4-652-092-11(1) Energy Station Operating Instructions ERA-210P1 English Français Deutsch © 2000 Sony Corporation
For the Customers in the U.S.A. Safety Information Owner’s Record The model number and serial number are located on the bottom of the station. Record the serial number in the space provided below. Refer to the model and serial number whenever you call upon your Sony AIBO Customer Link. Model No. ERA-210P1 Serial No. ___________ For the Sony AIBO Customer Link, you call 1-800-427-2988 in the U.S. or contact via email at aibosupprt@info.sel.sony.
Regulatory Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
For the Customers in Europe Safety Information WARNING • To prevent fire or shock hazard, do not expose the unit to rain or moisture. • To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. (Contact the AIBO Customer Link on page 6.
Regulatory Information This product has been tested and found to conform to the following Safety Standards. EMC Directive 89/336/EEC EMI EN55022/94+A1/95+A2/97, EN55014/93 + A1/97+A2/99, EN50081-1/ 92 EMS : EN55024/98, EN55014-2/97, EN61000-3-2/95, EN61000-3-3/95, EN50082-1/97 Station has been tested all together as a system and found to conform to the following Safety Standards.
Customer Support How can you contact the AIBO Customer Link? In the United States: 1-800-427-2988 Email address: aibosupport@info.sel.sony.com In Europe: English line: +44(0)-20-7365-2938 German line: +49(0)-69-9508-6310 French line: +33(0)-1-5569-5118 Email address: aibo@sonystyle-europe.com In Hong Kong: +852-2345-2966 Email address: aibo_helpdesk@shk.sony.com.hk In Singapore: +65-473-8500 Email address: AIBO.Link@ap.sony.com Reproduction in whole or in part without written permission is prohibited.
“OPEN-R” is the standard interface for the entertainment robot system that Sony is actively promoting. This interface expands the capability of the entertainment robot through a flexible combination of hardware and interchangeable software to suit various applications. AIBO ERS-210 and Energy Station ERA210P1 conform to the OPEN-R version 1.1. • “AIBO” and the AIBO logo, “OPEN-R,” and the OPEN-R logo are registered trademarks of Sony Corporation.
Table of Contents Features of the Energy Station ....................................................... 12 Index to parts and controls ............................................................. 13 Charging AIBO’s internal battery pack .......................................... 15 Charging a spare battery pack ........................................................ 18 Checking AIBO’s settings .............................................................. 20 Making various settings ......................
Features of the Energy Station The Energy Station ERA-210P1 (referred to as the “station” hereafter) is an AIBO ERS-210-dedicated charging station that provides the following functions: • Charges AIBO’s internal battery pack whenever you place AIBO on the station. • Charges a spare battery pack at the same time it charges AIBO’s internal battery pack. • Provides a display panel that allows you to make various AIBO settings without removing AIBO’s extremities.
Index to parts and controls With the cover open Display panel 13
1 MODE button Press to change the item in the display panel. 2 Charging terminals Charges AIBO’s internal battery pack whenever AIBO is placed on the station. Makes contact with terminals on AIBO’s stomach. 3 AC Adapter terminal (on the bottom of the station) Connect the AC adapter (the one supplied with the AIBO or an optionally available one) to this terminal. 4 Cover 5 SET button Press to set an item or cancel a setting. 6 Spare battery insertion slot Insert a spare battery pack here for charging.
Charging AIBO’s internal battery pack You can charge AIBO’s internal battery pack by placing AIBO on top of the station. It is recommended that you recharge the battery pack at room temperature (10° C to 30° C (50° F to 86° F)). Preparing the station Connect the AC adapter (supplied with AIBO or optional) to the station. Insert the cord into the groove on the bottom of the station. The cord can come out from either the front side or the back side of the station. Plug the cord into a wall outlet.
Place AIBO into pause mode or charging posture. Then put AIBO on top of the station. AIBO icon appears in the display and bars in the AIBO icon indicate the charging level of the internal battery pack. AIBO icon Notes • For details on AIBO’s charging posture, refer to the User’s Guide for the respective AIBO-ware. • The AIBO charging posture may not be displayed by certain AIBO-ware.
While charging is taking place n The mouth in AIBO icon opens and closes. Notes • If AIBO icon appears in the display and its mouth does not open or close, charging is not done. • To charge AIBO’s internal battery pack immediately while AIBO is in active mode, press the pause button on its chest and place it on the station. Charging level Nearly empty Half full Almost full Full When AIBO’s battery is fully charged The AIBO icon in the display raises its right leg.
