INSTRUCTION MANUAL GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS
Contents 1. Description of the controls________________________________16 2. Troubleshooting _______________________________________25 Thank you for choosing one of our products. You are advised to read this manual carefully; it contains all the information you need about the right conditions for the proper, safe use of your dishwasher.
User instructions 1. Description of the controls 1.1 Front panel All the dishwasher controls are grouped on the front panel. 1 ON/OFF BUTTON 2 SELECTION PROGRAM BUTTONS (P1…P5) 3 3/1 OPTION BUTTON 4 DELAY PROGRAM BUTTON 5 START/STOP BUTTON 6 POWER ON LIGHT 7 PROGRAM PHASE INDICATOR LIGHTS 8 INFORMATION DISPLAY 9 RECESSED DOOR HANDLE 1.2 Information display The dishwasher is equipped with a practical DISPLAY which provides information on the programmed dishwasher functions.
User instructions PROGRAMME, NUMBER & SYMBOL LOAD CROCKERY AND CUTLERY 1 SOAK Pans and dishes awaiting a further wash 2 QUICK Dishes with light dirt 3 ECO (*) EN 50242 Wash immediately after use for dishes with normal dirt 4 AUTO 40-60 Wash immediately after use for dishes with normal dirt 5 INTENSIVE Very dirty pans and dishes, even with dried-on dirt 6 DELICATE Dishes with normal dirt 7 BIO Dishes with normal dirt 8 AUTO 60-70 Normally soiled dishes, including dried-on residue 9
User instructions TABLE FOR CERTIFICATION BODIES Reference standard Reference program Load Type of detergent Amount of detergent Rinse aid setting EN 50242 ECO 10 place-settings B 25 g Depending on the model 3/4 or 4/6 1.3 Washing programs The dishwasher is equipped with a control panel and an INFORMATION DISPLAY (8) from which it is possible to carry out all the power switchon, switch-off and programming operations. Before starting a washing program make sure that: • The water supply tap is open.
User instructions PROGRAMMING In this dishwasher model all the programming operations are possible only with closed door. With open door, on the DISPLAY (8) will appear the symbols -- and the PILOT LIGHT PROGRAMS (7) remains out. SELECTION PROGRAM The program selection is possible through the relative buttons (2).
User instructions INTERRUPTING A PROGRAM In order to interrupt a running program it is necessary: • to press the START/STOP (5) for some seconds until when the writting “Time to end” remains lit on the display (confirmation beep).
User instructions DELAYING THE PROGRAM (available in all programs except the soak program) The PROGRAM DELAY button (4) can be pressed to delay the start of the program by up to 12 hours. This means that the dishwasher can be operated at the time of day of your choice. The first time the PROGRAM DELAY button (4) is pressed the display will show 12 hours, the maximum delay time before the program will start.
User instructions TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT • • • • • • Always try to run the dishwasher fully loaded. Do not wash the dishes in running water. Use the washing program that is most appropriate for each type of load. Do not carry out any preliminary rinsing. If available, connect the dishwasher to a hot water supply up to 60°C. When possible, skip the drying cycle by leaving the door open when the washing cycle is complete; the air and the residual heat will dry the dishes perfectly.
User instructions ADDITIONAL FUNCTIONS (available in all programs except the soak program) The electronic control system allows personalizing the machine use directly through a programming procedure not directly accessible that allows: regulate water hardness level. Depending on model, the setting may be made electronically or by means of a selector switch. ELECTRONIC SETTING To access the programming environment, the appliance must be turned on with the door closed.
User instructions SWITCH SETTING The dishwasher is equipped with an device for the user to adjust the water softening system according to the hardness of the water supply. The setting switch is inside the plastic locking ring located on the righthand side, inside the dishwasher. WATER HARDNESS TABLE WATER HARDNESS German Degrees (°dH) French Degrees (°dF) 0-4 5 - 15 16 - 23 24 - 31 32 - 47 48 - 58 0-7 8 - 25 26 - 40 41 - 60 61 - 80 81 - 100 SETTING Setting N. 1 NO SALT Setting N. 1 Setting N.
User instructions 2. Troubleshooting The dishwasher is equipped with a self-diagnostics system that is capable of detecting and signalling a number of possible faults. TABLE OF FAULTS DETECTED BY THE SELF-DIAGNOSTICS SYSTEM FAULT DESCRIPTION Acquastop failure E1 The anti-flooding system has been activated (for the relevant models only). The system is tripped in case of water leaks. Contact the aftersales service.
User instructions FAULT DESCRIPTION Turbine flow-regulator malfunction (for the relevant models only) The appliance is not able to "measure" the amount of water loaded accurately. Interrupt the program and switch off the dishwasher. Switch the dishwasher back on, program it again and start the washing cycle. If the problem persists, contact the after-sales service. E7 Alternate washing system malfunction Interrupt the program and switch off the dishwasher.
INSTRUCTION MANUAL WARNINGS AND RECOMMENDATIONS, GUIDE FOR THE USE OF BASKETS AND FOR CLEANING DISHWASHERS
Contents 1. Safety and operating instructions ___________________________ 20 2. Installation and hook-up __________________________________ 22 2.1 Water supply connection _____________________________________________________ 22 2.2 Electrical connection ________________________________________________________ 23 3. Operating instructions ____________________________________ 24 3.1 3.2 3.3 3.
Safety instructions 1. Safety and operating instructions THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER. BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REGULATIONS IN FORCE.
