EZConnect CARD 10/100/1000 EZ N 32-bit 10/100/1000Mbps Gigabit Ethernet PCI Adapter Draft 11n Wireless USB2.
Copyright Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice. Copyright © 2008 by SMC Networks, Inc.
Limited Warranty Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or replace any product not operating as warranted with a similar or functionally equivalent product, during the applicable warranty term.
WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS.
Compliances FCC - Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications.
power supply: ±1 kV, Data/Signal lines: ±0.5 kV) • Surge immunity test according to EN 61000-4-5:1995 (AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV) • Immunity to conducted disturbances, Induced by radio-frequency fields: EN 61000-4-6:1996 (0.
Veuillez lire à fond l’information de la sécurité suivante avant d’installer le Device: AVERTISSEMENT: L.installation et la dépose de ce groupe doivent être confiés à un personnel qualifié. • Ne branchez pas votre appareil sur une prise secteur (alimentation électrique) lorsqu’il n’y a pas de connexion de mise à la terre (mise à la masse). • • Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de respecter les normes internationales de sécurité. Le coupleur d.
nur gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter SELV-Bedingungen betrieben werden Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft werden: Dieser Stromstecker muß die SEV/ASE Schweiz 1011Bestimmungen ein- halten. Das Netzkabel muß vom Typ Europe HO3VVF3GO.75 (Mindestanforderung) sein und die Aufschrift oder tragen Der Netzstecker muß die Norm CEE 7/7 erfüllen (.SCHUKO.).
Achtung: Installation und Deinstallation des Gerätes müssen von qualifiziertem Servicepersonal durchgeführt werden. Achtung: Wenn das Gerät an eine Steckdose angeschlossen wird, muß der Masseanschluß n Netzstecker mit Schutzerde verbunden werden, um elektrische Gefahren zu vermeiden.
Environmental Statement The manufacturer of this product endeavours to sustain an environmentally-friendly policy throughout the entire production process. This is achieved though the following means: • • • • • • Adherence to national legislation and regulations on environmental production standards. Conservation of operational resources. Waste reduction and safe disposal of all harmful un-recyclable by-products. Recycling of all reusable waste content.
Package Contents The following items should be found in your box: ¾ One 10/100/1000Mbps Gigabit Ethernet PC Adapter ¾ One Resource CD, including • Drivers • User Guide • Other Helpful Information ) Note: Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor for assistance.
CONTENT Chapter 1. Introduction............................................................................................ 1 1.1 Convention ......................................................................................................... 1 1.2 Product Overview ............................................................................................... 1 1.3 Main Features .................................................................................................... 2 1.4 LED Status ........
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide Chapter 1. Introduction Thank you for choosing SMC9452TX-2 Gigabit PCI Ethernet Adapter. 1.1 Convention The Adapter or SMC9452TX-2 mentioned in this User Guide stands for SMC9452TX-2 Gigabit PCI Ethernet Adapter. 1.2 Product Overview SMC9452TX-2 is a highly integrated and cost-effective single-chip Gigabit Ethernet Adapter that provides 32-bit performance, PCI bus master capability, and full compliance with IEEE 802.3 10Base-T, IEEE802.
SMC9452TX-2 1.3 Gigabit PCI Ethernet Adapter User Guide Main Features ¾ Integrated Ethernet MAC, Physical chip and transceiver in one chip ¾ Complies with the IEEE802.1P, IEEE802.1Q, IEEE802.3 10Base-T, IEEE802.3u 100Base-TX and IEEE802.3ab 1000Base-T standard ¾ Compliant to PCI Revision 2.1/2.2 ¾ Supports Full Duplex Flow Control (IEEE 802.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide Chapter 2. Installation 2.1 Hardware Installation To install the adapter, follow these steps listed below: Step 1: Turn off your computer and unplug the power cord and all cables. Step 2: Remove your computer’s case cover. See your computer’s user guide for information about removing the cover. Step 3: Locate an available PCI slot. PCI slot are usually white.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide 2.2 Software Installation In this User Guide, we will take the driver installation in Windows XP for example, which is similar to the driver installation procedures for the other operation systems. 2.2.1 Install driver for XP Step 1: After you insert the Adapter in the computer firmly, the Operating System will automatically recognize it, then the “Welcome to the Found New Hardware Wizard” screen will appear (shown in Figure 2-2).
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide Step 2: Select Install from a list or specific location (Advanced) as shown in Figure 2-3, and then click Next. Figure 2-3 Step 3: Select Don’t search. I will choose the driver to install as shown below. Then click Next.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide Step 4: Select Show All Devices as shown in Figure 2-5, then click Next. Figure 2-4 Step 5: Click Have Disk… in the next screen Figure 2-6.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide Step 6: After that, select Browse… as shown in Figure 2-7 to locate the driver in the next screen. Figure 2-6 Step 7: Locate the appointed driver as shown in Figure 2-8, click Open.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide Step 8: After that, you will see the next screen (shown in Figure 2-9), click OK. Figure 2-8 Step 9: Select the model of the Adapter as shown in Figure 2-10, then click Next.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide Step 10: After that, please wait few seconds for the wizard installing the software. Figure 2-10 ) Note: During the installation, a warning box about Windows Logo testing (shown in Figure 2-12) may pop up, please click Continue Anyway to continue the installation since our drivers have been tested thoroughly and are able to work with the operating system.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide Step 11: Finally, click Finish. And the driver installation for Windows XP completes.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide 2.2.2 Update driver for XP If the Welcome to the Found New Hardware Wizard screen does not appear after you insert the Adapter, you can follow the steps below to install the driver, and you can also upgrade the latest driver available on the CD-ROM in this way. Step 1: Right-click My Computer icon on the computer and select Properties (show in Figure 2-14). Figure 2-13 Step 2: Select Hardware and then Device Manager (shown in Figure 2-15).