Charging a spare battery pack You can charge a spare battery pack by inserting it into the station. Open the cover of the station. Then insert the battery pack into the spare battery pack insertion slot with the labeled side facing toward you, and then close the cover. While the battery pack is charging The SUB BATT indicator appears in the display.
Charging level Nearly empty Half full Almost full Full When the spare battery pack is fully charged All bars in the SUB BATT indicator light up. Notes • Do not keep the charged battery pack in the station, as this may damage the battery pack and the station. • If all the charging level bars flash simultaneously, it means the battery pack is not charging properly. If this occurs, check that the battery pack is inserted correctly. If the flashing continues, the battery pack may be defective.
Checking AIBO’s settings While AIBO is on top of the station, use the mode button to check its settings.
Making various settings When AIBO is on top of the station, you can set various items, such as the clock and volume level of the musical tone. Setting the time zone By setting the time zone, you specify the difference in hours from the time at the current location and the UTC (Universal Time Coordinated) time. The difference is expressed as a whole number from –12 to +12. For example, the time zone for Hawaii is –10. For details on the time zones of the world, see “Time zone table” on pages 32 and 33.
2 Press the MODE button repeatedly until the time zone indication appears. 3 Press the SET button to select the time zone. The time zone indication starts to flash. 4 Use the +/– buttons to change the time zone. Then press the MODE button. The setting is entered and the time zone indication resumes. Note The time zone function does not support daylight savings.
Setting the date and time 1 Place AIBO on top of the station and open the cover of the station (page 21). 2 Press the MODE button repeatedly until the date and time indication appears. 3 Press the SET button to set the date and time. The year indication starts to flash. 4 Use the +/– buttons to set the year. Then press the MODE button. The month indication starts to flash. 5 Use the +/- buttons to set the month. Then press the MODE button. The day indication starts to flash.
6 Use the +/– buttons to set the day. Then press the MODE button. The hour indication starts to flash. 7 Use the +/– buttons to set the hour. Then press the MODE button. The minute indication starts to flash. 8 Use the +/– buttons to set the minute. Then press the MODE button. The setting is entered and the date and time indication resumes. Setting the date and time display format Do the procedure below to specify the format in which the date and time is displayed.
3 Press the SET button to set the date display format. The date display format starts to flash. The different formats are “YYMMDD” (year, month, day), “MMDDYY” (month, day, year) and “DDMMYY” (day, month, year). Year/month/day 4 Month/day/year Day/month/year Use the +/– buttons to select the display format. Then press the MODE button to set the time display format. The time display format starts to flash. 5 Use the +/– buttons to select a 12-hour clock or a 24-hour clock. Then press the MODE button.
Notes • The date and time formats return to their default settings when the station is disconnected from the wall outlet. Set the formats again when you connect the station to a wall outlet again. • The default setting for the date format is year, month, day. The default setting for the time format is 12-hour clock. Setting the volume level of AIBO’s musical tone 1 Place AIBO on top of the station and open the cover of the station (page 21).
4 Use the +/– buttons to change the volume level. Then press the MODE button. The setting is entered and the volume level indication resumes. The volume level can be set to four levels. If you select “0,” AIBO’s musical tone is muted. Notes • To cancel the setting, press the SET button. The current settings are displayed again. • Settings cannot be made while AIBO is not on the station. If you attempt to make a setting at this time, the AIBO icon will flash for several seconds.
On handling the Energy Station • While AIBO is on top of the station, do not place any object near it that might interfere with its movements. • Do not touch the charging terminal directly with your hand. Doing so may soil the terminal and cause poor contact. • Do not insert anything other than the battery pack specified for use with AIBO into the spare battery pack insertion slot. • Do not press down hard on the station with your hand or elbow. • Do not drop or shake the station as this may damage it.
For the customers in the U.S.A. Limited warranty SONY ELECTRONICS INC. (“SONY”) warrants this Product and its accessories against defects in material or workmanship as follows: 1. PRODUCTS: For a period of one (1) year from the date of purchase, SONY will, at its option, either repair or replace the defective parts and/or the Product (i.e., Energy Station) with new or rebuilt replacements. After this one (1) year period, you must pay all parts and labor charges. 2.
To obtain warranty service, you must first obtain an event number from AIBO Customer Link (page 6). You will need to return the Product and all accessories to SONY in the original carton, using the original packaging materials. All supplied accessories must be returned with the Product. SONY is not responsible for any damage during shipment arising from the failure to properly pack the Product or accessory being returned to SONY.
