Assembly Instruction

ManualsBrandsSol 72 Outdoor ManualsLightingJayde 1 -Light 23'' H Hardwired Lantern Head

Part

Description

Quantity

1pc.

3 pcs.

Finial

Package Contents

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing

the fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool

before removal. Do not subject glass parts to any shock while in operation or shattering may result.

Mounting Screw

1of5

Waterproof Washer

Fixture Hood Assembly

ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters, wire

strippers,electrical tape,safety glasses.

EstimatedAssemblyTime:20-30 minutes

Preparation:Identify andinspect allparts beforebeginning installation.Checkpackage

contentlist anddiagrams belowto besureallpartsarepresent.If anyparts aremissing

ordamaged, donot attemptto assemble,install, oroperatethefixture.Contactcustomer

servicefor replacementparts.

1pc.

Center Stem

1pc.

Fixture Body

BulbRecommended: (3) 60WMaximumCandelabraBase

3 pcs.

Candle Cover

Assembly Instruction

Thank you for purchasing our product.

Need assistance with parts or assembly? Call our customer service or visit our website

Summary of content (5 pages)

PAGE 1
Assembly Instruction Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Bulb Recommended: (3) Candelabra Base 60W Maximum Estimated Assembly Time: 20-30 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
FINISH: MEDICI BRONZE 2 23” 1 12” Dia (3) 60W Candelabra base bulbs (not Supplied) NO. NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2" REPLACEMENT PART DESCRIPTION REQ. 1 CANDLE COVER MEDICI BRONZE 3.125”H 3 2 FINIAL MEDICI BRONZE 1"D X 2.
PAGE 3
Assembly Instruction STEP 1 - Drill Pilot Holes on Post A. Carefully fit the Post Fitter over the end of the Post (not supplied), making sure the Post Fitter is fully seated. B. Mark the drill point for the (3) Mounting Screws, using (3) Mounting Holes as reference. After marking hole locations, remove fixture from post and drill 1/16” pilot holes for screws. Post Fitter Post Figure 1 STEP 2 - Make Wire Connections A. Use standard wire connectors to make all wire connections.
PAGE 4
Assembly Instruction STEP 3 - Attach Fixture Body to Post A. Coat the top 1” of the Post with Clear Silicone Caulk (not supplied) and position the Post Fitter onto the Post. Be sure to seat it completely, aligning the holes in the Fitter with the 1/16” Pilot Holes drilled into the Post. B. Secure the Fixture to Post with (3) Mounting Screws. Post Fitter Mounting Screw Post STEP 4 - Attach Center Stem to Fixture Body Mounting Hole Figure 4 Center Stem a.
PAGE 5
Assembly Instruction STEP 6 - Install Bulb Bulb A. This fixture uses standard bulb with a candelabra screw base. Maximum 60 watts. B. Insert bulb and screw snugly into place. Socket Figure 7 STEP 7 - Attach Fixture Hood to Fixture Body a. Place the Fixture Hood Assembly (D) over the top end of the Center Stem (E), attach to the top edge of the Cage. Pass the Waterproof Washer (F) over the Center Stem (E) and secure with the Finial (B). Hand tighten until snug.