INSTRUCTION MANUAL GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS
EN CONTENTS CONTENTS 1 INTRODUCTION ........................................................................................ 3 2 DESCRIPTION AND USE OF THE CONTROLS .......................................... 5 2.1 Upper panel ............................................................................................... 5 2.2 Setting the washing program and switching on and off............................... 6 2.2.1 Switching on .....................................................................
EN 2 Rev 0.
EN INTRODUCTION 1 INTRODUCTION Thank you for choosing one of our products. To use this dishwasher correctly and safely, please read this manual carefully. The manual is divided into sections giving you a step-by-step guide to all your appliance’s functions. The texts are easy to understand and are complete with detailed illustrations. This user-friendly manual will provide answers to all your questions about use of the dishwasher.
EN INTRODUCTION Symbols used in this manual (see tab. 1-01) DANGER. This symbol highlights information and warnings which, if not observed, may compromise personal safety or damage the appliance. This symbol highlights general information and warnings. Tab. 1-01 4 Rev 0.
EN USER INSTRUCTIONS 2 DESCRIPTION AND USE OF THE CONTROLS 2.1 Upper panel All the dishwasher controls are grouped on the upper panel (see fig. 2-01). The dishwasher can only be switched on, programmed, switched off, etc. with the door open. A brief description (see tab. 2-01) of the various controls on the upper panel is given below. Fig. 2-01 1 2 3 4 5 6 7 8 On/off button Press to power the appliance.
EN USER INSTRUCTIONS 2.2 Setting the washing program and switching on and off The dishwasher is equipped with a control panel (see fig. 2-02) which is used to program the appliance and switch it on and off. Fig. 2-02 To select the most suitable program for the dishes to wash, consult the following table which specifies the most appropriate type of washing sequence depending on the kind of dishes and how dirty they are (see tab. 2-02). 6 Rev 0.
EN USER INSTRUCTIONS PROGRAM NUMBER AND SYMBOL DISHES AND CUTLERY 1 Pans and dishes waiting Cold pre-wash for further washing RINSE CRYSTAL Immediate washing after use for moderately dirty dishes 3 NORMAL Immediate washing after use for normally dirty dishes 4 AUTO DELICATE Normally dirty dishes EXTREME WASH Very dirty pans and dishes (except delicate items) 2 5 ETL SANITATION LISTED PROGRAM SEQUENCE Wash at 45°C (113°F). Cold rinse. Rinse at 69°C (156.2°F). Dry. Cold pre-wash.
EN USER INSTRUCTIONS Only run the soak program with half loads. After using the above table to choose the most suitable washing cycle, program the appliance. Before starting a washing program, make sure that: • The water supply tap is open. • There is regenerating salt in the water softener tank (to add salt, see the instructions in the general manual). • The correct amount of detergent has been added to the dispenser (to add detergent, see the instructions in the general manual).
EN USER INSTRUCTIONS 2.2.4 Interrupting a program To interrupt the current program simply open the door of the dishwasher; to restart the program, simply close the door again. The program restarts from where it was interrupted. If it is necessary to open the door during the washing cycle, the program will be interrupted, the relative indicator light will continue to flash and a beep will indicate that the cycle has not terminated.
EN USER INSTRUCTIONS 2.2.7 Options PROGRAM DELAY The “Program delay” function delays the beginning of the washing program up to 9 hours from the moment in which programming takes place. This makes it possible to use the dishwasher at a certain time of day. Before programming a delay, open the door of the dishwasher, select the required washing program (see para 2.2 “Setting the washing program and switching on and off”). Select the day by pressing the Program delay button (ref. 7 fig.
EN USER INSTRUCTIONS 2.2.8 Switching off At the end of the program, the dishwasher emits a short beep and the indicator lights of the fourth and fifth program (ref. pr. 4, pr. 5 fig. 2-04) flash. Turn off the appliance by opening the door and pressing the on/off button (ref. 1 fig. 2-02). pr. 4 pr. 5 Fig. 2-04 2.3 Additional functions 2.3.1 Adjusting the water softener N.B.: a different washing program from soak must be used to make the following adjustment..
EN USER INSTRUCTIONS N.B.: the display indicates the water hardness adjustment and the program delay. A dot (.) after the number means that the water hardness adjustment is being displayed. If no dot (.) appears, the program delay is being displayed. Fig. 2-05 Water hardness table (see tab. 2-03) WATER HARDNESS French degrees (°F) American degrees grains/galls SETTING German degrees (°D) 0-4 0-7 0 - 4.5 0. 5 - 15 8 - 25 4.6 - 14.5 1. 16 - 23 26 - 40 14.6 - 23.5 2. 24 - 31 41 - 60 23.
EN USER INSTRUCTIONS 3 ENERGY SAVING AND ENVIRONMENTAL RESPECT Always try to run the dishwasher fully loaded. Do not wash the dishes under a running tap. Use the most suitable washing program for each type of load. Do not pre-rinse. If available, connect the dishwasher to a hot water system with a temperature of up to 60°C (140°F). • When possible, skip the drying cycle by opening the door after washing: the air and the residue heat will dry the dishes to perfection. • • • • • 3.
