User Manual

ManualsBrandsSMC Networks ManualsElectronicsHome Siren Repeator

SMC Wireless Siren Zi

bee Ran

e Extender

Guide

2011 SMC Networks Page 1

I/M SMCSRXX-Z rev. 1.0

7/6/11

1 Models

The SMC Range Extender comes in two versions:

¾ SMCSR01-Z (North American version) ⎯

includes an Electrical Outlet Mounting Tab

(see Figure 2 on page 2)

¾ SMCSR01-Z CA (Canadian version) ⎯ no

provisions for securing device to an electrical

outlet

2 Parts List

¾ Battery Cover and Screw

¾ (2) rubber pads

¾ Battery

¾ Tamper Switch

NA version only:

¾ (3) plastic washers

¾ Electrical outlet screw

3 Package Contents

The package comes with a wall-mounting kit

containing 1 SMCSR01-Z and 2 tamper button

rubber pads. A lithium polymer rechargeable

battery is located inside the battery

compartment. The NA version includes 3 plastic

washers and a longer electrical outlet screw.

4 Specifications

Input Voltage: 110 VAC to 240 VAC 60 Hz

Peak Input Amp: 1A

Max Wattage: 20W

Power Limited Peak Output

Voltage:

Power Limited Peak Output

Amp:

Backup Battery Duration: >24 hrs

Nominal Battery Voltage

Range:

3.3V to 4V

Maximum Battery Voltage: 4.2V

Operating Temperature:

32°F to 104°F

(0°C to 40°C)

Storage Temperature:

14°F to 140°F

(-10°C to 60°C)

Battery Storage

Temperature:

-20°C to 60°C (1 week max)

-20°C to 45°C (3 week max)

-20°C to 20°C (1 year max)

Recommended Battery

Storage Temperature:

20°C +/- 2°C

Operating Relative Humidity: 10% to 90% noncondensing

Storage Relative Humidity: 5% to 95% noncondensing

Enclosure Dimensions: 3.81"L x 2.16"W x 1.58 H

(97 mm x 55 mm x 40.3 mm)

Max Volume: >85dB per UL measurement

Compatible Control Unit(s): RB5701-Z XXX

5 Key Components

Congratulations on purchasing your SMC Siren Zigbee Range Extender

The SMC Wireless Siren Zigbee Range Extender is a multipurpose fire and burglar alarm signaling device that performs two main functions in the SMC home-security product

lineup. It emits sound at levels greater than 85dB, loud enough to provide an audible alert and scare intruders. It also increases the range of your RB5701-Z SMA Gateway

wireless remote controls, motion sensors, and security products by boosting and retransmitting the RF signals it receives from those products.

Green, Red

Amber Status

LEDs

White LED

Figure 1. Front View

continued on next pag

Summary of content (7 pages)

PAGE 1
SMC Wireless Siren Zigbee Range Extender Guide Congratulations on purchasing your SMC Siren Zigbee Range Extender The SMC Wireless Siren Zigbee Range Extender is a multipurpose fire and burglar alarm signaling device that performs two main functions in the SMC home-security product lineup. It emits sound at levels greater than 85dB, loud enough to provide an audible alert and scare intruders.
PAGE 2
SMC Wireless Siren Zigbee Range Extender Guide Electrical Outlet Mounting Tab (NA version only) AC Receptacle where they may short-circuit each other or be short-circuited by conductive materials. DO NOT expose the battery to heat or fire. Avoid storage in direct sunlight DO NOT subject the battery to mechanical shock. DO NOT use any other charger other than the one built into the SMCSR01-Z. Tamper Switch DO NOT use any other battery that is not designed for use with this product.
PAGE 3
SMC Wireless Siren Zigbee Range Extender Guide 7 Selecting a Location The Range Extender lets you extend the range of your home security system to accommodate longer distances and broaden your security coverage. As a result, select a location that has average signal strength and resides between the TouchScreen and the furthest sensor, such as a gameroom or bedroom, to boost the wireless signal strength for sensors located furthest from the TouchScreen.
PAGE 4
SMC Wireless Siren Zigbee Range Extender Guide D. Remove the cover and connect the battery to the battery connector. Insert the battery plug into the pins so that the wire colors are arranged as shown in the picture below. 9 Adding the Siren A. At the TouchScreen Home screen, tap the B. E. The Status LED flashes green when the battery is connected. This means that the device is ready to be added to a TouchScreen. Note: If the Status LED does not flash green, the device may not be defaulted.
PAGE 5
SMC Wireless Siren Zigbee Range Extender Guide C. Toggle the Disabled/Enabled button to Disabled by tapping it. This prevents your test alarm from being sent to the central monitoring station. D. E. C. If the TouchScreen reports a Tamper trouble or A/C power trouble for the device, be sure it is pushed all the way into the outlet, so the tamper switch is pressed against the wall.
PAGE 6
SMC Wireless Siren Zigbee Range Extender Guide 13 Modifying the Details of the Range Extender Installers or customers can change the label the system uses to reference a siren and differentiate it from other devices. A. At the TouchScreen Home screen, tap the Settings app. B. On the Settings screen, use the keypad to enter the a valid key pad code. C. At the Technician Settings menu, select Home Devices > Sirens > Modify Siren. The Modify Siren screen appears. D.
PAGE 7
SMC Wireless Siren Zigbee Range Extender Guide ¾ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules.