INSTRUCTION MANUAL GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS
Contents 1. Description of the controls________________________________16 2. Troubleshooting _______________________________________25 Thank you for choosing one of our products. You are advised to read this manual carefully; it contains all the information you need about the right conditions for the proper, safe use of your dishwasher.
User instructions 1. Description of the controls 1.1 Front panel All the dishwasher control are grouped on the front panel. 1 ON/OFF BUTTON 2 SELECTION PROGRAMS BUTTONS (P1...
User instructions PROGRAM SELECTION TYPE AND GRADE DIRT PROGRESS PROGRAM DURATION CONSUMPTION MINUTES (2) WATER LITRES (1) POWER KWh (2) SOAK PANS AND DISHES IN WAITING OF COMPLETING THE LOAD Cold prewash 9' 5 0,02 QUICK DISHES NOT MUCH DIRTY AND WITH "FRESH DIRT" WITHOUT RESIDUAL DRY Wash at 38°C Cold rinse Rinse at 58°C 45' 13 0,70 PANS AND DISHES NOT VERY DIRTY BUT WITH DRY RESIDUALS Wash at 55°C Cold rinse Rinse at 66°C Dry (**) (**) (**) ECO (*) 175' (AAA) 125' (AAB) 90' (BA
User instructions TABLE FOR CERTIFICATION BODIES Reference standard Reference program Load Type of detergent Amount of detergent Rinse aid setting EN 50242 (*) Program ECO (P3) 10 place-settings B 25 g 5/6 1.2 Washing programs The dishwasher is equipped with a control panel, described in chapter "1. Description of the controls", from which it is possible to carry out all the power switch-on, switch-off and programming operations.
User instructions PROGRAMMING In this model of dishwasher, all programming procedures can only be carried out with the door closed. As long as the door is open, the PROGRAMS lights (6) and PHASES/PROGRAM lights (8) will remain off. SELECTION PROGRAM The program selection is possible through the relative buttons (2). When the button relating to the program required is pressed, the relative light will come on to confirm the operation.
User instructions END PROGRAM When the program finishes, a buzzer sounds briefly and all the PHASES/PROGRAM lights (8) flash. Press any of the SELECTION PROGRAMS buttons (2), stops the light flashins, and the dishwasher is now ready to perform a new cycle; opening and shutting the door or switching the appliance off and on has the same effect.
User instructions ANNULLING A PROGRAM To annul the program in progress, it must first be interrupted (see “INTERRUPTION OF A PROGRAM”). Now press buttons P1+P2 simultaneously and the first three program lights will come on. In case that the door is opened during the operation, to the next door closing it is going to be necessary to start the program as shown in paragraph “START PROGRAM”. The program will resume from the point in which it was interrupted.
User instructions To set the delay once the program has started, proceed as follows. If the program you wish to carry out is the same as the one already in progress: • • • • • press the START/PAUSE button (4) for a few seconds, until the PHASES/PROGRAM lights (8) come on; annul the program in progress (see relative section) and wait for the cycle to come to an end; select the program again; select the delay required; press the START/PAUSE button (4) to start the new program.
User instructions TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT • • • • • Always try to run the dishwasher fully loaded. Do not wash the dishes in running water. Use the washing program that is most appropriate for each type of load. Do not carry out any preliminary rinsing. If available, connect the dishwasher to a hot water supply up to 60°C. TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENT The phosphates contained in dishwasher detergents are harmful to the environment.
User instructions ADJUSTING THE WATER SOFTENING SYSTEM The dishwasher is equipped with an device for the user to adjust the water softening system according to the hardness of the water supply. The setting switch is inside the plastic locking ring located on the righthand side, inside the dishwasher. WATER HARDNESS TABLE WATER HARDNESS German Degrees (°dH) French Degrees (°dF) 0-4 5 - 15 16 - 23 24 - 31 32 - 47 48 - 58 0-7 8 - 25 26 - 40 41 - 60 61 - 80 81 - 100 SETTING Setting N. 1 NO SALT Setting N.
User instructions 2. Troubleshooting In case of a malfunction, the dishwasher will identify the program by switching on a combination of lights. When an alrm is present, all the PROGRAM lights (6) come on, while the PHASES/PROGRAM lights (8) identify the error code: CODE PHASES LIGHTS DESCRIPTION E1 The anti-flooding system (if installed) has been tripped. E2 The system which limits the water level inside the dishwasher (safety unit) has been tripped. E3 The appliance cannot heat the water.
