Owner Manual

1
2
T-joint
Socket
spring holes
face the ground
spring holes
face the ground
Horizontal square tube
(used to connect the Top tube)
Vertical round tube
(used to connect the Leg extension)
T-joint
Horizontal square tube
(used to connect the Top tube)
Vertical round tube
(used to connect the Leg extension)
Vertical square tube
(used to connect Enclosure pole)
Socket
1
15
Key No. Qty. Description
1 6 Top Tube with T-joint
2 6 Top Tube with Socket
3 12 Leg extension
4 6 Leg brace
5 1 Jumping mat
6 1 Frame Pad
7 1 Enclosure net
8 72 Spring
9 6 Straight Tube
10 6 Curved Tube
11 12 Foam
12 6 Pole Cap
13 6 End Cap
14 6 M5x50mm Bolt
15 33 M4.8x16mm Self-tapping Screw(3 spare parts) 16
1 Spring Tool
17 1 Screw Driver #
1 User’s Manual and Safety Placard #
1 Set of ASTM Frame Labels
#These parts are not illustrated. Specifications are subject to change without notice.
ORDERING REPLACEMENT PARTS
To order replacement parts, visit our web site at www.skywalkertrampolines.com or call our toll-free Customer Care
Hot Line at 1-866-603-Jump (5867), Monday through Friday, 8 a.m. until 5 p.m. Mountain Time (excluding holidays).
To help us assist you, please provide the following information when calling:
• the MODEL of the trampoline (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part (see the PART LIST above)
• the quantity needed
• the desired method of shipping
ASSEMBLY
ASSEMBLY (PUTTING THE TRAMPOLINE AND ENCLOSURE TOGETHER)
IMPORTANT ASSEMBLY INFORMATION
• Need phillips screw driver (included with trampoline) and 2 adjustable wrenches (for putting the trampoline together). A rubber
mallet is also recommended to make assembly easier.
• Assembly requires two adults. Keep children away from the trampoline and enclosure until they are completely put together.
• Use gloves to protect your hands from pinch points during assembly.
• Make sure that the trampoline is properly put together, with the frame pad correctly laid out, before you put together the trampoline
enclosure.
• The assembly steps refer to parts by their descriptions and key numbers (see the PARTS LIST on page 14 and make sure that all
listed parts are included. If a part is missing, refer to ORDERING REPLACEMENT PARTS at the bottom of page 14.
TRAMPOLINE PLACEMENT
1. Place the trampoline and enclosure on a level surface before you use it.
2. Adequate overhead clearance is essential. A minimum of 24 feet (7.3 meters) from the ground is recommended. Provide clearance
from wires, tree limbs, and other possible hazards. Lateral (sideways) clearance is also essential. Place the trampoline and enclosure
away from walls, structures, fences, and other play areas. Maintain a clear space on all sides of the trampoline and enclosure.
3. Use the trampoline in a well-lighted area. If the trampoline is indoors or in a shady areas you may need to use artificial (electrical)
lighting in the area.
4. Secure the trampoline and enclosure against unauthorized and unsupervised use.
5. Remove any objects from under the trampoline and enclosure.
6. The owner and supervisors of the trampoline are responsible to make all users aware of practices specified in this manual.
7. The trampoline enclosure is only to be used as an enclosure for a specific round trampoline.
Trampoline and Enclosure Assembly
To make assembly easier, read the assembly tips at the top of
this page.
1. Locate the Top tube with T-joint(1) and the Top tube
with Socket(2) as shown.
NOTE: Make sure all the spring holes are facing the
ground during this step.
NOTE: If you don’t assemble in the right order, you will
have to
disassemble the entire trampoline in order to attach
correctly.
Identify the T-joint and Socket shown in right will be
helpful for you, they are pre-installed on Top tube.