This warranty is invalid if the factory applied serial number has been altered or removed from the Product. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. SONY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY ON THIS PRODUCT.
For the customers in the U.S.A. Service procedure 1. Contact the AIBO Customer Link. Its E-mail address is aibosupport@info.sel.sony.com and its toll free number is 1-800-427-2988. 2. If the AIBO Customer Link determines that your unit needs repair, follow the procedure described below. a. The AIBO Customer Link will give you the event number, which is valid for ten days. b. Following the procedure described on the label attached to the box, put AIBO or the designated accessories into the original box.
Troubleshooting If you experience any of the following difficulties, use this troubleshooting guide to remedy the problem. Should the problem persist, contact the AIBO Customer Link (page 6). Symptom Cause/Remedy The AIBO icon in the display panel flashes when you press a button on the station. AIBO is not placed on the station correctly. c Place AIBO on the station correctly (page 16). The display panel does not light up even when AIBO is on the station.
Symptom Cause/Remedy Charging does not start even when AIBO is placed on the station. AIBO is in active mode. c Press the pause button on AIBO’s chest. Depending on the AIBO-ware being used, AIBO enters sleep mode automatically when it is on the staion. For details, refer to the user’s guide supplied with the respective AIBO-ware. Charging does not end. AIBO has entered active mode and charging has been suspended. c AIBO’s internal battery pack is charged only while AIBO is in pause or sleep mode.
Specifications Power requirements 16 V DC Power consumption 30 W Output voltage –20 to 60°C (–4 to 140°F) Storage humidity Capacity of charging battery 1 A at 8.4 V DC (for charging a spare battery pack) Supplied accessories Approx.2 hours* (for charging AIBO’s internal battery pack) (page 15) Approx.3 hours (for charging a spare battery pack) LCD with back-lighting Size: Approx. 40 × 50 mm (1 5 /8 in. × 2 in.) Dimensions Approx. 100 × 94.5 × 347.5 mm (4 in. × 3 3/4 in. × 13 3/4 in.
Time zone table Use this table to enter the appropriate time zone.
Pour les clients en Europe Informations de sécurité AVERTISSEMENT • Pour prévenir tout risque d’incendie ou d’électrocution, ne pas exposer ce robot à la pluie ou à l’humidité. • Pour prévenir tout risque de décharge électrique, ne pas ouvrir le boîtier. Confier l’entretien de ce robot exclusivement au personnel qualifié.
Informations sur les réglementations Ce produit a été testé et jugé conforme aux normes de sécurité suivantes.
Service clientèle Comment contacter le service clientèle AIBO ? Aux Etats-Unis: 1-800-427-2988 Adresse e-mail : aibosupport@info.sel.sony.com En Europe : Contact en Grande-Bretagne : +44(0)-20-7365-2938 Contact en Allemagne: +49(0)-69-9508-6310 Contact en France : +33(0)-1-5569-5118 Adresse e-mail : aibo@sonystyle-europe.com Contact à Hongkong : +852-2345-2966 Adresse e-mail : aibo_helpdesk@shk.sony.com.hk Contact à Singapour: +65-473-8500 Adresse e-mail : AIBO.Link@ap.sony.
“OPEN-R” est l’interface standard du robot de compagnie pour lequel Sony mène une campagne de promotion active. Cette interface étend les capacités du robot de compagnie grâce à une combinaison flexible de matériel et de logiciels interchangeables adaptés à différentes applications. L’AIBO ERS-210 et la station de charge ERA-210P1 sont conformes à la version 1.1 OPENR. • “AIBO”, le logo AIBO, “OPEN-R” et le logo OPEN-R sont des marques déposées de Sony Corporation.
Table des matières Caractéristiques de la station ............................................................ 7 Index des composants et des commandes ...................................................................... 8 Mise en charge de la batterie interne d’AIBO ............................... 10 Mise en charge d’une batterie de rechange .................................... 13 Vérification des réglages d’AIBO .................................................. 15 Effectuer différents réglages .........
Caractéristiques de la station La station de charge ERA-210P1 (appelée “station” dans la suite de ce document) est destinée au AIBO ERS-210. Elle possède les fonctions suivantes: • Charge de la batterie interne d’AIBO dès que vous le placez sur la station. • Charge une batterie de rechange en même temps qu’une batterie interne. • Panneau d’affichage vous permettant d’effectuer différents réglages AIBO sans retirer les extrémités d’AIBO.
