DIGITAL VIDEOCASSETTE RECORDER DVW-A500/1 DVW-500/1 DVW-A500P/1 DVW-500P/1 BKDW-515 CONTROL PANEL INSTALLATION AND MAINTENANCE MANUAL 1st Edition (Revised 3)
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden.
Voor de klanten in Nederland CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Dit apparaat bevat een (CF)n-Li batterij voor memory back-up. Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat bij einde levensduur afdankt. Gooi de batterij niet weg. maar lever hem in als KCA.
Table of Contents Manual Structure Purpose of this manual .............................................................................................. 3 Contents ..................................................................................................................... 3 Relative manuals ....................................................................................................... 4 1. Installation 1-1. 1-2. 1-3. 1-4. 1-5. 1-6. 1-7. 1-8. Installation of Control Panel .................
4. Maintenance Menu 4-1. 4-2. 4-3. 4-4. ROM Version .............................................................................................. 4-1 VTR Maintenance Menu ............................................................................. 4-1 Panel Maintenance Menu ............................................................................ 4-2 4-3-1. Card Interface Test ..................................................................... 4-2 4-3-2. Buzzer Test ................................
Manual Structure Purpose of this manual This Manual describes the installation instructions for the digital videocassette recorder DVW-A500/1, 500/1, A500P/1, 500P/1 and the Control panel BKDW-515. This manual contains the information necessary when supplying and installing the unit, assuming use by system/service engineers. Contents The sections covered in the manual are summarized below to give you a general under standing of the manual.
Relative manuals Besides this “Installation and Maintenance Manual”, the following manuals are available. • Operation Manual (Supplied with the VTR or the BKDW-515) This manual is necessary for application and operation of the VTR. • Installation Manual (Supplied with the VTR) This manual describes the items are required to install the VTR and its peripherals. If the BKDW-514 control panel is used, refer to this manual.
Section 1 Installation n The BKDW-515 cannot be installed in the BKDW-511 Control Panel Case. for DVW-A500/1, DVW500/1, DVW-A500P/1, DVW-500P/1 1-1. Installation of Control Panel 1. Fix a dummy panel for shipping use at 90 degrees. 2. Loosen the two black screws on the dummy panel. (Loosen the screws until screw’s top are exposed from the surface of the dummy panel.) 3. While pushing the loosened black screws in the direction of the arrow, remove the dummy panel assembly from the arms. 4.
1-2. SYS1, SYS2 ROM Versions 1-3. Removal of Control Panel / Replacement of Arms for DVW-A500, DVW500, DVW-A500P, DVW-500P 4. While pushing the loosened black screws in the direction of the arrow, remove the lower control panel assembly from the arms. 1-2. SYS1, SYS2 ROM Versions The control panel BKDW-515 is applicable to the ROMs on the SS-52 board with the following version. SYS1: 4.0 and higher SYS2: 4.
1-4. Installation of Sub Panel Cover and Switch Cover 1-5. Installation of Control Panel 1-4. Installation of Sub Panel Cover and Switch Cover 1. Install the sub panel cover supplied with BKDW-515 to sub control panel. 1-5. Installation of Control Panel 1. Fix the both arms at 45 degrees. 2. Connect the harness of the control panel to the connector (CN580) on the system set-up panel. 3. Set the notches of the control panel to the claws of the arms, and push the control panel until making a click sound.
1-6. Installation Space 1-6. Installation Space Notes on Installation on Cart Machine . When the digital Betacam recorder is to be mounted on the LMS, you can install not the control panel BKDW515 but the BKDW-514 to the recorder. . When the digital Betacam recorder is to be mounted on the FLEXICART, you can install both of BKDW-514/ 515 to the recorder. As for how to mount the unit in a rack, refer to the Installation Manual supplied with the DVW series.