EN USER INSTRUCTIONS 4 REMOVING THE DISHES At the end of the washing program, wait at least 20 minute before removing the dishes in order to allow them to cool. To prevent any water droplets on the upper rack from falling onto the dishes in the lower rack, empty the lower rack first and then the upper one. 14 Rev 0.
EN USER INSTRUCTIONS 5 TROUBLESHOOTING The dishwasher can to signal a number of malfunctions by turning on various indicator lights, as described below (see following table): FAULT DESCRIPTION E1 Acquastop failure The anti-flooding system has tripped (only for models fitted with this feature). Activates in case of water leaks. Contact the technical assistance service. E3 Water heating malfunction The water is not heated or is incorrectly heated.
EN USER INSTRUCTIONS If an alarm situation occurs, the dishwasher interrupts the current program and signals the fault. • Alarms E1, E3, E4, immediately terminate the current program. • Alarms E5, E6 interrupt the current program and, after the problem has been eliminated, resume the cycle. To “reset” an alarm: • open or close the door, or switch the appliance on and back off again. At this point, the dishwasher can be programmed again.
EN CONTENTS Contents 1 INTRODUCTION ........................................................................................ 3 2 IMPORTANT SAFETY INSTRUCTION ......................................................... 5 3 INSTALLATION AND HOOK-UP ............................................................... 11 4 OPERATING INSTRUCTIONS .................................................................. 14 4.1 Using the water softening system ..........................................................
EN 2 Rev 0.
EN INTRODUCTION 1 INTRODUCTION Thank you for choosing one of our products. To use this dishwasher correctly and safely, please read this manual carefully. The manual is divided into sections giving you a step-by-step guide to all your appliance’s functions. The texts are easy to understand and are complete with detailed illustrations. Following the cleaning instructions provided here will keep dishwasher performance at peak levels in the long term.
EN INTRODUCTION Symbols used in this manual (see tab. 1-01) DANGER. This symbol highlights information and warnings which, if not observed, may compromise personal safety or damage the appliance. DANGER OF ELECTROCUTION. This symbol highlights information and warnings of an electrical nature which, if not observed, may compromise personal safety or damage the appliance. This symbol highlights general information and warnings. Tab. 1-01 4 Rev 0.
EN WARNINGS 2 IMPORTANT SAFETY INSTRUCTION (Save this instructions) THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER (INCLUDING THE “INSTALLATION” AND “DESCRIPTION OF CONTROLS” MANUALS, IF ATTACHED). BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REGULATIONS IN FORCE.
EN WARNINGS BEFORE PROCEEDING WITH INSTALLATION, DISCONNECT THE MAINS POWER SUPPLY FROM THE WORK AREA. DO NOT USE EXTENSION CORDS, ADAPTORS OR SHUNT CONNECTIONS IN ORDER TO AVOID THE POSSIBILITY OF OVERHEATING OR BURNING WITH CONSEQUENT FIRE HAZARD. DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF ON THE SHARP EDGES OF THE APPLIANCE; WEAR SAFETY GLOVES. THE APPLIANCE MUST BE PROVIDED WITH AN EARTH CONNECTION IN ACCORDANCE WITH THE ELECTRICAL SAFETY REGULATIONS IN FORCE.
EN WARNINGS ONLY USE RINSE-AID SPECIALLY FORMULATED FOR DOMESTIC DISHWASHERS. DO NOT INHALE OR SWALLOW DETERGENT AS THIS MAY CAUSE BURNS AND/OR PERMANENT DAMAGE TO THE NOSE, MOUTH AND THROAT, AND EVEN LEADING TO SUFFOCATION; KEEP DETERGENT AWAY FROM YOUR EYES. IF ONE OF THE ABOVE SITUATIONS OCCURS, SEEK MEDICAL ASSISTANCE IMMEDIATELY.
EN WARNINGS DO NOT INTRODUCE ITEMS IN HEAT-SENSITIVE PLASTI¬C, SUCH AS DISPOSABLE CUTLERY OR PLATES, AS THESE MAY BECOME DEFORMED. DO NOT WASH OBJECTS IN PLASTIC UNLESS THEY ARE MARKED “DISHWASHER PROOF” OR THE LIKE. FOR UNMARKED OBJECTS, FOLLOW THE INSTRUCTIONS OF THE MANUFACTURER; IF NO INFORMATION IS AVAILABLE, DO NOT WASH THESE OBJECTS IN THE DISHWASHER. DO NOT INTRODUCE ANIMALS INTO THE DISHWASHER.
