Quick Start Guide

10.29.18
Before Installation
1. Determine the location for the speaker.
2. Perform an obstruction survey using a stud nder to be
certain that there are no obstructions.
3. Position the included cutout template where the speaker is
to be located and pencil an outline on the wall. The cut-out
for the R1C and R1CSUR is 12 3/8” x 12 3/8”
(314mm x 314mm).
4. Cut the mounting hole using a keyhole or drywall saw and
run the speaker wires from the mounting hole to the
amplier location.
NOTE: CONSULT LOCAL BUILDING CODES BEFORE RUNNING
SPEAKER WIRES THROUGH WALLS.
Installation
Sonance Reference Series speakers feature an integral RotoLock
®
mounting system for quick mounting directly into existing walls.
1. Strip 1/4” – 1/2” (6mm – 12mm) of insulation from each
speaker lead.
2. Twist the strands or tin the exposed wire with solder to
ensure that there are no stray strands.
3. The R1C and R1CSUR in-ceiling speakers come with a safety
retention mount on the back of the speaker. To ensure safety,
loop a lanyard through the safety retention mount bracket and
secure the other end to the ceiling joist (see Figure 1).
NOTE: STRAY STRANDS THAT TOUCH EACH OTHER CAN CAUSE
A SHORT-CIRCUIT THAT CAN DAMAGE THE AMPLIFIER.
NOTE: CONSULT LOCAL BUILDING CODES BEFORE SECURING THE
LANYARD TO ANY STRUCTURE.
3. The speaker’s terminals are spring-loaded. Push the top of
each terminal down to open the connector and insert the
exposed wires.
4. The speaker’s positive spring terminal is labeled with a red
dot; the negative spring terminal is labeled with a black dot.
5. Make sure all the RotoLock
®
toggle feet are retracted so that
they are tucked within the speaker frame. Insert the speaker
into the hole in the wall (see Figure 2).
Box Contents
(1) Quickstart Guide
(1) Reference in-ceiling speaker (R1C or R1CSUR)
(1) Speaker cut-out template
7. Tighten the screws on the front of the speaker bae.
The RotoLock
®
toggle feet will automatically rotate into
position and begin clamping the speaker (see Figure 4).
When you notice resistance on the screws the speaker has
been clamped successfully.
8. The micro-trim grille is held in place by several small,
powerful magnets on the speaker frame. Place the grille
against the speaker and the magnets will hold it rmly in
place. When properly installed, the grille trim should make
contact with the wall all the way around the speaker.
IMPORTANT: ALWAYS USE LOW-TORQUE SETTINGS; NEVER OVER
TIGHTEN. NOTE: ADJUSTING THE TENSION OF THE ROTOLOCK
®
CLAMPS SO THAT THE SPEAKER FRAME IS FLAT WILL HELP
ENSURE THAT THE GRILLE CONTACTS THE WALL ALL THE WAY
AROUND THE SPEAKER FOR A PROPER FIT.
6. When installing into double drywall or other thicker wall
materials, you may need to remove part of the two-piece
toggle feet. Use a small screwdriver to gently release the
two locking levers (see Figure 3).
Locking Levers
Remove
Cap
Locking Levers
Figure 3: Releasing the Two Locking Levers
Figure 4: Tightening the RotoLock
®
Screws
RotoLock
®
Screws
33-7916
RotoLock
®
Screws
Figure 1: Safety Retention Mount
NOTE: THE ROTOLOCK
®
SYSTEM CAN ACCOMMODATE A WALL
MATERIAL THICKNESS OF 1 1/4” (32MM) WITH THE TOGGLE FOOT
CAP REMOVED THE SYSTEM CAN ACCOMMODATE A WALL MATERIAL
THICKNESS OF 1 7/8” (48MM).
Figure 2: Inserting the Speaker into the Mounting Hole
RotoLock
®
Screws
(retracted)
©2017 Sonance. All rights reserved. Sonance is a registered trademark of Dana Innovations. Due to continuous product improvement, all features and specications are subject to change
without notice. For the latest Sonance product specication information visit our website: www.sonance.com
SONANCE • 991 Calle Amanecer • San Clemente, CA 92673 USA • Phone: [phone] • FAX: [phone] • Technical Support: [phone]
R1C | R1CSUR QUICKSTART GUIDE
REFERENCE IN-CEILING SPEAKERS