Index des composants et des commandes Couvercle ouvert 8 Panneau d’affichage
1 Touche MODE Appuyez sur cette touche pour changer l’élément affiché sur le panneau d’affichage. 2 Borne de charge Charge la batterie interne d’AIBO dès que celui-ci est placé sur la station. Entre en contact avec les bornes situées sur l’estomac d’AIBO. 3 Borne adaptateur secteur (située sous la station) Relie l’adaptateur secteur (fourni avec AIBO ou adaptateur optionnel disponible) à cette borne. 4 Couvercle 5 Touche SET Appuyez sur cette touche pour régler un élément ou annuler un réglage.
Mise en charge de la batterie interne d’AIBO Il suffit de placer AIBO sur la station pour charger sa batterie interne. Il est recommandé de recharger la batterie à température ambiante (10° C à 30° C (50° F à 86° F)). Préparation de la station Branchez l’adaptateur secteur (fourni avec AIBO ou en option) à la station. Insérez le cordon dans l’encoche située sous la station. Le cordon sort à l’avant ou à l’arrière de la station. Branchez le cordon sur la prise murale.
Mettez AIBO en mode pause ou en position de charge puis placez-le sur la station. L’icône d’AIBO apparaît avec des barres indiquant le niveau de charge de la batterie interne. Icône AIBO Remarques • Pour des détails sur la position de charge d’AIBO, reportez-vous au “Guide d’utilisateur” pour AIBO-ware respectifs. • La position de charge peut ne pas être indiquée pour certains AIBO-ware.
Au cours du chargement La bouche de l’icône d’AIBO s’ouvre et se ferme. n Remarque • Si l’icône d’AIBO apparaît sur l’afficheur et que sa bouche ne s’ouvre ou ne se ferme pas, le chargement ne s’effectue pas. • Pour charger la batterie interne d’AIBO immédiatement alors qu’AIBO est en mode actif, appuyez sur la touche pause sur sa poitrine et placez-le sur la station.
Mise en charge d’une batterie de rechange Vous pouvez charger une batterie de rechange en l’insérant dans la station. Ouvrez le couvercle de la station. Puis insérez la batterie dans l’emplacement réservée à la batterie de rechange avec la partie torunee vers le panneau d’affichage, puis fermez le couvercle. Pendant la charge de la batterie Le témoin SUB BATT s’affiche.
Niveau de charge Presque vide A moitié pleine Presque pleine Pleine Lorsque la batterie de rechange est complètement chargée Toutes les barres du témoin SUB BATT s’allument. Remarques • Ne laissez pas la batterie chargée dans la station, cela pourrait endommager la batterie et la station. • Si toutes les barres de niveau de chargement clignotent simultanément, cela signifie que le chargement ne se déroule pas correctement. Si cela se produit, vérifiez que la batterie est insérée correctement.
Vérification des réglages d’AIBO Lorsqu’AIBO se trouve sur la station, vérifiez les réglages d’AIBO à l’aide de la touche mode.
Effectuer différents réglages Lorsqu’AIBO est sur la station, vous pouvez définir différents éléments comme l’heure et le volume de la tonalité musicale. Réglage du fuseau horaire En réglant le fuseau horaire, vous spécifiez la différence en heures, entre l’heure locale et l’heure UTC (Universal Time Coordinated). Cette différence est exprimée en nombre entier compris entre–12 et +12. Par exemple, le fuseau horaire de Hawaï est –10.
2 Appuyez à plusieurs reprises sur la touche MODE, jusqu’à ce que l’indication du fuseau horaire s’affiche. 3 Appuyez sur la touche SET pour sélectionner le fuseau horaire. L’indication du fuseau horaire se met à clignoter. 4 Modifiez le fuseau horaire à l’aide des touches +/–. Appuyez ensuite sur la touche MODE. La configuration est enregistrée et l’indication du fuseau horaire reprend. Remarque La fonction fuseau horaire ne permet pas d’économiser de lumière.
2 Appuyez à plusieurs reprises sur la touche MODE, jusqu’à ce que la date et l’heure s’affichent. 3 Appuyez sur la touche SET pour régler la date et l’heure. L’indication de l’année se met à clignoter. 4 Réglez l’année à l’aide des touches +/–. Appuyez ensuite sur la touche MODE. L’indication du mois se met à clignoter. 5 Réglez le mois à l’aide des touches +/–. Appuyez ensuite sur la touche MODE. L’indication du jour se met à clignoter. 6 Réglez le jour à l’aide des touches +/–.
