Describe use conditions that are applicable to

the modular transmitter, including for

example any limits on antennas, etc. For

example, if point‐to‐point antennas are used

that require reduction in power or

compensation for cable loss, then this

information must be in the instructions. If the

use condition limitations extend to

professional users, then instructions must

state that this information also extends to the

host manufacturer’s instruction manual. In

addition, certain information may also be

needed, such as peak gain per frequency band

and minimum gain, specifically for master

devices in 5 GHz DFS bands.

YES Refer to instruction

Antenna Type:External Antenna

Antenna Gain: 2dBi

2.4 Limited module procedures

If a modular transmitter is approved as a

“limited module,” then the module

manufacturer is responsible for approving the

host environment that the limited module is

used with. The manufacturer of a limited

module must describe, both in the filing and in

the installation instructions, the alternative

means that the limited module manufacturer

uses to verify that the host meets the

necessary requirements to satisfy the module

limiting conditions.

A limited module manufacturer has the

flexibility to define its alternative method to

address the conditions that limit the initial

YES Refer to instruction

We will retain control over the final installation

of the modular such that compliance of the end

product is assured. In such cases, an operating

condition on the limit modular approval for the

module must be only approved for use when

installed in devices produced by a specific

manufacturer. If any hardware modify or RF

control software modify will be made by host

manufacturer,C2PC or new certificate should be

apply to get approval,if those change and

modification made by host manufacturer not

expressly approved by the party responsible for

compliance ,then it is illegal.

Summary of content (5 pages)

PAGE 1
Compliance list INTEGRATION INSTRUCTIONS for 996369 D03 OEM the and 996369 D03 OEM by Sections 2.2 through 2.10. Requirement 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies.
PAGE 2
approval, such as: shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation. The alternative method could include that the limited module manufacturer reviews detailed test data or host designs prior to giving the host manufacturer approval. This limited module procedure is also applicable for RF exposure evaluation when it is necessary to demonstrate compliance in a specific host.
PAGE 3
and specifications; e) Test procedures for design verification; and f) Production test procedures for ensuring compliance. The module grantee shall provide a notice that any deviation(s) from the defined parameters of the antenna trace, as described by the instructions, require that the host product manufacturer must notify the module grantee that they wish to change the antenna trace design.
PAGE 4
to be a specific “antenna type”)). For situations where the host product manufacturer is responsible for an external connector, for example with an RF pin and antenna trace design, the integration instructions shall inform the installer that unique antenna connector must be used on the Part 15 authorized transmitters used in the host product. The module manufacturers shall provide a list of acceptable unique connectors. 2.
PAGE 5
The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.