Safety instructions IN THE EVENT OF A FAULT, DISCONNECT THE DISHWASHER FROM THE ELECTRICAL POWER SUPPLY AND SHUT OFF THE WATER TAP. THEN CALL IN A QUALIFIED TECHNICIAN. DO NOT USE APPLIANCES WHICH HAVE BEEN DAMAGED DURING TRANSIT! IF IN DOUBT, CONSULT YOUR DEALER. THE APPLIANCE MUST BE INSTALLED AND CONNECTED IN ACCORDANCE WITH THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER OR BY A QUALIFIED TECHNICIAN. THE APPLIANCE IS INTENDED FOR USE BY ADULTS.
Installation instructions 2. Installation and hook-up Remove the polystyrene basket retainers. Position the appliance in the desired place of installation. The back or sides of the dishwasher may be placed up against walls or other furniture units. If the dishwasher is installed near a heat source, fit the special insulating panel to prevent overheating and malfunction of the appliance.
Installation instructions The dishwasher can also be connected to a hot water supply not exceeding 60°C. Supplying the appliance with hot water cuts down the washing time by approximately 20 minutes, but slightly reduces its effectiveness. Make the connection to the domestic hot water supply using the same procedure described for connecting to the cold water supply.
User instructions 3. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: • Adjust the water softening system; • Add the regenerating salt; • Add the rinse aid and detergent. 3.1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time.
User instructions 3.2 Using the rinse aid and detergent dispensers The detergent and rinse aid dispensers are situated on the inner part of the door: the detergent dispenser is on the left, and the rinse aid dispenser is on the right. With the exception of the SOAK program, before every washing cycle it is necessary to add the required amount of detergent to the detergent dispenser. The rinse aid, on the other hand, should only be added as required.
User instructions ADDING THE DETERGENT To open the detergent dispenser cap, lightly press the button P. Add the detergent and close the cap carefully. During the washing cycle, the dispenser will be opened automatically. • • • • • • • • When a SUPER program is selected, in addition to the normal dose of detergent, it is necessary to add an additional amount inside compartment G or H. Use only detergents specially formulated for dishwashers.
User instructions 3.3 General warnings and recommendations Before using the dishwasher for the first time, it is advisable to read the following recommendations concerning dish types to be washed and their loading. There are generally no constraints on the washing of domestic dishes, but in certain cases it is necessary to take their characteristics into account. Before loading the dishes into the baskets it is necessary to: • remove coarse food remains: e.g. bones, fish-bones, etc.
User instructions 3.4 Using the baskets The dishwasher has a capacity of 10 place-settings, including serving dishes. EN 50242 STANDARD LOADS FOR CERTIFICATION BODIES LOWER BASKET UPPER BASKET LOWER BASKET The lower basket receives the full force of the lower spray arm, and should therefore be used for the “toughest” items with a heavier degree of soiling.
User instructions CUTLERY BASKET The cutlery should be arranged in an orderly manner inside the basket, with the handles pointing downwards. Take care during loading to avoid injury from the knife blades. The basket is suitable for all types of cutlery, except those long enough to interfere with the upper spray arm. Ladles, wooden spoons and cooking knives can be placed in the upper basket, making sure that the knife blades do not protrude from the basket.
User instructions LOADING THE UPPER BASKET Load plates facing forward; cups, bowls etc. must always be facing downwards. The left side of the basket can be loaded with cups and glasses on two levels. On the right plates and saucers can be slotted verticalli into the forks. Loading examples: ADJUSTING THE UPPER BASKET The upper basket can be adjusted in two positions, according to the user’s needs and according to the height of the dishes in the lower basket.
User instructions 4. Cleaning and maintenance Before carrying out any work, always disconnect the appliance from the electrical power supply. 4.1 General warnings and recommendations Avoid the use of acidic or abrasive detergents. Clean the outer surfaces and door-lining of the dishwasher regularly using a soft cloth moistened with water or with a normal detergent suitable for painted surfaces. Clean the door gaskets with a damp sponge.
User instructions CLEANING THE FILTER UNIT • • • • The central filter H should be inspected regularly and cleaned if necessary. To remove it, take hold of the handle, turn anti-clockwise and lift. Press the central filter H from below to extract it from the micro-filter. Separate the two parts of the plastic filter by pressing the body of the filter in the zone shown by the arrows. Remove the central filter by lifting it.
User instructions TROUBLESHOOTING MINOR PROBLEMS In some cases it is possible to remedy minor problems by referring to the following instructions: If the program fails to start, check that: • • • • the dishwasher is connected to the electrical power supply; there is no power failure; the water tap is open; the dishwasher door is properly closed.
User instructions TECHNICAL DATA Width Depth measured flush with the outer edge of the control panel Height Capacity Water supply pressure Electrical characteristics 34 447 ÷ 449 mm Free standing: 600 mm Semi-integrated: 590 mm - Fully integrated: 570 mm Free standing from 850 mm to 870 mm Semi-integrated and fully integrated: from 820 mm to 870 mm 10 Standard place settings Min. 50 – max. 900 KPa (min. 0.5 – max.
115 125 135 145 155 Misurarel’altezzadelpannellocomandi;farecoinciderel’indicerelativo a talevaloreconilprofilosuperioredellaporta inlegno;tracciare ilposizionamentodegliagganciporta. Measurethe height ofthecontrolpanel;bringthemarkrelatingtothisvalueintolinewith thetopedgeofthewoodendoor;markthepositionsofthedoorconnections. Measurerlahauteurdupanneaudecommandes;fairecoïnciderl’indexrelatifàcettevaleuravecleprofilsupérieur delaporteenbois;tracerlepositionnementdescrochetsdelaporte.