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide Step 3: Right-click SMC9452TX-2 Gigabit PCI Ethernet Adapter, then select Update Driver… in Figure 2-16. (Note: If the driver was installed exactly, you may see "Ethernet Controller" instead. Right-click on it.) Figure 2-15 Step 4: The Hardware Update Wizard will appear, Click No, not this time, and then click Next.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide Step 5: Select Install from a list or specific location (Advanced) as shown in Figure 2-18, and then click Next. Figure 2-18 Step 6: Select Don’t search. I will choose the driver to install as shown below. Then click Next.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide Step 7: Select the model of the Adapter as shown in Figure 2-20, then click Next. Figure 2-17 Step 8: After that, select Browse… to locate the driver in the next screen.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide Step 9: Locate the appointed driver as shown in Figure 2-22, click Open. Figure 2-22 Step 10: After that, you will see the next screen, click OK. Figure 2-18 ) Note: Assuming D is the letter of your CD-ROM drive.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide Step 11: Select the model of the Card as shown in Figure 2-24, then click Next. Figure 2-24 Step 12: After that, please wait few seconds for the wizard installing the software.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide ) Note: During the installation, a warning box about Windows Logo testing (shown in Figure 2-11) may pop up, please click Continue Anyway to continue the installation since our drivers have been tested thoroughly and are able to work with the operating system. Figure 2-26 Step 13: Finally, click Finish. And the driver installation for Windows XP completes.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide 2.2.3 Update driver for Vista step 1. Insert the Driver & Installation CD into your CD-ROM drive, right-click the Computer icon as shown in the Figure 2-28, select the Properties. Figure 2-19 step 2. Select Device Manager as shown in Figure 2-29, then select Continue in the next screen.
SMC9452TX-2 step 3. Gigabit PCI Ethernet Adapter User Guide Right-click the adapter icon “Realtek RTL8169/8110 Family Gigabit Ethernet NIC”, and select “Update Driver Software…” to proceed. Figure 2-21 step 4. Select “Browse my computer for driver software” to install the software.
SMC9452TX-2 step 5. Gigabit PCI Ethernet Adapter User Guide Click the “Let me pick from a list of device drivers on my computer” in the next screen. Figure 2-23 step 6. Click “Have Disk…” in the next screen (shown in Figure 2-23).
SMC9452TX-2 step 7. Gigabit PCI Ethernet Adapter User Guide After that, select “Browse…” to locate the driver in the next screen. Figure 2-25 step 8. Locate the appointed driver as shown in Figure 2-35, click Open. Figure 2-26 ) Note: Vista X32 is designed for the Vista of 32bit, Vista X64 is designed for the Vista of 64bit, please select according as you need.
SMC9452TX-2 step 9. Gigabit PCI Ethernet Adapter User Guide After that, you will see the next screen (shown in Figure 2-36), click OK. Figure 2-27 ) Note: Assuming D is the letter of your CD-ROM drive. step 10. Select the model of the Card as shown in Figure 2-37, then click Next.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide step 11. After that, the installation will proceed as shown in Figure 2-38. Figure 2-29 ) Note: During the installation, you will see the warning box as shown in Figure 2-39, please select “Install this driver software anyway” to proceed.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide step 12. Finally, the installation will complete, you will see the next screen below, click Close to complete.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide 2.3 Enable Wake on LAN function This function allows a remote station “wake” your computer when it is in Standby or Hibernate mode or after shutdown. To enable WOL (take the configuration in Windows XP for example): a) Right click “My Computer” icon on the desktop and select “Properties”. b) Select “Hardware” and then “Device Manager” in the next screen.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide c) Right click “SMC9452TX-2 Gigabit Ethernet PCI Adapter”, and then select “Properties” d) Select the Advance title on the next advanced configure page, then highlight the Wake-On-Lan After Shutdown item and set the value as Enable.
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide ) Note: 1) The name of this Wake-On-Lan After Shutdown function is system-dependent, and it may be located in a category heading titled such as “Power Management”. See your computer’s user guide for more information regarding the BIOS Setup utility and BIOS settings. 2) A Magic Packet Tool is needed on the PC to remotely wake up WoL enabled computer on Shutdown mode (which is not needed on Sleep, Standby or Hibernate mode).
SMC9452TX-2 Gigabit PCI Ethernet Adapter User Guide Appendix A: Specifications Normal Interface Standards 32-bit PCI IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.ab 1000Base-T Access Protocol CSMA/CD Connector one 10/100/1000M Auto-Negotiation RJ45 port Novell NetWare3.x, 4.x, 5.
SMC9452TX-2