7 Réglez l’heure à l’aide des touches +/–. Appuyez ensuite sur la touche MODE. L’indication des minutes se met à clignoter. 8 Réglez les minutes à l’aide des touches +/–. Appuyez ensuite sur la touche MODE. La configuration est enregistrée et l’indication de la date et l’heure réapparaît. Réglage du format d’affichage de la date et de l’heure Suivez la procédure ci-après afin de spécifier le format d’affichage de la date et de l’heure.
3 Appuyez sur la touche SET pour régler le format d’affichage de la date. Le format d’affichage de la date commence à clignoter. Les différents formats sont les suivants : “YYMMDD” (année, mois, jour), “MMDDYY” (mois, jour, année) et “DDMMYY” (jour, mois, année). Année/mois/jour 4 Mois/jour/année Jour/mois/année Utilisez les touches +/- pour sélectionner le format d’affichage. Puis, appuyez sur la touche MODE pour régler le format d’affichage de l’heure.
Remarques • Les formats de la date et de l’heure reprennent leur format par défaut lorsque la station est débranchée de la prise murale. Réglez à nouveau les formats lorsque vous branchez la station à une prise murale. • Le paramétrage par défaut du format de la date est l’année, le mois, le jour. Le paramétrage par défaut pour le format horaire est basé sur 12 heures. Réglage du niveau sonore des tonalités musicales d’AIBO 1 Placez AIBO sur la station et ouvrez le couvercle de la station (page 16).
4 Modifiez le niveau sonore à l’aide des touches +/–. Appuyez ensuite sur la touche MODE. La configuration est enregistrée et l’indication du niveau de volume réapparaît. Vous disposez de quatre niveaux de réglage pour le niveau sonore. Si vous sélectionnez “0,” les tonalités musicales d’AIBO sont inaudibles. Remarques • Appuyez sur la touche SET pour annuler le réglage. Les réglages actuels sont de nouveau affichés.
Manipulation de la station de charge • Lorsqu’AIBO se trouve sur la station, ne placez aucun objet susceptible d’entraver ses mouvements à proximité de celle-ci. • Ne touchez pas la borne de charge directement avec vos mains. Ceci pourrait souiller la borne et entraîner des faux contacts. • Insérez uniquement une batterie spécifiée pour AIBO dans le logement pour la batterie de rechange. • N’appuyez pas sur la station avec vos mains ou vos coudes. • Ne faites pas tomber la station et ne la secouez pas.
Dépannage Si vous avez des problèmes, utilisez ce guide pour y remédier. Si le problème persiste, contactez le service clientèle AIBO (page 4). 24 Symptom Cause/Remedy L’icône AIBO du panneau d’affichage clignote lorsque vous appuyez sur une touche de la station. AIBO n’est pas correctement installé sur la statio. c Placez AIBO correctement sur la station (page 11). Le panneau d’affichage ne s’allume pas même lorsque AIBO se trouve sur la station.
Symptom Cause/Remedy Le chargement ne commence pas, même si AIBO se trouve sur la station. AIBO est en mode actif. c Appuyez sur la touche pause située sur la poitrine d’AIBO. En fonction de l’AIBO-ware utilisé, AIBO passe automatiquement en mode sommeil lorsqu’il se trouve sur la station. Pour plus de détails, reportez-vous au guide utilisateur fourni avec les différents AIBO-ware. Le chargement ne se termine pas AIBO est en mode actif et le chargement est suspendu.
Tableau des fuseaux horaires Utilisez ce tableau pour régler les fuseaux horaires appropriés.
27
Spécifications Branchement électrique 16 V DC Consommation électrique 30 W Tension de sortie 20 à 80 % Température de stockage Humidité de stockage 1 A à 8,4 V DC (pour le chargement de la batterie de rechange) Capacité de charge de la batterie Environ 2 heures* (pour le chargement de la batterie interne AIBO) (page 10) Environ 3 heures (pour le chargement d’une batterie de rechange) Affichage à cristaux liquides avec éclairage en arrière-plan Taille : 40 × 50 mm (1 5/8 po. × 2 po.
