Installation Sheet

18.50”
(470 mm)
5.5”
(140 mm)
1.5”
(38 mm)
14.25”
(362 mm)
10.125”
(257 mm)
14”
(358 mm)
27”
(682 mm)
6.125”
(155 mm)
17”
(430 mm)
14”
(358 mm)
10.75”
(273 mm)
15.35”
(390 mm)
(73 mm)
12”
(305 mm)
2.875”
15”
(381 mm)
13.35”
(339 mm)
• Using putty knife, completely
remove old wax seal from oor and
bottom of water closet.
• Lay water closet down on padded
surface to help protect the vitreous
china.
WARNING: Hazardous gases
can escape through the closet flange if new water
closet is not installed quickly. A temporary fix:
place a large rag in the closet flange.
THE RIGHT CHOICE
We thank you for your purchase.
Our products are 100% tested but should you have
any questions, please contact us by phone or at our
web site.
Rear Spud Water Closet Installation Instructions
Anillo
de cera
anterior
Cubra con tela
Old
wax ring
Cover with rag
TO MAXIMIZE THE PERFORMANCE OF YOUR SLOAN WATER CLOSET, USE ONLY SLOAN FLUSHOMETERS
NOTE: All vitreous china dimensions shown in these drawings are
nominal. Dimensions can vary within the tolerances established
in the governing ASME A112.19.2/CSA B45.1 standard. Please
take this into consideration when planning rough-in and plumbing
layouts.
2. INSTALLING NEW WATER CLOSET
• Check rough-in dimensions and install or relocate
ush valve and outlet as indicated.
• Record model number for reference.
• Place and press in a new wax seal around the
water closet bottom outlet.
• Install new 5/16 “T-bolts.
WARNING: Any vitreous china can chip or
break if the bolts or nuts are over-tightened or
if mishandled.
BEFORE YOU START…
• Check all local plumbing and building codes.
• Check for any damage to the new water closet
before installation.
WHAT YOU WILL NEED…
• Putty knife • Sponge
• Safety glasses • 10” adjustable wrench
• Measuring tape • Large level
• Spud wrench • Wax seal
NOTE: Plumbing System Requirements
√ Minimum Flowing Pressure: 25 PSI
√ Minimum Flow Rate: 25 GPM
√ Maximum Static Pressure: 80 PSI
1. REMOVAL OF EXISTING WATER
CLOSET
• Turn off the water supply.
• Disconnect the ush valve.
• Remove the existing water closet.
• Take out the temporary rag (if used) from the water
closet ange hole.
• Carefully align and lower the water closet over the
ange and T-bolts.
IMPORTANT! Do not lift or rock the water closet
after replacement. The watertight seal will have
to be replaced if breakage occurs.
• To seal, apply your full body weight around the
water closet.
• Place the plastic cap base in the position indicated
on cap as marked.
• The metal washers and nuts can now be placed on
the bolt cap base and T-bolts.
IMPORTANT! Do not overtighten the nuts,
breakage and chipping of vitreous china can
occur.
• Cut 1/4” or more over the top of the nut.
• Attach the bolt caps.
IMPORTANT! Product damage can occur if
using a saw blade to cut off the excess T-bolt
length. Make sure vitreous china is protected
and covered.
3. COMPLETING THE INSTALLATION
• Flush valve should be installed to manufacturer’s
installation instructions.
• Turn on water supply valve.
• Install toilet seat (not included).
• Tighten the nuts carefully.
• Flush water closet a few times and check all
connections for water seepage.
• Check for leaks.
CARE
AND CLEANING OF VITREOUS CHINA
Clean water closet with a cleaner safe for vitreous
china. Spray and wipe clean using soft cloth. Soft
abrasive cleaners may be used to remove stains.
LIMITED WARRANTY
Sloan Valve Company warrants its products to be
made of rst class materials, free from defects of
material or workmanship under normal use and to
perform the service for which they are intended in
a thoroughly reliable and efcient manner when
properly installed and serviced, for a period of three
years (one year for special nishes) from date of
purchase. During this period, Sloan Valve Company
will, at its option, repair or replace any part or parts
which prove to be thus defective if returned to Sloan
Valve Company, at customer’s cost, and this shall
be the sole remedy available under this warranty. No
claims will be allowed for labor, transportation or other
incidental costs. This warranty extends only to persons
or organizations who purchase Sloan Valve Company’s
products directly from Sloan Valve Company for
purpose of resale.
THERE ARE NO WARRANTIES WHICH
EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF. IN NO EVENT IS SLOAN
VALVE COMPANY RESPONSIBLE FOR ANY
CONSEQUENTIAL DAMAGES OF ANY MEASURE
WHATSOEVER.
NOTE: IN NO EVENT SHALL THE SLOAN VALVE
COMPANY BE LIABLE FOR INCIDENTAL DAMAGES,
RESULTING FROM IMPROPER INSTALLATION, OR
FOR DAMAGES CAUSED BY NEGLECT, ABUSE
OR ALTERATION.
The information contained in this document is subject to change
without notice.
SLOAN
10500 Seymour Avenue
Franklin Park, IL 60131
Phone: 1-800-9-VALVE-9 (982-5839)
or 1-847-671-4300
Fax: [phone] or 1-847-671-4380
www.sloan.com
Copyright © 2017 Sloan Valve Company
Printed in the U.S.A.
Code No. 0816692 Rev.2 (03-17)