Datasheet

ManualsBrandsSMC Networks ManualsAccess PointsSMC Networks WAP5110

www.smc.com

www.smc-asia.com

Connect Your World ...

Switches | Wireless | Broadband | Carrier Ethernet | Network Management

WAP5110

802.11n Dual-Band Wireless Access Point

Product Overview

The WAP5110 is an indoor 802.11a/b/g/n dual-band, dual-radio enterprise AP with a 2x2 MIMO antenna configuration.

Through its Gigabit Ethernet port the 802.11n dual-band wireless AP can connect to the backbone network. The WAP5110

supports 802.3af PoE, which enables the AP to be powered remotely by a PoE switch. An AC power adapter option is also

included for locations where PoE is not available.

Key Features and Benefits

Wireless 802.11n Technology

Using 802.11n MIMO (Multiple Input Multiple Output)

wireless technology, the AP supports two transmitting

and two receiving antennas that extend range and

increase the throughput by up to nine times that of

existing Wi-Fi.

Full Management Capabilities

The WAP5110 supports Simple Network Management

Protocol (SNMP v1/v2c/v3), including MIB II and MIB I.

The IEEE 802.1X authentication protocol supports

Extensible Authentication Protocol (EAP) MD5, Transport

Layer Security (TLS), Protected EAP (PEAP), Tunneled

TLS (TTLS), EAP-SIM, and EAP-AKA.

Application Diagram

Advanced Traffic Management

Support for up to sixteen Virtual Access Point (VAP)

interfaces per radio, which allows traffic to be separated for

different user groups within the same service area. Each radio

can support up to 100 wireless clients, shared between all

VAPs, whereby the clients associate with each VAP in the

same way as they would with physically separate APs. This

means that each VAP can be configured with its own Service

Set Identification (SSID), security settings, VLAN

assignments, and other parameters, allowing the AP to serve

a diverse range of client needs from a single unit.

Dual-Band Access Point

Easy on your budget and simple to install, the AP uses

dynamic rate shifting to automatically match the best

connection speed, keeping users connected to the network

even while roaming.

WDS Links

Between Access Points

VAP 0

WDS STA Mode

VAP 2

AP Mode

VAP 0

WDS STA Mode

VAP 2

AP Mode

VAP 0

WDS AP Mode

VAP 1

AP Mode

VAP 0

WDS STA Mode

VAP 1

WDS AP Mode

VAP 0

WDS STA Mode

VAP 1

WDS AP Mode

VAP 1

AP Mode

Network

Core

Summary of content (2 pages)

PAGE 1
WAP5110 802.11n Dual-Band Wireless Access Point Product Overview The WAP5110 is an indoor 802.11a/b/g/n dual-band, dual-radio enterprise AP with a 2x2 MIMO antenna configuration. Through its Gigabit Ethernet port the 802.11n dual-band wireless AP can connect to the backbone network. The WAP5110 supports 802.3af PoE, which enables the AP to be powered remotely by a PoE switch. An AC power adapter option is also included for locations where PoE is not available. Key Features and Benefits Wireless 802.
PAGE 2
Features Physical Features One 10/100/1000BASE-T Gigabit Ethernet (RJ-45) port with 802.3af-compliant Power over Ethernet (PoE) support One console port with an RJ-45 connector Two LEDs: Power/Diag, WLAN1/WLAN2/LAN Four embedded omni antennas PoE 802.3af compliant Standards IEEE 802.11n 2.4 GHz and 5.0 GHz IEEE 802.11a 5.0 GHz IEEE 802.11b/g, 2.4 GHz IEEE 802.3, IEEE 802.3u, IEEE 802.3ab IEEE 802.3af Power over Ethernet (PoE) IEEE 802.