1-7. Full Reset of Control Panel 1-8. Extension of Control Panel 1-7. Full Reset of Control Panel 1-8. Extension of Control Panel After installing the control panel in DVW-A500 and DVW-500 (DVW-A500P and DVW-500P for PAL), perform the full-reset operation of the control panel only once before it is used. To extend the BKDW-515, prepare the following BKDW510 (Control Panel Extension Kit), AC adapter and the connector box. m .
1-8. Extension of Control Panel Notes when connecting the two BKDW-515 . Setup Setting Data The Current Setup setting data inside of the BKDW-515 is transferred to the VTR just after the communication between the BKDW-515 and VTR are established. The ALARM LED on the front panel blinks during the data communication is incomplete. When the two BKDW-515 are connected to a single VTR, last setting data out of two is written over the former data as the effective setting data.
Section 2 Service Information 2-1.
2-2. Replacing the Battery for Memory Backup 2-2. Replacing the Battery for Memory Backup BT1 inserted into a socket in IC113 (memory for storing setup data and cue data) on the CP-266 board is a battery for memory backup. 4. Insert the tip of a flatbladed screwdriver between IC113 and BT1 to remove BT1. Mark m . Replace a battery for memory backup every seven years. . Store all the setup data (cue data if necessary) in a memory card before replacing the Battery for memory backup.
2-3. EL Panel Replacement 2-3. EL Panel Replacement 5. Disconnect connector CN7 on the CP-266 board and remove the four screws, then remove the EL panel. 1. Turn off the power switch. 2. Disconnect CN580 on the system setup panel and remove the control panel. 3. Remove the four screws, then remove the cover. 4. Remove the seven screws and disconnect connector CN1 on the SW-749 board with the frame lifted from the key panel sub-ass’y.
2-4. Error Message 2-4. Error Message 2-4-1. Operation when Checksum Error of Current Setup Data Occurs If the power switch is turned on when the current setup data on the control panel was destroyed for some trouble, message “CURRENT setup DATA ERROR” is displayed on the EL panel. The current setup data is automatically reset to the factory-setting value at the same time. 2-4-2.
Section 3 Setup Menu This section describes the menu ITEM-F series used during adjustment. For the operation and ITEM-H00 to ITEM-900 series, refer to the Operation Manual. 3-1. ITEM-F Series Display the ITEM-F series according to the procedure below. 1. Press the SETUP key to enter the setup menu. 2. Press the F6 (VTR SETUP) key to enter the VTR SETUP menu. 3. Press the cursor key while pressing the PLAY button.
3-1. ITEM-F Series ITEM DATA Description No. ITEM No. DATA F13 TRACKING CONTROL VIA SEARCH DIAL 0 1 off on Select whether the tracking control operation with search dial is enabled or not during DT head playback. This item is prepared exclusively for DT adjustment and tracking adjustments. After adjustment is completed, return to the factory setting ‘0 (off)’. 0: Tracking control function is disabled during DT head playback.
3-1. ITEM-F Series ITEM DATA Description No. ITEM No. DATA F20 CONFI LED STATUS 0 1 switch status The condition to light CONFI LED on the control panel is selected. 0: CONFI LED lights on when CONFI switch is set to ON. 1: CONFI LED lights on when playing back with CONFI head. Note that CONFI LED indicates the switch status only during the CONFI switch is pressed.
Section 4 Maintenance Menu The self-diagnosis and adjustment of the VTR and control panel can be performed in this maintenance menu. To enter the maintenance mode Press the MAINTENANCE button while pressing the SFT key. To terminate the maintenance mode Press the HOME key. The following descriptions are key operations in the state when the unit is put into the maintenance mode. 4-1. ROM Version The versions of all ROMs are displayed. Available options are displayed.
4-3. Panel Maintenance Menu 4-3. Panel Maintenance Menu 4-3-1. Card Interface Test The self-diagnosis of the control panel can be performed in this panel maintenance menu. A storage/access test for the memory card is executed. n Do not use the memory card in which necessary data is stored. The data is erased. A card can be extracted or inserted even if the power is turned on. To enter the panel maintenance menu Press the F7 (PANEL MAINT) key.