EN WARNINGS KNIVES OR OTHER SHARP-ENDED COOKING UTENSILS MUST BE PLACED IN THE CUTLERY BASKET BLADE-DOWN, OR LAID HORIZONTAL IN THE UPPER RACK. TAKE CARE NOT TO CUT YOURSELF AND ENSURE THAT THEY DO NOT PROJECT FROM THE RACK. POSITION SHARP/POINTED OBJECTS SO AS TO PREVENT THEM FROM DAMAGING THE DOOR GASKETS. DO NOT OPERATE THE DISHWASHER UNLESS ALL THE OUTER PANELS HAVE BEEN POSITIONED CORRECTLY. DO NOT TAMPER WITH THE DISHWASHER CONTROLS.
EN WARNINGS BEFORE CLEANING OR SERVICING THE APPLIANCE, REMOVE THE PLUG OR TURN OFF THE MULTI-POLE SWITCH. REMOVE THE WASHING COMPARTMENT DOOR AND DISCONNECT THE MAINS POWER SUPPLY WHEN REMOVING THE OLD DISHWASHER FOR MAINTENANCE OR DISPOSAL. THE SYMBOL ON THE PRODUCT, OR ON THE DOCUMENTS ACCOMPANYING THE PRODUCT, INDICATES THAT THIS APPLIANCE MAY NOT BE TREATED AS HOUSEHOLD WASTE. INSTEAD IT SHALL BE HANDED OVER TO THE APPLICABLE COLLECTION POINT FOR THE RECYCLING OF ELECTRICAL AND ELECTRONIC EQUIPMENT.
EN INSTALLATION INSTRUCTIONS 3 INSTALLATION AND HOOK-UP To install and hook up this appliance, consult the attached installation manual. Bear in mind the following warnings when installing and hooking up the dishwasher. DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF ON THE SHARP EDGES OF THE APPLIANCE; WEAR SAFETY GLOVES. INSTALLATION, REPAIRS AND SERVICING MUST BE PERFORMED BY QUALIFIED AND AUTHORIZED TECHNICIANS.
EN INSTALLATION INSTRUCTIONS CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH THE RATINGS ON THE NAME PLATE OF THE APPLIANCE POSITIONED ON THE INNER EDGE OF THE DOOR. IN THE EVENT OF DAMAGE TO THE SUPPLY CORD, HAVE IT REPLACED BY THE MANUFACTURER OR AN AUTHORIZED TECHNICAL SERVICE CENTRE. THIS APPLIANCE MUST BE EARTHED. IN CASE OF A MALFUNCTION OF FAULT, THE EARTH REDUCES THE RISK OF ELECTROCUTION BY PROVIDING THE ELECTRICAL CURRENT WITH AN ALTERNATIVE, LESS RESISTANT PATH.
EN INSTALLATION INSTRUCTIONS DO NOT USE EXTENSION CORDS, ADAPTORS OR SHUNT CONNECTIONS IN ORDER TO AVOID THE POSSIBILITY OF OVERHEATING OR BURNING, WITH CONSEQUENT FIRE HAZARD. Rev 0.
EN USER INSTRUCTIONS 4 OPERATING INSTRUCTIONS BEFORE STARTING TO USE THE APPLIANCE, MAKE SURE YOU HAVE READ AND UNDERSTOOD ALL THE WARNINGS CONTAINED IN CHAPTER 2 “IMPORTANT SAFETY INSTRUCTION”. Once the dishwasher has been correctly installed, prepare for use as follows: • adjust the water softening system; • add the regenerating salt; • add the rinse-aid and detergent. 14 Rev 0.
EN USER INSTRUCTIONS 4.1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time. The dishwasher is equipped with an automatic softening system which uses a special regenerating salt to reduce the hardness of the water. The dishwasher is factory set for water hardness level 3 (average hardness 41-60°dF – 24-31°dH / 23.6-35 gpg).
EN USER INSTRUCTIONS SA LT A Fig. 4-02 • When using the dishwasher for the first time, in addition to the salt it is also necessary to add one liter of water to the container. • Each time the salt container is refilled, make sure that the cap (ref. A fig. 4-01) is securely closed. The mixture of water and detergent must never penetrate the salt container, as this would compromise the operation of the regeneration system. In the event of this occurring, the warranty will be invalidated.
EN USER INSTRUCTIONS 4.2 Using the rinse-aid and detergent dispensers The detergent and rinse aid dispensers are situated on the inner part of the door: the detergent dispenser (ref. A fig. 4-03) is on the left, and the rinseaid dispenser (ref. B fig. 4-03) is on the right. A B Fig. 4-03 WITH THE EXCEPTION OF THE SOAK PROGRAM, BEFORE EVERY WASHING CYCLE IT IS NECESSARY TO ADD THE REQUIRED AMOUNT OF DETERGENT TO THE DETERGENT DISPENSER.
EN USER INSTRUCTIONS 4.2.1 Adding the rinse-aid The rinse aid helps the dishes dry faster and prevents the formation of scale deposits and staining; it is automatically added to the water during the final rinse cycle, from the container situated on the inner side of the door. B A C Fig. 4-04 To add rinse aid: • Open the door. • Rotate the container cover (ref. A fig. 4-04) anticlockwise by ¼ of a turn and remove it. • Add the rinse aid until the container is full (approximately 140 ml).
