Installation Instructions

32
Before beginning assembly, installation, or operation of product, make sure all parts are present. Compare
parts with package and hardware contents list on page 1. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts: 1-844-255-9692
Monday – Friday 9:00 a.m. – 6:00 p.m. CST.
Tools Required for Assembly (not included): Suitable Fasteners, Screwdriver, Tape Measure, Pencil, Safety
Glasses, and Ladder
SAFETY INFORMATION
PREPARATION
DANGER
• Be careful not to damage or cut the jacket of the power cord during xture installation. Do not permit power
cord to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which
could cause serious injury or death from electric shock.
• This xture requires a 120V AC electrical wall socket for operation and consumes 36W per xture.
• This xture can be mounted two ways: suspended via mounting chain or surface mounted.
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS (continued)
WARNING: These products may represent a possible shock or re hazard if improperly installed or attached
in any way. Products should be installed in accordance with these instructions, current electrical codes, and/or
the current National Electric Code (NEC).
WARNING: To reduce risk of re, electric shock, or injury to persons, be sure that power supply is turned o󰀨
at fuse box or circuit breaker before attempting installation or servicing of the xture. For safest operation, read
and become familiar with complete installation instructions prior to use. Pay close attention to this manual and
stay within its guidelines when using this product.
SAVE THESE INSTRUCTIONS
ADDITIONAL SAFETY MEASURES
1. To avoid electrical shock, do not turn on xture with missing or damaged lens.
2. There are no serviceable parts inside LED module.
3. LEDs emit bright light. Avoid looking directly at the light source.
4. Do not alter the power cord in any way.
5. Do not use with any other cord, cable, or connector other than those provided with the xture.
6. Not to be used with a dimming circuit.
7. This xture is suitable for dry and damp locations.
8. Do not mount over a sink, tub or shower.
1. Select a suitable location for the Grow Light that can support
its weight, and that has an outlet on the ceiling to ensure that
the xture is powered properly. Determine mounting method.
For suspended mounting via mounting chain, go to Step 2. For
surface mounting, go to Step 5.
Fig. 1
2. For suspended mounting via mounting chain (B): Mark two
locations on the ceiling that are 41 inches apart. and attach
suitable fasteners (not included) at the marked locations.
For mounting to drywall ceilings, toggle bolt j-hooks are
recommended. For mounting to wood ceilings, standard
j-hooks are recommended.
Fig. 2
41in.
3. First, attach one mounting chain (B) to the xture using one
S hook (C) provided. Repeat with second mounting chain (B)
and second S hook (C) at other end of xture.
Fig. 3
4. Put each mounting chain (B) over the mounting hooks
attached to the ceiling and adjust the chains over the hooks as
needed so that the xture hangs level. Move to step 7.
Fig. 4
7. Plug the attached power cord into a ceiling outlet and use the
pull chain to operate ON and OFF functions. Installation is
complete for one xture.
5. For surface mounting: Mark two locations on the surface that
are 40-3/8”apart. Start holes in mounting surface with screw-
gun or awl, then insert the drywall anchors (E) using a hammer
until ush with the drywall. Screw in mounting screws (D) at
these locations. Do not screw all the way in; be sure to leave
approximately 1/4”-1/2” of screws exposed to slide on the
xture.
6. Bring the xture to the mounting surface and slide the
mounting slots on to the screw heads.
Fig. 7
Fig. 5
Fig. 6
8. Multiple xtures (up to eight) can be linked together and
powered by one power cord. WARNING: When linking
multiple xtures, UNPLUG POWERCORD FROM OUTLET
BEFORE PROCEEDING. Follow steps 1-4 (or step 5 for surface
mounting) for the additional xture(s). Ensure each xture end
is no more than 5 feet apart to allow for power cord to reach.
Fig. 8
41in.
41in.
40-3/8in.
<5ft.
9. Plug the attached power cord from each subsequent
xture into the OUTPUT end of the existing xture.
Plug the attached power cord from the rst xture in
the series back into outlet as shown in step 5.
Fig. 9
A
A
A
A
A A
C
B
B