4-3. Panel Maintenance Menu 4-3-3. EL Panel Test 4-3-5. Dial Test An EL panel test is executed. The screen displayed on the EL panel appears while the F6 key is pressed. The displays changes every time the F6 key is pressed. ALL ON : All light. ALL OFF : All go off. V BAR : Displays the test pattern in a vertical line. H BAR : Displays the test pattern in a horizontal line. Interface test between search dial and dial interface is executed. 4-3-4.
4-4. Error Logger 4-4. Error Logger After the power switch is turned on, the error logger function always monitors the unit to detect the errors. When any one of the conditions mentioned as follows, the corresponding message and time code are stored. This menu can be read and checked the contents of these data items in list form. . CH COND RED (Channel Condition Red) When the red CANNEL CONDITION lamp on the upper control panel lights .
BKDW-515 SWC-19 CN580 For FACTORY USE CN6 CN5 POWER ON RESET IC3 DC-DC CONVERTER IC2 IC102 +5V +12V +8V LED,DIAL KEY ADDRESS DC-DC CONVERTER IC1 +8V IN RS-422 RS-232C DRAM 4Mbit IC208 SH7032 CPU CN7 +12V +5V EL I/F LJ32H028 EL DISPLAY 320 x 240dot IC115 32MHz S101 16MHz RESET SW VIDEO RAM CONTROLLER IC207 POWER ON RESET IC105 IC103 32MHz SW-749 KEY SW x 44 ( 6 x 8 SCAN ) LED x 1 CN1 CN3 CPU BUS CN2 MEMORY CARD 64KBytes CN3 CN4 MEMORY CARD I/F PIO IC113 SOLENO
Section 6 Spare Parts 6-1. Notes on Repair Parts 1. Safety Related Components Warning Components marked ! are critical to safe operation. Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts commonality and improvement. Parts list has the present standardized repair parts. 3.
DVW-A500/1, 500/1, A500P/1, 500P/1 6-2. Spare Parts List for VTR B3 x 6 B3 x 6 3 BVTT3 x 6 BVTT3 x 6 5 BVTT3 x 6 BVTT3 x 6 B3 x 6 4 B3 x 6 2 1 Ref. No. or Q’ty Part No.
DVW-A500/1, 500/1, A500P/1, 500P/1 6-3. Packing Materials and Supplied Accessories List for VTR For DVW-A500/1, 500/1 (UC) Ref. No. or Q’ty Part No.
CONTROL PANEL 6-4. Spare Parts List for Control Panel 12 12 BVTT 3x6 BVTT3 x 6 *1 BVTT 3x6 PSW3 x 10 PSW3 x 10 BVTT 3x6 5 W 2.5 SMALL 10 BVTT 3x6 P2 x 8 9 11 W 2.5 SMALL P2 x 8 24 *3 *1 23 1 *2 14 7 *5 N 2.6 17 13 *4 N 2.6 PTPWH 2.6 x 5 *6 19 22 22 17 17 PTPWH 2.6 x 5 6 PSW3 x 6 18 18 PTPWH 2.6 x 5 2 PSW3 x 6 *6 20 No. Part No. N 2.6 SP Description N 2.6 PS2.
CONTROL PANEL 110 PWH2.6 x 5 109 BVTP3 x 8 BVTP3 x 8 PWH2.6 x 5 101 113 103 115 123 121 E-4.0 123 111 104 117 107 116 108 106 114 105 BVTP3 x 8 122 119 120 118 102 112 BVTP3 x 8 B3 x 14 BKDW-515 No. Part No.
BKDW-515 6-5. Packing Materials and Supplied Accessories List for BKDW-515 Ref. No. or Q’ty Part No.
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.
DVW-A500/1 (UC) DVW-500/1 (UC) DVW-A500P/1 (CE) DVW-500P/1 (CE) BKDW-515 (WW) E 3-188-821-04 (2) Sony Corporation B&P Company Printed in Japan 2003.