EN USER INSTRUCTIONS • To adjust the rinse aid setting, rotate the dispenser cover (ref. A fig. 4-04) through a quarter turn in an anticlockwise direction and remove it. • Then use a screwdriver to rotate the rinse aid selector to the desired position. • Replace the cover (ref. A fig. 4-04) by turning it in a clockwise direction until it is fully closed. • The amount of rinse aid must be increased if the washed dishes appear dull or feature circular stains.
EN USER INSTRUCTIONS A B Fig. 4-06 • When a program with hot prewash is selected (see program table in the “Description of Controls” manual), extra detergent must be placed in the cavity (ref. A or B fig. 4-06, depending on models). • Only use dishwasher-specific detergents. For optimal washing results it is important to use a good quality detergent. • The detergent packs must be sealed and stored in a dry place to prevent the formation of lumps which may negatively affect washing results.
EN USER INSTRUCTIONS • When using detergent tabs, place them in the cutlery basket. The dispenser has been designed for powder or liquid detergent. As the cover does not open completely during the washing cycle, tabs are not fully released (dissolved). This could generate the following problems: - insufficient detergent released during the cycle and poor washing results; - the detergent is compacted in the dispenser and is released during the final rinse cycle.
EN USER INSTRUCTIONS MAKE SURE that the items being washed are dishwasher-safe. Items which are not dishwasher-safe: • Wooden dishes, pots or pans: these may be damaged by the high washing temperatures. • Handcrafted items: these are rarely suitable for washing in a dishwasher. The relatively high water temperatures and the detergents used may damage them. • Lightweight objects: place lightweight objects in the upper rack where the water pressure is lower.
EN USER INSTRUCTIONS 4.4 Using the racks The dishwasher has a capacity of 10 place-settings, including serving dishes. Examples of loading 10 place-settings in the upper rack (see fig. 4-07) and in the lower rack (see fig. 4-08) are shown below; move the upper rack to its bottom position when loading in this way. Fig. 4-07 Fig. 4-08 Rev 0.
EN USER INSTRUCTIONS 4.4.1 Lower rack The lower rack receives the full force of the lower spray arm, and should therefore be used for the “toughest” items with a heavier degree of soiling. All types and combinations of loads are permitted, provided that the dishes, pots and pans are arranged with all the soiled surfaces exposed to the water jets coming from the bottom.
EN USER INSTRUCTIONS Loading the lower rack (see fig. 4-10) Carefully load flat plates, soup plates, dessert and serving dishes, positioning them vertically. Pots, pans and their covers must be loaded upside down. When loading soup plates and dessert bowls, be sure to leave a gap between them. Loading examples: Esempi di caricamento: Fig. 4-10 Rev 0.
EN USER INSTRUCTIONS 4.4.2 Cutlery basket (see fig. 4-11) The cutlery basket can be removed to simplify unloading. Arrange the cutlery in an orderly manner inside the basket, with the handles pointing downwards and taking care not to injure yourself with the knife blades. The basket is suitable for all types of cutlery, except those long enough to interfere with the upper spray arm.
EN USER INSTRUCTIONS 4.4.3 Upper rack (vedi fig. 4-12, 4-13) It is recommended to load the upper rack with small- or medium-sized items such as glasses, small plates, tea or coffee cups, shallow bowls and light objects made from heat resistant plastic. If the upper rack is used in the lowermost position, it can also be loaded with serving dishes, provided they are only slightly soiled. The two tip-up “cutlery baskets” on the right-hand side of the rack can be opened or closed as required (see fig. 4-12).
EN USER INSTRUCTIONS Loading the upper rack (vedi fig. 4-14) Load plates facing forward; cups, bowls etc. must always be facing downwards. The left-hand side of the rack can be loaded with two layers of cups and glasses. The right-hand side can be filled with plates and side-plates, fitted upright into the supports provided. Loading examples: Esempi di caricamento: Fig. 4-14 28 Rev 0.
EN USER INSTRUCTIONS Adjusting the upper rack The upper rack can be adjusted in two positions, according to the user’s needs and according to the height of the dishes in the lower rack. Proceed as follows: • pull out the right-hand rack guide. Release the corresponding stop (ref. A fig.
EN USER INSTRUCTIONS 5 CLEANING AND USER-MAINTENANCE BEFORE CARRYING OUT ANY WORK, ALWAYS DISCONNECT THE APPLIANCE FROM THE ELECTRICAL POWER SUPPLY. 5.1 General warnings and recommendations NEVER USE ABRASIVE AND/OR CORROSIVE DETERGENTS TO CLEAN THE APPLIANCE. Clean the outer surfaces and door-lining of the dishwasher regularly using a soft cloth moistened with a neutral detergent (not abrasive and/or corrosive) suitable for painted surfaces. Clean the door gaskets with a damp sponge.