INSTRUCTION MANUAL WARNINGS AND RECOMMENDATIONS, GUIDE FOR THE USE OF BASKETS AND FOR CLEANING DISHWASHERS
Contents 1. Safety and operating instructions __________________________28 2. Installation and hook-up _________________________________31 3. Operating instructions ___________________________________35 4. Cleaning and maintenance _______________________________46 Thank you for choosing one of our products. You are advised to read this manual carefully; it contains all the information you need about the right conditions for the proper, safe use of your dishwasher.
Safety instructions 1. Safety and operating instructions THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER. BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REGULATIONS IN FORCE.
Safety instructions OBSOLETE APPLIANCES MUST BE RENDERED UNUSABLE. CUT OFF THE MAINS POWER CORD AFTER UNPLUGGING IT FROM THE WALL OUTLET, AND MAKE SAFE ANY COMPONENTS WHICH MIGHT BE DANGEROUS FOR CHILDREN (LOCKS, DOORS, ETC.). THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE).
Safety instructions LEANING OR SITTING ON THE DISHWASHER DOOR WHEN OPEN MAY CAUSE THE APPLIANCE TO OVERTURN, PUTING PEOPLE AT RISK. NEVER LEAVE THE DISHWASHER DOOR OPEN; PEOPLE MIGHT TRIP OVER IT. DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE THE DISHES OR DISHWASHER AT THE END OF THE WASHING PROGRAM AND BEFORE THE DRYING CYCLE. KNIVES OR OTHER SHARP-ENDED COOKING UTENSILS MUST BE PLACED IN THE CUTLERY BASKET BLADE-DOWN, OR LAID HORIZONTAL IN THE TOP BASKET.
Installation instructions 2. Installation and hook-up Remove the polystyrene basket retainers. Position the appliance in the desired place of installation. The back or sides of the dishwasher may be placed up against walls or other furniture units. If the dishwasher is installed near a heat source, fit the special insulating panel to prevent overheating and malfunction of the appliance.
Installation instructions 2.1 Water supply connection Preventing the risk of clogging or damage: if the water pipe is new or has not been used for a long time, before connecting to the water supply check that the water is clear and free of impurities, to prevent damage to the appliance. The dishwasher must always be connected to the water system with new hoses; old or used hoses must never be reused.
Installation instructions 2.2 Electrical connection and precautions CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH THE RATINGS ON THE NAME PLATE OF THE APPLIANCE POSITIONED ON THE INNER EDGE OF THE DOOR. THE PLUG ON THE SUPPLY CORD AND THE CORRESPONDING SOCKET OUTLET MUST BE OF THE SAME TYPE AND MEET THE REGULATIONS IN FORCE. THE PLUG MUST BE ACCESSIBLE AFTER INSTALLATION. NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD.
Installation instructions WHEN CLEANING AND MAINTAINING THE APPLIANCE: BEFORE CARRYING OUT ANY WORK, ALWAYS UNPLUG THE APPLIANCE FROM THE ELECTRICAL SUPPLY OR SWITCH OFF THE ALL-POLE DISCONNECTION DEVICE. FOR GREAT BRITAIN ONLY: THIS APPLIANCE MUST BE EARTHED. Fuse replacement If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S.T.A. approved fuse to BS 1362 type and proceed as follows: 1. 2. 3.
User instructions 3. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: • • • Adjust the water softening system; Add the regenerating salt; Add the rinse aid and detergent. 3.1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time.
User instructions • Do not use table salt as it contains insoluble substances which, over time, may damage the water softening system. • When necessary, refill the regenerating salt container before starting the washing program. In this way, the excess saline solution will be immediately removed by the water; the prolonged presence of salt water inside the tank may lead to corrosion.
User instructions ADDING THE RINSE AID The rinse aid helps the dishes dry faster and prevents the formation of scale deposits and staining; it is automatically added to the water during the final rinse cycle, from the container situated on the inner side of the door. To add rinse aid: • Open the door. • Rotate the container cap anticlockwise by ¼ of a turn and remove it. • Add the rinse aid until the container is full (approximately 140 cc).
User instructions ADDING THE DETERGENT To open the detergent dispenser cap, lightly press the button P. Add the detergent and close the cap carefully. During the washing cycle, the dispenser will be opened automatically. • When a program with hot prewash is selected (see program table), extra detergent must be placed in the cavity G/H (depending on models). • Use only detergents specially formulated for dishwashers. For optimal washing results it is important to use a good quality detergent.
User instructions • The market offers liquid and powder detergents with differing chemical compositions, which may contain phosphates, or be phosphate-free but contain natural enzymes. - Detergents containing phosphates are more effective against grease and starch at temperatures above 60°C. - Enzyme detergents, on the other hand, are also effective at lower temperatures (from 40 to 55°C) and are more easily biodegradable.