Sicherheitsinformationen ACHTUNG • Um Feuergefahr und die Gefahr eines elektrischen Schlags zu vermeiden, setzen Sie das Gerät weder Regen noch sonstiger Feuchtigkeit aus. • Um einen elektrischen Schlag zu vermeiden, öffnen Sie das Gehäuse nicht. Überlassen Sie Wartungsarbeiten stets nur qualifiziertem Fachpersonal. Wenden Sie sich bitte an die AIBO-Kundendienst-Hotline (Seite 4). • Hinweis an erwachsene Benutzer bzw.
Gesetzliche Vorschriften Dieses Gerät wurde geprüft und erfüllt folgende Sicherheitsstandards: EMV-Richtlinie 89/336/EWG EMI EN55022/94+A1/95+A2/97, EN55014/93 + A1/97+A2/99, EN50081-1/92 EMS: EN55024/98, EN55014-2/97, EN61000-3-2/95, EN61000-3-3/95, EN50082-1/97 Die Station wurde als Gesamtsystem geprüft und erfüllt folgende Sicherheitsstandards: EN60335-1/94 + A11/95 + A12/98 + A14/98 EN60335-2-29/96 Hinweise zur Konformität mit dem CE-Zeichen (EMV) a) Dieses Gerät entspricht der europäischen Norm EN55022
Kundendienst Wie können Sie die AIBO-Kundendienst-Hotline erreichen? Für Großbritannien: +44(0)-20-7365-2938 Für Deutschland: +49(0)-69-9508-6310 Für Frankreich: +33(0)-1-5569-5118 E-Mail-Adresse: aibo@sonystyle-europe.com Die Reproduktion ganz oder auszugsweise ist ohne schriftliche Genehmigung untersagt. Alle Rechte vorbehalten.
„OPEN-R“ ist die Standardschnittstelle für ein Spielrobotersystem, das Sony aktiv fördern möchte. Ziel dieser Schnittstelle ist es, die Funktionen und Merkmale von Spielrobotern mit Hilfe einer flexiblen Kombination von Hardware und austauschbarer Software für unterschiedliche Anwendungsmöglichkeiten zu erweitern. AIBO ERS-210 und die Energiestation ERF-ERA-210P1 entsprechen der OPEN-RVersion 1.1. • „AIBO“, das AIBO-Logo, „OPEN-R“ und das OPEN-R-Logo sind eingetragene Marken der Sony Corporation.
Inhalt Funktionen und Merkmale der Energiestation ................................. 7 Lage und Funktion der Teile und Bedienelemente ........................... 8 Laden des Akkus in AIBO ............................................................. 10 Laden eines Ersatzakkus ................................................................ 13 Überprüfen von AIBOs Einstellungen ........................................... 15 Vornehmen verschiedener Einstellungen .......................................
Funktionen und Merkmale der Energiestation Die Energiestation ERA-210P1 (im Folgenden einfach “Station” genannt) ist eine dedizierte Ladestation für AIBO ERS-210. Mit der Energiestation können Sie: • Den Akku in AIBO laden, während AIBO auf der Station sitzt. • Einen Ersatzakku laden, während gleichzeitig der Akku in AIBO geladen wird. • Über das Display eine Reihe von Einstellungen an AIBO vornehmen, ohne dass Sie dazu AIBOs Körperteile abnehmen müssen.
Lage und Funktion der Teile und Bedienelemente Mit geöffneter Abdeckung 8 Display
1 Taste MODE Mit dieser Taste können Sie zwischen den Anzeigen im Display umschalten. 2 Ladekontakte Über diese Kontakte wird der Akku in AIBO geladen, während AIBO auf der Station sitzt. Diese Kontakte berühren die Ladekontakte an AIBOs Bauch. 3 Netzteilanschluss (an der Unterseite der Station) Verbinden Sie ein Netzteil (das mit AIBO gelieferte oder ein zusätzlich erhältliches) mit diesem Anschluss. 7 Tasten +/– Mit + erhöhen Sie den Wert einer Einstellung, mit – verringern Sie ihn.
Laden des Akkus in AIBO Um den Akku in AIBOs Innerem aufzuladen, setzen Sie AIBO einfach auf die Station. Es empfiehlt sich, den Akku bei Zimmertemperatur (10 °C bis 30 °C) aufzuladen. Vorbereiten der Station Verbinden Sie das Netzteil (mit AIBO geliefert oder zusätzlich erhältlich) mit der Station. Setzen Sie das Kabel in die Kerbe an der Unterseite der Station ein. Sie können das Kabel zur Vorderseite oder zur Rückseite der Station führen. Stecken Sie das Netzkabel in eine Netzsteckdose.