EN USER INSTRUCTIONS 5.2 Cleaning the water intake filter (only some models) The water intake filter (ref. B fig. 5-01) located at the outlet of the water supply tap needs to be cleaned periodically. After having closed the water supply tap, unscrew the end (ref. A fig. 5-01) of the water intake hose (use a pair of pliers, if necessary), remove the filter (ref. B fig. 5-01) and clean it delicately under running water (at room temperature). Reassemble the filter (ref. B fig.
EN USER INSTRUCTIONS A B Fig. 5-02 Fig. 5-03 B A Fig. 5-04 ••• • 32 Rev 0.
EN USER INSTRUCTIONS 5.4 Cleaning the filter unit • Periodically inspect the filter unit (ref. A fig. 5-05) and, if necessary, clean it under running water (at room temperature), using a stiff brush. To remove the filter, grip the handle, turn anticlockwise and lift upwards; • push the centre filter (ref. A fig.
EN USER INSTRUCTIONS 5.5 General warnings and recommendations for correct maintenance • Clean the filters under running water (at room temperature) using a stiff brush. • When removing the filter, take care that there are no food residues on it. If any residues fall into the washing pit (ref. A fig. 5-07), they might block hydraulic components or foul the spray arm nozzles.
EN USER INSTRUCTIONS Prolonged disuse • Run the soak program twice in succession. • Unplug the power cord from the socket. • Leave the door slightly open in order to prevent the formation of unpleasant odors inside the washing tank. • Fill the rinse-aid dispenser. • Shut off the water supply tap. Before starting the dishwasher after prolonged disuse • Check that there are no deposits of sludge or rust inside the water pipe: if there are, allow the water to run from the water supply tap for a few minutes.
EN USER INSTRUCTIONS If the dishes fail to dry or remain dull, check that: • there is rinse aid inside the special container; • the rinse-aid dispenser setting is correct; • the detergent used is of good quality and has not lost its effectiveness (for example, through incorrect storage, with the box left open). If the dishes show signs of streaking, staining, etc., check that: • the rinse aid dispenser setting is not too high.
EN USER INSTRUCTIONS 6 TECHNICAL DATA (SEE TAB. 6-01) Width 44.7 cm ÷ 44.9 cm (17 - 19/32” ÷ 17 - 43/64”) Depth measured flush with the outer edge of the control panel 55 cm (21 - 21/32”) Height from 82 to 87 cm (from 32 - 9/32” to 34 - 1/4”) Capacity 10 standard place-settings Water supply pressure min. 7 - max. 130 PSI (min. 0.5 – max. 9 bar) Electrical characteristics See rating plate Tab. 6-01 Rev 0.
EN CONTENTS Contents 1 INTRODUCTION ....................................................................................... 3 2 SAFETY INFORMATION ............................................................................ 5 3 INSTALLATION MATERIAL ......................................................................... 8 3.1 Kit supplied with dishwasher (models sta_4645/sta_8743) ......................... 9 3.2 Kit supplied with dishwasher (models pla_8743) .....................................
EN 2 Rev 0.
EN INTRODUCTION 1 INTRODUCTION Thank you for choosing one of our products. To install this dishwasher correctly and safely, please read this manual carefully. The manual is divided into sections giving you a step-by-step guide to installation of the appliance. The texts are easy to understand and are complete with detailed illustrations. This user-friendly manual will provide answers to all your questions about installation of the dishwasher.
EN INTRODUCTION Symbols used in this manual (see tab. 1-01) DANGER. This symbol highlights information and warnings which, if not observed, may compromise personal safety or damage the appliance. DANGER OF ELECTROCUTION. This symbol highlights information and warnings of an electrical nature which, if not observed, may compromise personal safety or damage the appliance. This symbol highlights general information and warnings. Tab. 1-01 4 Rev 0.
EN WARNINGS 2 SAFETY INFORMATION THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE AND MUST THEREFORE BE KEPT INTACT TOGETHER WITH THE MACHINE. BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USE, AND COMPLIES WITH THE DIRECTIVES CURRENTLY IN FORCE, INCLUDING THE PREVENTION AND ELIMINATION OF RADIO FREQUENCY INTERFERENCE.
EN WARNINGS TWO PEOPLE WEARING SAFETY GLOVES ARE REQUIRED TO LIFT THE DISHWASHER. DO NOT LEAVING DISCARDED PACKAGING MATERIALS UNSUPERVISED WITHIN THE HOME. SEPARATE THE VARIOUS PACKAGING MATERIALS AND TAKE THEM TO THE NEAREST SORTED WASTE COLLECTION CENTRE. KEEP CHILDREN, PHYSICALLY AND/OR MENTALLY IMPAIRED ADULTS, AND ANIMALS AWAY FROM PACKAGING WASTE; DANGER OF SUFFOCATION. BEFORE PROCEEDING WITH INSTALLATION, DISCONNECT THE MAINS POWER SUPPLY FROM THE WORK AREA.