User instructions 3.3 General warnings and recommendations Before using the dishwasher for the first time, it is advisable to read the following recommendations concerning dish types to be washed and their loading. There are generally no constraints on the washing of domestic dishes, but in certain cases it is necessary to take their characteristics into account. Before loading the dishes into the baskets it is necessary to: • remove coarse food remains: e.g. bones, fish-bones, etc.
User instructions Items which are not dishwasher-safe: • • • • • • • • Wooden dishes, pots or pans: these may be damaged by the high washing temperatures. Handcrafted items: these are rarely suitable for washing in a dishwasher. The relatively high water temperatures and the detergents used may damage them. Plastic dishes: heat resistant plastic dishes must be washed in the upper basket. Dishes and objects in copper, tin, zinc or brass: these tend to stain.
User instructions 3.4 Using the baskets The dishwasher has a capacity of 10 place-settings, including serving dishes. EN 50242 STANDARD LOADS FOR CERTIFICATION BODIES LOWER BASKET UPPER BASKET The upper basket must be set in the low position. LOWER BASKET The lower basket receives the full force of the lower spray arm, and should therefore be used for the “toughest” items with a heavier degree of soiling.
User instructions LOADING THE LOWER BASKET Carefully load flat plates, soup plates, dessert and serving dishes, positioning them vertically. Pots, pans and their covers must be loaded upside down. When loading soup plates and dessert bowls, be sure to leave a gap between them. Loading examples: CUTLERY BASKET The cutlery should be arranged in an orderly manner inside the basket, with the handles pointing downwards. Take care during loading to avoid injury from the knife blades.
User instructions UPPER BASKET It is recommended to load the upper basket with small- or medium-sized items such as glasses, small plates, tea or coffee cups, shallow bowls and light objects made from heat resistant plastic. If the upper basket is used in the lowermost position, it can also be loaded with serving dishes, provided they are only slightly soiled. The basket is equipped with two tip-up cutlery supports which can be raised or lowered as required. See illustrations below.
User instructions ADJUSTING THE UPPER BASKET The upper basket can be adjusted in two positions, according to the user’s needs and according to the height of the dishes in the lower basket. Proceed as follows: • • • • turn the retainer E on both runners, right and left, through 90°; remove the basket; lift the basket and fit the smaller pairs of wheels in the runners; return the retainers E to their original position.
User instructions 4. Cleaning and maintenance Before carrying out any work, always disconnect the appliance from the electrical power supply. 4.1 General warnings and recommendations Avoid the use of acidic or abrasive detergents. Clean the outer surfaces and door-lining of the dishwasher regularly using a soft cloth moistened with water or with a normal detergent suitable for painted surfaces. Clean the door gaskets with a damp sponge.
User instructions CLEANING THE SPRAY ARM, TRAVELLING VERSION To remove the TRAVELLING spray arm, take hold of it and raise it to release both the spray arm and the pipe from the tank, then detach the spray arm from the pipe. Wash both the pipe and the spray arm in running water, re-attach the spray arm to the pipe and return the assembly to the seat provided in the tank.
User instructions GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE: • • • The filters should be cleaned under running water using a stiff brush. It is essential to thoroughly clean the filters according to the above instructions: the dishwasher cannot function if the filters are clogged. Carefully replace the filters in their seats, to avoid damaging the wash pump. PROLONGED DISUSE: • • • • • Run the soak program twice in succession. Unplug the power cord from the socket.
User instructions If the dishes are not being cleaned properly, check that: • • • • • • • the correct amount of detergent has been added; there is regenerating salt inside the special container; the dishes are being loaded correctly; the selected program is suitable for the dish types and their degree of soiling; all the filters are clean and positioned correctly; the spray arm nozzles are not obstructed; there is no object obstructing the rotation of the spray arms.
User instructions TECHNICAL DATA Width Depth measured flush with the outer edge of the control panel Height Capacity Water supply pressure Electrical characteristics 447 ÷ 449 mm Free standing: 600 mm Semi-integrated: 590 mm - Fully integrated: 570 mm Free standing from 850 mm to 870 mm Semi-integrated and fully integrated: from 820 mm to 870 mm 10 Standard place settings min. 0,05 - max. 0,9 MPa (min. 0.5 – max.
115 125 135 145 155 Misurarel’altezzadelpannellocomandi;farecoinciderel’indicerelativo a talevaloreconilprofilosuperioredellaporta inlegno;tracciare ilposizionamentodegliagganciporta. Measurethe height ofthecontrolpanel;bringthemarkrelatingtothisvalueintolinewith thetopedgeofthewoodendoor;markthepositionsofthedoorconnections. Measurerlahauteurdupanneaudecommandes;fairecoïnciderl’indexrelatifàcettevaleuravecleprofilsupérieur delaporteenbois;tracerlepositionnementdescrochetsdelaporte.