Schalten Sie AIBO in den Pausemodus oder bringen Sie ihn in die Ladeposition. Setzen Sie AIBO dann auf die Station. Das AIBO-Symbol erscheint im Display und Balken im AIBO-Symbol zeigen den Ladezustand des Akkus in AIBO an. AIBO-Symbol Hinweise • Erläuterungen zu AIBOs Ladeposition finden Sie im “Benutzerhandbuch” zur jeweiligen AIBO-ware. • Die Ladeposition für AIBO steht nicht in jeder AIBO-ware zur Verfügung.
Während des Ladens Das AIBO-Symbol macht das Maul auf und zu. n Hinweise • Wenn das AIBO-Symbol im Display erscheint, AIBO das Maul aber nicht auf und zu macht, wird der Akku nicht geladen. • Wenn der Akku in AIBO aufgeladen werden soll und AIBO sich im aktiven Modus befindet, drücken Sie die Pausetaste auf seiner Brust und setzen Sie ihn auf die Station.
Laden eines Ersatzakkus Sie können einen Ersatzakku laden, indem Sie diesen in die Station einsetzen. Öffnen Sie die Abdeckung der Station. Setzen Sie dann den Akku in den Einschub für den Ersatzakku ein, und zwar so, dass die Seite mit der Beschriftung auf Sie weist, und schließen Sie die Abdeckung. Während der Akku geladen wird Die Anzeige SUB BATT erscheint im Display.
Ladezustand Fast leer Zur Hälfte geladen Fast voll Voll Wenn der Ersatzakku vollständig aufgeladen ist Alle Balken in der Anzeige SUB BATT leuchten. Hinweise • Lassen Sie den geladenen Akku nicht in der Station. Andernfalls können der Akku und die Station beschädigt werden. • Wenn alle Balken zur Anzeige des Ladezustands gleichzeitig blinken, so wird der Akku nicht ordnungsgemäß geladen. Überprüfen Sie in diesem Fall, ob der Akku korrekt eingesetzt ist.
Überprüfen von AIBOs Einstellungen Wenn AIBO auf der Station sitzt, können Sie mit der Taste MODE seine Einstellungen anzeigen lassen.
Vornehmen verschiedener Einstellungen Wenn AIBO auf der Station sitzt, können Sie verschiedene Einstellungen vornehmen, zum Beispiel die Uhrzeit oder den Lautstärkepegel von AIBOs Lautäußerungen. Einstellen der Zeitzone Durch die Einstellung der Zeitzone geben Sie den Zeitunterschied (in Stunden) zwischen Ihrem aktuellen Aufenthaltsort und der Weltzeit (Greenwich-Zeit, Universal Time Coordinated = UTC) an. Dieser Unterschied wird als ganze Zahl zwischen –12 und +12 ausgedrückt.
2 Drücken Sie MODE so oft, bis die Zeitzone angezeigt wird. 3 Wählen Sie mit der Taste SET die Zeitzone aus. Die Zeitzonenangabe beginnt zu blinken. 4 Stellen Sie mit den Tasten +/– die Zeitzone ein. Drücken Sie dann die Taste MODE. Damit haben Sie die Einstellung vorgenommen und die Zeitzone wird wieder angezeigt. Hinweis Bei der Zeitzonenfunktion wird die Sommerzeit nicht berücksichtigt.
2 Drücken Sie MODE so oft, bis Datum und Uhrzeit angezeigt werden. 3 Stellen Sie mit der Taste SET Datum und Uhrzeit ein. Die Jahresangabe beginnt zu blinken. 4 Stellen Sie mit den Tasten +/– das Jahr ein. Drücken Sie dann die Taste MODE. Die Monatsangabe beginnt zu blinken. 5 Stellen Sie mit den Tasten +/– den Monat ein. Drücken Sie dann die Taste MODE. Die Tagesangabe beginnt zu blinken. 6 Stellen Sie mit den Tasten +/– den Tag ein. Drücken Sie dann die Taste MODE.
7 Stellen Sie mit den Tasten +/– die Stunden ein. Drücken Sie dann die Taste MODE. Die Minutenangabe beginnt zu blinken. 8 Stellen Sie mit den Tasten +/– die Minuten ein. Drücken Sie dann die Taste MODE. Damit haben Sie die Einstellung vorgenommen und Datum und Uhrzeit werden wieder angezeigt. Einstellen des Anzeigeformats von Datum und Uhrzeit Mit den unten angegebenen Schritten können Sie einstellen, in welchem Format Datum und Uhrzeit angezeigt werden sollen.