EN WARNINGS DO NOT USE EXTENSION CORDS, ADAPTORS OR SHUNT CONNECTIONS IN ORDER TO AVOID THE POSSIBILITY OF OVERHEATING OR BURNING, WITH CONSEQUENT FIRE HAZARD. THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE TO PERSONS, ANIMALS OR PROPERTY RESULTING FROM FAILURE TO OBSERVE THE ABOVE PRECAUTIONS, FROM TAMPERING WITH EVEN A SINGLE COMPONENT OF THE APPLIANCE, OR FROM THE USE OF UNORIGINAL SPARE PARTS. IF IN DOUBT ABOUT THE CONTENTS OF THIS MANUAL, CONTACT THE TECHNICAL ASSISTANCE SERVICE. Rev 0.
EN INSTALLATION INSTRUCTIONS 3 INSTALLATION MATERIAL To install the dishwasher correctly, the following materials are required: • Phillips screwdriver (ref. A fig. 3-01); • spirit level (ref. B fig. 3-01); • tape measure (ref. C fig. 3-01); • compass saw (ref. D fig. 3-01); • pencil (ref. E fig. 3-01); • file (ref. F fig. 3-01); • 13 mm open-ended wrench (ref. G fig. 3-01); • plumbing pliers (ref. H fig. 3-01); • drill (ref. I fig. 3-01); • safety gloves (ref. L fig. 3-01).
EN INSTALLATION INSTRUCTIONS 3.1 Kit supplied with dishwasher (models sta_4645/sta_8743) The kit supplied with the dishwasher comprises: • adhesive steam guard (ref. A fig. 3-02); • 1 steel steam guard (ref. B fig. 3-02);* • 1 template for door panel (ref. C fig. 3-02); • 2 hooks for door panel (ref. D fig. 3-02); • 8 screws for securing the door panel hooks (ref. E fig. 3-02); • 2 screws for securing the door (ref. F fig. 3-02); • 2 screws for fixing the dishwasher to the adjacent walls (ref. G fig.
EN INSTALLATION INSTRUCTIONS 3.2 Kit supplied with dishwasher (models pla_8743) The kit supplied with the dishwasher comprises: • adhesive steam guard (ref. A fig. 3-03); • 1 steel steam guard (ref. B fig. 3-03);* • 1 template for door panel (ref. C fig. 3-03); • 2 hooks for door panel (ref. D fig. 3-03); • 8 screws for securing the door panel hooks (ref. E fig. 3-03); • 2 screws for securing the door (ref. F fig. 3-03); • 2 screws for fixing the dishwasher to the adjacent walls (ref. G fig.
EN INSTALLATION INSTRUCTIONS 4 DIMENSIONS OF DISHWASHER (See fig. 4-01) Model STA8743 STA8614X STA4645 PLA8743X PLA68XU A (height) 86 cm ÷ 91 cm 33-55/64” ÷ 3555/64” 86 cm ÷ 91 cm 33-55/64” ÷ 3555/64” 82 cm ÷ 87 cm 32-9/32” ÷ 34-1/4” 86 cm ÷ 91 cm 33-55/64” ÷ 3555/64” 86 cm ÷ 91 cm 33-55/64” ÷ 3555/64” B (width) C (depth) 59.7 cm ÷ 59,9 cm 23-1/2” ÷ 23-37/64” 55 cm 21-21/32” 59.7 cm ÷ 59.9 cm 23-1/2” ÷ 23-37/64” 60 cm 23-5/8” 44.7 cm ÷ 44.9 cm 17-19/32” ÷ 17-43/64” 55 cm 21-21/32” 59.
EN INSTALLATION INSTRUCTIONS 5 INSTALLATION AND HOOK-UP DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF ON THE SHARP EDGES OF THE APPLIANCE. Remove the polystyrene rack blocks. Position the appliance in the chosen installation position. The sides and rear of the appliance can lie against kitchen units or walls. If the dishwasher is installed next to a heat source, separate it with a heat insulating panel in order to prevent overheating and malfunctions.
EN INSTALLATION INSTRUCTIONS • If the appliance is not in a niche and can therefore be accessed on one side, cover the door hinge area for safety reasons (cutting hazard). Covers are available as accessories from specialized retailers or from the Technical Service Centre. • To build in the dishwasher, purchase the relative kit from specialized retailers or from the Technical Service Centre. 5.1 Leveling 5.1.1 Mounting the feet (only for some models) Turn the appliance upside-down (see fig. 5-01).
EN INSTALLATION INSTRUCTIONS 5.1.2 Levelling the appliance Level the appliance using the relative adjustable feet (e.g.: ref. A fig. 5-02); use an open-ended wrench to rotate the feet until the dishwasher is perfectly level. Some models are fitted with just one rear foot which can be adjusted with a screw located at the bottom front of the appliance (ref. A fig. 5-03); use a suitable Phillips screwdriver to turn the screw until the dishwasher is perfectly level.
EN INSTALLATION INSTRUCTIONS A Fig. 5-03 5.2 Connections Install the dishwasher so as to allow ease of access to the electrical and hydraulic connections through the adjacent unit. These connections must never be behind the dishwasher. The inlet and drain hoses can be pointed in all directions. make sure that they are not bent, crushed or too tight. Tighten the ring nut after pointing the hoses in the required direction.
