Quick Start Guide SR516ac This Quick Start Guide shows you how to set up and start using your new gateway.
Installation 1. Connect one end of the included phone cable to the DSL port on the gateway and connect the other end to the wall jack. 2. Connect one end of an Ethernet cable to a LAN port of the gateway and connect the other end to your PC. 3. Plug the power adapter into the wall outlet and connect the other end of it to the Power port of the gateway. 4. Turn on the unit by pressing the On/Off button on the left side of the gateway. Your gateway is now automatically being set up to connect to the Internet.
LED INDICATORS The LEDs on the front of the SR516ac gateway can help you understand the current state of your adapter.
QUICK GATEWAY CONFIGURATION Warning: Do not press the Reset button unless you want to clear the current settings. The Reset button is in a small circular hole on the rear panel. If you want to restore the default settings, insert a thin wire (such as a paper clip) into the hole, press the Reset button for 1 second, and then release the button. The system reboots and returns to the factory defaults.
Configuring the WAN manually If the automatic connect process is unsuccessful, refer to the Advanced Setup > Layer 2 Interface and WAN Service sections of the SmartRG SR516ac Gateway User Manual to manually establish a connection.
WiFi Setup Two methods, WPS and Manual, are available for WiFi setup. Perform the steps on this page first, and then follow the instructions for the applicable method. The default settings work for most situations. 1. In the left menu, click Wireless and then click 2.4 GHz Band or 5 GHz Band. The fields are the same for both options. The wireless radio is enabled by default. 2. Continue with the steps for the method you prefer.
WPS Method If the device you wish to connect to the Internet via your gateway supports the WPS secure Wi-Fi connection method, follow these steps. 1. In the left navigation bar, click Wireless, then click the band that you want to configure, and then click Security. 2. In the Enable WPS field, make sure that Enabled is selected, and then click Apply/Save to save your change. 3. On the left side of the gateway’s exterior: a. Activate the desired band by pressing 2.4 GHz or 5 GHz briefly on the rocker switch.
Manual Method Set up your gateway’s parameters first, then follow these steps. 1. In the left menu, click Wireless and then the band that you want to configure. 2. Click Security and scroll down to the Manual Setup AP section. 3. If your gateway supports multiple wireless networks, select the SSID of the network you wish to configure. You will need this ID for step 8. 4. Select the desired Network Authentication. Make sure that the host devices you intend to use support the selected authentication type. 5.
Record Your SR516ac Wi-Fi Settings Predefined wireless settings If you change the preset wireless settings WiFi network name (SSID) Network key (password) Additional Support If you require further instructions, please contact your local ISP Support. SMARTRG INC. ALL RIGHTS RESERVED.
Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 3.
FCC Statements FCC - Part 68 This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom case of this equipment is a label that contains, among other information, a product identifier in the format US: VW7DL01ASR516A .
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with this equipment, for repair or warranty information, please contact SmartRG,Inc.
FCC - Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Canada Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