3 Stellen Sie mit der Taste SET das Anzeigeformat für das Datum ein. Das Anzeigeformat für das Datum beginnt zu blinken. Als Anzeigeformat stehen “YYMMDD” (Jahr, Monat, Tag), “MMDDYY” (Monat, Tag, Jahr) und “DDMMYY” (Tag, Monat, Jahr) zur Wahl. Jahr/Monat/Tag 4 Monat/Tag/Jahr Tag/Monat/Jahr Wählen Sie mit den Tasten +/- ein Anzeigeformat aus. Stellen Sie dann mit der Taste MODE das Anzeigeformat für die Uhrzeit ein. Das Anzeigeformat für die Uhrzeit beginnt zu blinken.
Hinweise • Datum- und Uhrzeitformate werden auf die Standardeinstellungen zurückgesetzt, wenn Sie die Station von der Netzsteckdose trennen. Sie müssen diese Formate also erneut einstellen, wenn Sie die Station wieder mit einer Netzsteckdose verbinden. • Die Standardeinstellung für das Datumsformat lautet “Jahr, Monat, Tag”. Die Standardeinstellung für das Uhrzeitformat ist das 12-Stunden-Format.
4 Ändern Sie mit den Tasten +/– den Lautstärkepegel. Drücken Sie dann die Taste MODE. Damit haben Sie die Einstellung vorgenommen und der Lautstärkepegel wird wieder angezeigt. Hinweise • Um eine Einstellung zu verwerfen, drücken Sie die Taste SET. Die aktuellen Einstellungen werden daraufhin wieder angezeigt. • Sie können die Einstellungen nur vornehmen, wenn AIBO auf der Station sitzt.
Umgang mit der Energiestation • Wenn AIBO auf der Station sitzt, achten Sie darauf, dass keine Gegenstände in seiner Nähe ihn in seinen Bewegungen behindern. • Berühren Sie den Ladekontakt nicht mit der Hand. Andernfalls könnte der Kontakt verschmutzt werden, was zu einer Beeinträchtigung der Verbindung führt. • Setzen Sie ausschließlich einen Akku, der für AIBO gedacht ist, in den Einschub für den Ersatzakku ein. • Drücken Sie mit der Hand oder dem Ellenbogen nicht zu fest auf die Station.
Störungsbehebung Sollte eine der folgenden Störungen auftreten, versuchen Sie, diese anhand der folgenden Checkliste zu beheben. Sollte sich das Problem auf diese Weise nicht lösen lassen, wenden Sie sich bitte an die AIBOKundendienst-Hotline (Seite 4). 24 Symptom Ursache/Abhilfe Das AIBO-Symbol im Display blinkt, wenn Sie eine Taste auf der Station drücken. AIBO sitzt nicht richtig auf der Station. c Setzen Sie AIBO richtig auf die Station (Seite 11).
Symptom Ursache/Abhilfe Der Ladevorgang beginnt nicht, auch wenn Sie AIBO auf die Station setzen. AIBO befindet sich im aktiven Modus. c Drücken Sie die Pausetaste auf AIBOs Brust. Je nach der verwendeten AIBO-ware wechselt AIBO automatisch in den Schlafmodus, wenn er auf der Station sitzt. Näheres dazu finden Sie im Benutzerhandbuch zu der betreffenden AIBO-ware. Das Laden geht nicht zu Ende. AIBO hat in den aktiven Modus gewechselt. Der Ladevorgang wurde unterbrochen.
Tabelle der Zeitzonen Geben Sie anhand dieser Tabelle die richtige Zeitzone ein.
27
Technische Daten Betriebsspannung 16 V Gleichstrom Leistungsaufnahme 30 W Ausgangsspannung Luftfeuchtigkeit bei Betrieb 20 bis 80 % Lagertemperatur -20 bis 60 °C Luftfeuchtigkeit bei Lagerung 1,5 A bei 16 V Gleichstrom (beim Laden des Akkus in AIBO) 10 bis 90 % Akkuladekapazität 1 A bei 8,4 V Gleichstrom (beim Laden eines Ersatzakkus) Mitgeliefertes Zubehör 2300 Ah Bedienungsanleitung Ladedauer ca. 2 Stunden* (beim Laden des Akkus in AIBO) (Seite 10) ca.
Printed in Japan * 4 6 5 2 0 9 2 1 1 * (1)