EN INSTALLATION INSTRUCTIONS A through hole with a diameter of at least 8 cm (5/32”) is required to pass the hoses and power cord (ref. A fig. 5-05). Make sure there area no rough edges that could damage the power cord or hoses. If the dishwasher is installed in a metal unit protect the edge of the through hole for the hoses and power cord with a gasket. Do not use extension cords when making the electrical connection as these do not guarantee safety.
EN INSTALLATION INSTRUCTIONS 5.2.1.1 Connecting to the water tap Connect the inlet hose to a threaded ¾” gas cold water tap, fitting the supplied filter (ref. A fig. 5-06). Firmly secure the hose by tightening the relative ring nut with your hands (ref. B fig. 5-06); finish by tightening another ¼ turn using a pair of plumbing pliers. For models fitted with ACQUASTOP (ref. C fig. 5-06) the filter is already present in the threaded ring nut.
EN INSTALLATION INSTRUCTIONS Do not cut the inlet hose (see fig. 5-07). If the hose is cut, the dishwasher will not work, water will leak and you may be injured. If the hose is too long, wind it up tidily and place it behind the appliance. The cable harness and electrical components must not come into contact with the hydraulic system and the water inlet and drain hoses. Fig. 5-07 When connecting the dishwasher drain hose to the sink make sure that the hose is not bent (ref. A fig.
EN INSTALLATION INSTRUCTIONS 5.2.1.2 Connecting the drain hose Connecting to a drain Insert the relative hose into a drain with a minimum diameter of 4 cm (1-37/64”) (ref. A fig. 5-09); alternatively, place the hose on the sink (ref. B fig. 5-09) using the supplied hose support (see fig. 5-10), but taking care to avoid obstructions or excessive curving. Make sure the hose cannot fall out. For this purpose, the hose support is fitted with a hole (ref. A fig.
EN INSTALLATION INSTRUCTIONS Connecting to a “T” union of the drain circuit MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Connect the dishwasher drain hose (ref. A fig. 5-11) to the “T” union (ref. B fig. 5-11) of the drain circuit using a 38 to 50 mm (1-1/2 to 2”) screw clamp* (ref. C fig. 5-11); if necessary, cut the end of the dishwasher drain hose (ref. D fig.
EN INSTALLATION INSTRUCTIONS Connecting to a waste disposal unit with an air gap MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Remove the cover of the waste disposal unit (ref. A fig. 5-12). 2. Connect the dishwasher drain hose (ref. B fig. 5-12) to the air gap (ref. C fig. 5-12) using the wide spring clamp (ref. D fig. 5-12); if necessary, cut the end of the dishwasher drain hose (ref. E fig.
EN INSTALLATION INSTRUCTIONS Connecting to the air gap (no waste disposal unit) MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Connect the dishwasher drain hose (ref. A fig. 5-13) to the air gap (ref. B fig. 5-13) using the wide spring clamp (ref. C fig. 5-13); if necessary, cut the end of the dishwasher drain hose (ref. D fig. 5-13) (do not cut the corrugated section).
EN INSTALLATION INSTRUCTIONS Connecting to a waste disposal unit (no air gap) MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Remove the cover of the waste disposal unit (ref. A fig. 5-14). 2. Connect the dishwasher drain hose (ref. B fig. 5-14) to the waste disposal unit inlet (ref. C fig. 5-14), using the wide spring clamp (ref. D fig. 5-14). A D C B Fig. 5-14 Rev 0.
EN INSTALLATION INSTRUCTIONS 5.2.2 Electrical connections and warnings CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH THE RATINGS ON THE NAME PLATE OF THE APPLIANCE POSITIONED ON THE INNER EDGE OF THE DOOR. IN THE EVENT OF DAMAGE TO THE SUPPLY CORD, HAVE IT REPLACED BY THE MANUFACTURER OR AN AUTHORIZED TECHNICAL SERVICE CENTRE. THIS APPLIANCE MUST BE GROUNDED.
EN INSTALLATION INSTRUCTIONS PLUG IS NOT SUITABLE FOR THE SOCKET, CALL IN A QUALIFIED ELECTRICIAN TO FIT A SUITABLE PLUG. The plug at the end of the power cord and the corresponding socket must be of the same type and must conform to current regulations governing electrical appliances. The plug must be accessible after installation. Never remove the plug by pulling on the wire. If the power cord is damaged, have it replaced by the manufacturer or an authorized service centre.
EN INSTALLATION INSTRUCTIONS Fig. 5-16 Fig. 5-17 Push the dishwasher into position, taking care not to twist or crush the power cord or hoses (see fig. 5-18). TWO PEOPLE WEARING SAFETY GLOVES ARE NEEDED TO PUSH THE DISHWASHER INTO PLACE. Fig. 5-18 26 Rev 0.
EN INSTALLATION INSTRUCTIONS 5.3.2 Procedure for mounting the door panel (models sta_4645/sta_8743) Mount the door panel. Place the template on the inner surface of the panel, centering it along the upper side and matching up the reference locators (ref. A fig. 5-19); mark the position of the door hooks with a pencil (see fig. 5-19). Remove the template and use a drill with a suitable bit to make holes at the points marked on the panel. A A Fig.
EN INSTALLATION INSTRUCTIONS Drill holes for the panel handle using a drill with a suitable bit. Use the screwdriver to secure the door handle before hooking the panel to the dishwasher (see fig. 5-21). N.B.: the screws are not supplied. Fig. 5-21 Attach the door panel: fit the hooks into their slots on the dishwasher and allow the panel to slide downwards and slip in to place (see fig. 5-22). 1 2 Fig. 5-22 28 Rev 0.
EN INSTALLATION INSTRUCTIONS Secure the door to the panel with the supplied screws. The panel must have a minimum thickness of 20 mm (25/32”) (see fig. 5-23). Fig. 5-23 Make sure the dishwasher door, complete with panel, opens comfortably and that the base plate (ref. A fig. 5-24) does not prevent it from opening fully. If the base plate prevents the door from opening, mark out the section to remove (see fig. 5-24), take out the base plate and cut it along the marking using a compass saw (see fig. 5-25).
EN INSTALLATION INSTRUCTIONS Fig. 5-25 30 Rev 0.
EN INSTALLATION INSTRUCTIONS 5.3.3 Procedure for mounting the door panel (models pla_8743) Mount the door panel. Place the template on the inner surface of the panel, centering it along the upper side and matching up the reference locators (ref. A fig. 5-26); mark the position of the door hooks with a pencil (see fig. 5-26). Remove the template and use a drill with a suitable bit to make holes at the points marked on the panel. A A Fig.
EN INSTALLATION INSTRUCTIONS If a gap is created between the control panel and the door panel (ref. A fig. 5-28), use the supplied strips (ref. B fig. 5-28) to fill it. The number of strips depends on the size of the gap. B A Fig. 5-28 Position the strips between the control panel and the door panel of the dishwasher (ref. A fig 5-29) and fix them from under the control panel with the supplied screws (ref. B fig. 5-29) using a screwdriver. Adjust the strips until a suitable compromise is reached.
EN INSTALLATION INSTRUCTIONS Attach the door panel: fit the hooks into their slots on the dishwasher and allow the panel to slide upwards and slip into place (see fig. 5-30). 2 1 Fig. 5-30 Secure the door to the panel with the supplied screws. The panel must have a minimum thickness of 20 mm (25/32”) (see fig. 5-31). Fig. 5-31 Rev 0.
EN INSTALLATION INSTRUCTIONS Make sure the dishwasher door, complete with panel, opens comfortably and that the base plate (ref. A fig. 5-32) does not prevent it from opening fully. If the base plate prevents the door from opening, mark out the section to remove (see fig. 5-32), take out the base plate and cut it along the marking using a compass saw (see fig. 5-33). 605 m m (24.2 ”) A Fig. 5-32 Fig. 5-33 34 Rev 0.
EN INSTALLATION INSTRUCTIONS 5.3.4 Completion of installation (all models) Finish the cut with a file (see fig. 5-34) in order to remove any burrs and/or imperfections. Put back the base plate (see fig. 5-35) and try to open the dishwasher door fully; if the base plate still obstructs the door, repeat the above operations. Fig. 5-34 Fig. 5-35 Rev 0.
EN INSTALLATION INSTRUCTIONS Before securing the dishwasher to the adjacent units, attach the gaskets to the sides. Remove the adhesive band on the gasket (see fig. 5-36). Fig. 5-36 Fix the gasket to the dishwasher, inserting it in the seat on the sides towards the front (see fig. 5-37), and making sure that the long side of the gasket, the one with the hole for inserting the screw, is attached to the outside of the dishwasher; the hole in the long side must match the hole in the dishwasher (see ref.
EN INSTALLATION INSTRUCTIONS A Fig. 5-38 Fig. 5-39 shows the state of the dishwasher after the above operations are performed. Fig. 5-39 Rev 0.
EN INSTALLATION INSTRUCTIONS Tighten the supplied screws with a screwdriver; this operation definitively fixes the dishwasher to the adjacent units; cover the side holes using the supplied plugs (ref. A fig. 5-40). A Fig. 5-40 5.4 Testing After installation, test the dishwasher by starting a work cycle. Check for leaks and make sure the appliance does not malfunction. 38 Rev 0.
Align with the top edge of the door panel. Aligner au bord supérieur du panneau de la porte. Alinear respecto del borde superior del panel puerta. Alinhe com a borda superior do painel da porta. 444mm (17-15/32) DX Align with the top edge of the door panel. Aligner au bord supérieur du panneau de la porte. Alinear respecto del borde superior del panel puerta. Alinhe com a borda superior do painel da porta.